Anthony Giles
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Anthony Giles has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Richard Marsh
School of Engineering, Cardiff University, Cardiff CF24 3AA, UK
13 shared publications - Daniel Pugh
School of Engineering, Cardiff University , Cardiff CF24 3AA, UK
8 shared publications - Jon Runyon
Cardiff University, Cardiff, UK
8 shared publications - Steven Morris
School of Engineering, Cardiff University, Cardiff CF24 3AA, UK
6 shared publications - Agustin Valera-Medina
College of Physical Sciences and Engineering, Cardiff University, Cardiff CF24 3AA, UK
5 shared publications - Philip Bowen
School of Engineering, College of Physical Sciences and Engineering, Cardiff University, Cardiff CF24 3AA, UK
5 shared publications
Latest Publications
- Open Access
- 25 October 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 148 (3)
Operability Study With Spatial Resolved Temperature and Water Molar Concentration Measurements of a New Pressurized Optical Modular Staged Combustor
A new optical modular staged combustor has been developed to facilitate the study of the staged combustion of alternative fuels, both liquid and gaseous, at elevated inlet pressures and temperatures. Initial testing to characterize the combustor was carried out at pressures of up to 6 bara, for both premixed and nonpremixed methane/air swirling flames with a combustor inlet temperature of 450 K. Exhaust gas analysis together with OH* and CH* chemiluminescence was used to evaluate the operability of the combustor and the quenching effect of the secondary air flow for a range of primary and global equivalence ratios. Laser-induced grating spectroscopy (LIGS) was used to obtain instantaneous local temperatures of the mixture across the secondary air mixing zone. A previously developed analytic approach was used to extract temperature from the measured signal frequencies within the primary flame brush and secondary mixing region, where both burnt and unburnt gases were present. The development of such modular apparatus specifically to allow for the application of novel optical techniques, such as LIGS, enables the future evaluation of different combustor architectures for unconventional fuels. Additionally, this work further demonstrates the development of the LIGS technique for obtaining measurements within complex high-pressure, turbulent swirling flames.
- 25 October 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 148 (3)
Open AccessOperability Study With Spatial Resolved Temperature and Water Molar Concentration Measurements of a New Pressurized Optical Modular Staged Combustor
A new optical modular staged combustor has been developed to facilitate the study of the staged combustion of alternative fuels, both liquid and gaseous, at elevated inlet pressures and temperatures. Initial testing to characterize the combustor was carried out at pressures of up to 6 bara, for both premixed and nonpremixed methane/air swirling flames with a combustor inlet temperature of 450 K. Exhaust gas analysis together with OH* and CH* chemiluminescence was used to evaluate the operability of the combustor and the quenching effect of the secondary air flow for a range of primary and global equivalence ratios. Laser-induced grating spectroscopy (LIGS) was used to obtain instantaneous local temperatures of the mixture across the secondary air mixing zone. A previously developed analytic approach was used to extract temperature from the measured signal frequencies within the primary flame brush and secondary mixing region, where both burnt and unburnt gases were present. The development of such modular apparatus specifically to allow for the application of novel optical techniques, such as LIGS, enables the future evaluation of different combustor architectures for unconventional fuels. Additionally, this work further demonstrates the development of the LIGS technique for obtaining measurements within complex high-pressure, turbulent swirling flames.
- 8 October 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 148 (1)
Surface Roughness Effects on the Operability and Performance of a Hydrogen Jet Burner
Over the past decade, additive manufacturing (AM) has gained considerable traction in the gas turbine industry. Manufacturers now look to AM for the production of critical components central to the combustor architecture. However, AM struggles to achieve satisfactory surface finishes, with its increased surface roughness shown to impact axial velocities, heat release, NOx emissions, and stability limits. Correlations between increased roughness and boundary layer flashback (BLF) resistance are of significant interest for lean premixed combustion of high hydrogen content (HHC) fuels. With the development of innovative burner configurations designed to address static stability issues in HHC fuels, and the growing use of AM in their fabrication, studying roughness effects on these designs is essential. This study aims to quantify the impact of surface roughness on an industry-relevant jet burner configuration, building on previous research by the authors using premixed swirl geometries. A premixed jet burner was developed with an interchangeable section to accommodate varying surface textures. The burner was characterized under atmospheric hydrogen-fired conditions at thermal powers ranging from 10 to 25 kW. Both smooth and rough inserts representing traditional machining and selective laser melting manufacturing techniques were utilized. The findings highlight how surface roughness influences flame topology, static stability, and emissions, providing an experimental basis for future numerical studies on roughness sensitivity in advanced burner designs.
- 8 October 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 148 (1)
Surface Roughness Effects on the Operability and Performance of a Hydrogen Jet Burner
Over the past decade, additive manufacturing (AM) has gained considerable traction in the gas turbine industry. Manufacturers now look to AM for the production of critical components central to the combustor architecture. However, AM struggles to achieve satisfactory surface finishes, with its increased surface roughness shown to impact axial velocities, heat release, NOx emissions, and stability limits. Correlations between increased roughness and boundary layer flashback (BLF) resistance are of significant interest for lean premixed combustion of high hydrogen content (HHC) fuels. With the development of innovative burner configurations designed to address static stability issues in HHC fuels, and the growing use of AM in their fabrication, studying roughness effects on these designs is essential. This study aims to quantify the impact of surface roughness on an industry-relevant jet burner configuration, building on previous research by the authors using premixed swirl geometries. A premixed jet burner was developed with an interchangeable section to accommodate varying surface textures. The burner was characterized under atmospheric hydrogen-fired conditions at thermal powers ranging from 10 to 25 kW. Both smooth and rough inserts representing traditional machining and selective laser melting manufacturing techniques were utilized. The findings highlight how surface roughness influences flame topology, static stability, and emissions, providing an experimental basis for future numerical studies on roughness sensitivity in advanced burner designs.
- 12 January 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (5) , 1-12
Spatial Temperature and Water Molar Concentration Measurements Using Thermal and Electrostrictive Laser-Induced Grating Spectroscopy During Operation of a Swirl Burner at Pressure
Laser-Induced Grating Spectroscopy (LIGS) was applied in a high-pressure combustion facility. Instantaneous (sub-μs), spatially resolved (within 5 mm) measurements of temperature and molar fractions of water were obtained using thermal and electrostrictive LIGS signals. Temperatures up to 1800 K and water molar fractions between 0.01 and 0.12 were measured. A new analytic approach was developed to extract temperature from the frequencies of the measured signal within the flame brush region, where mixtures contain both burnt and unburnt gases. Mean product temperatures are shown to be 8% lower than the adiabatic temperatures for the nominal equivalence ratio, and 14% higher than measurements made with a thermocouple, uncorrected for radiation losses. This work represents the first application of LIGS to a high-pressure, turbulent swirling flame, opening up the potential for future uses in other real-world applications. Challenges associated with the deployment of the technique are described as are potential measures to overcome these difficulties.
- 12 January 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (5) , 1-12
Spatial Temperature and Water Molar Concentration Measurements Using Thermal and Electrostrictive Laser-Induced Grating Spectroscopy During Operation of a Swirl Burner at Pressure
Laser-Induced Grating Spectroscopy (LIGS) was applied in a high-pressure combustion facility. Instantaneous (sub-μs), spatially resolved (within 5 mm) measurements of temperature and molar fractions of water were obtained using thermal and electrostrictive LIGS signals. Temperatures up to 1800 K and water molar fractions between 0.01 and 0.12 were measured. A new analytic approach was developed to extract temperature from the frequencies of the measured signal within the flame brush region, where mixtures contain both burnt and unburnt gases. Mean product temperatures are shown to be 8% lower than the adiabatic temperatures for the nominal equivalence ratio, and 14% higher than measurements made with a thermocouple, uncorrected for radiation losses. This work represents the first application of LIGS to a high-pressure, turbulent swirling flame, opening up the potential for future uses in other real-world applications. Challenges associated with the deployment of the technique are described as are potential measures to overcome these difficulties.
- 4 January 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (6) , 1-12
Influence of Variable Swirl on Emissions in a Non-Premixed Fuel-Flexible Burner at Elevated Ambient Conditions
As alternative fuels are designated for future energy applications, flexible combustor designs require considerable development to ensure stable operation with reduced NOx emissions. A non-premixed variable swirl burner was used to experimentally appraise changes in NO production pathways, with CH4 NH3, and H2 flames, alongside intermediate fuel blends. Maintaining an equivalent thermal power and flame temperature between fuels, preheated reactants (500 K) were supplied to the burner, with parametric changes made to pressure (1 - 6 bara) and swirl number (0.8 - 2.0). NO production was characterized, alongside variations in flame structure and topology, with a correlation demonstrated for exhaust emissions. NO production was shown to be sensitive to combustor pressure, providing an expected increase for CH4 and H2 flames. Emission profiles from both NH3 and H2 flames are shown to be significantly augmented by a change in swirl number. As NH3 fractions were increased in the H2 blend, a decaying trend in NO emissions was observed with an increase in pressure, and as a function of mixture ratio. However, this behaviour was markedly augmented by a change in swirl number and suggests that further reductions may be possible at increased pressure. At the low swirl/high pressure condition the NH3/H2 blend outperformed pure H2, providing lower NO concentrations. Emissions data were normalised using the traditional dry/O2 correction, alongside mass scaled by thermal power, with a comparison provided. The corresponding differences in emission formation pathways were investigated, alongside high-speed OH* chemiluminescence to further elucidate findings.
- 4 January 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (6) , 1-12
Influence of Variable Swirl on Emissions in a Non-Premixed Fuel-Flexible Burner at Elevated Ambient Conditions
As alternative fuels are designated for future energy applications, flexible combustor designs require considerable development to ensure stable operation with reduced NOx emissions. A non-premixed variable swirl burner was used to experimentally appraise changes in NO production pathways, with CH4 NH3, and H2 flames, alongside intermediate fuel blends. Maintaining an equivalent thermal power and flame temperature between fuels, preheated reactants (500 K) were supplied to the burner, with parametric changes made to pressure (1 - 6 bara) and swirl number (0.8 - 2.0). NO production was characterized, alongside variations in flame structure and topology, with a correlation demonstrated for exhaust emissions. NO production was shown to be sensitive to combustor pressure, providing an expected increase for CH4 and H2 flames. Emission profiles from both NH3 and H2 flames are shown to be significantly augmented by a change in swirl number. As NH3 fractions were increased in the H2 blend, a decaying trend in NO emissions was observed with an increase in pressure, and as a function of mixture ratio. However, this behaviour was markedly augmented by a change in swirl number and suggests that further reductions may be possible at increased pressure. At the low swirl/high pressure condition the NH3/H2 blend outperformed pure H2, providing lower NO concentrations. Emissions data were normalised using the traditional dry/O2 correction, alongside mass scaled by thermal power, with a comparison provided. The corresponding differences in emission formation pathways were investigated, alongside high-speed OH* chemiluminescence to further elucidate findings.
- Open Access
- 16 July 2021
- Published by ASME International
Emissions Performance of Staged Premixed and Diffusion Combustor Concepts for an NH3/Air Flame With and Without Reactant Humidification
*Renewably generated NH~3~ offers a form of carbon-free chemical energy storage to meet the differences between uncertain renewable supply and fluctuating demand, and has the potential to support future energy requirements as a power-to-X concept. The storage and transportation characteristics of NH~3~ are favorable compared with H~2~, however there are significant combustion
- 16 July 2021
- Published by ASME International
Open AccessEmissions Performance of Staged Premixed and Diffusion Combustor Concepts for an NH3/Air Flame With and Without Reactant Humidification
*Renewably generated NH~3~ offers a form of carbon-free chemical energy storage to meet the differences between uncertain renewable supply and fluctuating demand, and has the potential to support future energy requirements as a power-to-X concept. The storage and transportation characteristics of NH~3~ are favorable compared with H~2~, however there are significant combustion
- Open Access
- 16 July 2021
- Published by ASME International
Experimental and Kinetic Evaluation of Pressurized Lean Premixed Hydrogen-Air Flame Stability With Carbon Dioxide and Steam Dilution
The potential for aligning industrial processes, such as steam-methane reforming for large-scale hydrogen production, with carbon capture and storage provides three unique vectors (hydrogen, carbon dioxide, and steam) for utilization in decarbonized gas turbine power generation, considering both new hydrogen-fired gas turbines and retrofit of existing industrial gas turbine fleet.
- 16 July 2021
- Published by ASME International
Open AccessExperimental and Kinetic Evaluation of Pressurized Lean Premixed Hydrogen-Air Flame Stability With Carbon Dioxide and Steam Dilution
The potential for aligning industrial processes, such as steam-methane reforming for large-scale hydrogen production, with carbon capture and storage provides three unique vectors (hydrogen, carbon dioxide, and steam) for utilization in decarbonized gas turbine power generation, considering both new hydrogen-fired gas turbines and retrofit of existing industrial gas turbine fleet.
- 1 February 2021
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Waste and Resource Management
- Vol. 174 (1) , 3-11
A waste heat recovery strategy and its deployment: an integrated steelworks case study
Steelmaking is energy intensive, with manufacturing facilities representing some of the biggest point-source carbon dioxide (CO2) emitters in the UK. Efficiency improvements are essential with rising energy costs, driving significant investment from the UK iron and steel sector. However, the industry still finds it difficult to justify waste heat recovery (WHR) projects, as individual schemes incorporating waste heat capture and an end-use for the waste heat often incur high capital costs, resulting in long payback times. This paper describes the conceptual and numerical development of a strategy for the deployment of WHR using a large integrated steel works as a case study. An existing asset was utilised to link individual waste heat schemes together with a single end-user; thereby reducing the capital requirement for each subsequent project. The proposed strategy and its development is discussed, followed by the resultant carbon dioxide and energy savings (estimated to be 2.3 Mt and equivalent to £45 million), over the 6-year period since its implementation.
- 1 February 2021
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Waste and Resource Management
- Vol. 174 (1) , 3-11
A waste heat recovery strategy and its deployment: an integrated steelworks case study
Steelmaking is energy intensive, with manufacturing facilities representing some of the biggest point-source carbon dioxide (CO2) emitters in the UK. Efficiency improvements are essential with rising energy costs, driving significant investment from the UK iron and steel sector. However, the industry still finds it difficult to justify waste heat recovery (WHR) projects, as individual schemes incorporating waste heat capture and an end-use for the waste heat often incur high capital costs, resulting in long payback times. This paper describes the conceptual and numerical development of a strategy for the deployment of WHR using a large integrated steel works as a case study. An existing asset was utilised to link individual waste heat schemes together with a single end-user; thereby reducing the capital requirement for each subsequent project. The proposed strategy and its development is discussed, followed by the resultant carbon dioxide and energy savings (estimated to be 2.3 Mt and equivalent to £45 million), over the 6-year period since its implementation.
- Open Access
- 4 February 2020
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (4)
Characterization of Additive Layer Manufacturing Swirl Burner Surface Roughness and Its Effects on Flame Stability Using High-Speed Diagnostics
In this study, two Inconel 625 swirl nozzle inserts with identical bulk geometry were constructed via additive layer manufacturing (ALM) for use in a generic gas turbine swirl burner. Further postprocessing by grit blasting of one swirl nozzle insert results in a quantifiable change to the surface roughness characteristics when compared with the unprocessed ALM swirl nozzle insert or a third nozzle insert which has been manufactured using traditional machining methods. An evaluation of the influence of variable surface roughness effects from these swirl nozzle inserts is therefore performed under preheated isothermal and combustion conditions for premixed methane-air flames at thermal power of 25 kW. High-speed velocimetry at the swirler exit under isothermal conditions gives evidence of the change in near-wall boundary layer thickness and turbulent fluctuations resulting from the change in nozzle surface roughness. Under atmospheric combustion conditions, this influence is further quantified using a combination of dynamic pressure, high-speed OH* chemiluminescence, and exhaust gas emissions measurements to evaluate the flame stabilization mechanisms at the lean blowoff and rich stability limits. Notable differences in flame stabilization are evident as the surface roughness is varied, and changes in rich stability limit were investigated in relation to changes in the near-wall turbulence intensity. Results show that precise control of in-process or postprocess surface roughness of wetted surfaces can positively influence burner stability limits and NOx emissions and must, therefore, be carefully considered in the ALM burner design process as well as computational fluid dynamics (CFD) models.
- 4 February 2020
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (4)
Open AccessCharacterization of Additive Layer Manufacturing Swirl Burner Surface Roughness and Its Effects on Flame Stability Using High-Speed Diagnostics
In this study, two Inconel 625 swirl nozzle inserts with identical bulk geometry were constructed via additive layer manufacturing (ALM) for use in a generic gas turbine swirl burner. Further postprocessing by grit blasting of one swirl nozzle insert results in a quantifiable change to the surface roughness characteristics when compared with the unprocessed ALM swirl nozzle insert or a third nozzle insert which has been manufactured using traditional machining methods. An evaluation of the influence of variable surface roughness effects from these swirl nozzle inserts is therefore performed under preheated isothermal and combustion conditions for premixed methane-air flames at thermal power of 25 kW. High-speed velocimetry at the swirler exit under isothermal conditions gives evidence of the change in near-wall boundary layer thickness and turbulent fluctuations resulting from the change in nozzle surface roughness. Under atmospheric combustion conditions, this influence is further quantified using a combination of dynamic pressure, high-speed OH* chemiluminescence, and exhaust gas emissions measurements to evaluate the flame stabilization mechanisms at the lean blowoff and rich stability limits. Notable differences in flame stabilization are evident as the surface roughness is varied, and changes in rich stability limit were investigated in relation to changes in the near-wall turbulence intensity. Results show that precise control of in-process or postprocess surface roughness of wetted surfaces can positively influence burner stability limits and NOx emissions and must, therefore, be carefully considered in the ALM burner design process as well as computational fluid dynamics (CFD) models.
- 17 June 2019
- Published by ASME International
Characterization of ALM Swirl Burner Surface Roughness and its Effects on Flame Stability Using High-Speed Diagnostics
The use of metallic Additive Layer Manufacturing (ALM) is an active area of development for gas turbine components, particularly concerning novel combustor prototypes for micro gas turbines. However, further study is required to understand the influence of this manufacturing technique and subsequent post-processing on the resulting burner component surface roughness and its effect on flame stability. In this study, two Inconel 625 swirl nozzle inserts with identical bulk geometry (swirl number, Sg = 0.8) were constructed via ALM for use in a generic gas turbine swirl burner. Further post-processing by grit blasting of one swirl nozzle insert results in a quantifiable change to the surface roughness characteristics in the burner exit nozzle when compared with the unprocessed ALM swirl nozzle insert or a third nozzle insert which has been manufactured using traditional machining methods. An evaluation of the influence of variable surface roughness effects from these swirl nozzle inserts is therefore performed under preheated isothermal and combustion conditions for premixed methane-air flames at thermal power of 25 kW. High-speed velocimetry at the swirler exit under isothermal air flow conditions gives evidence of the change in near-wall boundary layer thickness and turbulent fluctuations resulting from the change in nozzle surface roughness. Under atmospheric combustion conditions, this influence is further quantified using a combination of dynamic pressure, high-speed OH* chemiluminescence, and exhaust gas emissions measurements to evaluate the flame stabilization mechanisms at the lean blowoff and rich stability limits. Notable differences in flame stabilization are evident as the surface roughness is varied, and changes in rich stability limit were investigated in relation to changes in the near-wall turbulence intensity. Results show the viability of using ALM swirl nozzles in lean premixed gas turbine combustion. Furthermore, precise control of in-process or post-process surface roughness of wetted surfaces can positively influence burner stability limits and must therefore be carefully considered in the ALM burner design process as well as CFD models.
- 17 June 2019
- Published by ASME International
Characterization of ALM Swirl Burner Surface Roughness and its Effects on Flame Stability Using High-Speed Diagnostics
The use of metallic Additive Layer Manufacturing (ALM) is an active area of development for gas turbine components, particularly concerning novel combustor prototypes for micro gas turbines. However, further study is required to understand the influence of this manufacturing technique and subsequent post-processing on the resulting burner component surface roughness and its effect on flame stability. In this study, two Inconel 625 swirl nozzle inserts with identical bulk geometry (swirl number, Sg = 0.8) were constructed via ALM for use in a generic gas turbine swirl burner. Further post-processing by grit blasting of one swirl nozzle insert results in a quantifiable change to the surface roughness characteristics in the burner exit nozzle when compared with the unprocessed ALM swirl nozzle insert or a third nozzle insert which has been manufactured using traditional machining methods. An evaluation of the influence of variable surface roughness effects from these swirl nozzle inserts is therefore performed under preheated isothermal and combustion conditions for premixed methane-air flames at thermal power of 25 kW. High-speed velocimetry at the swirler exit under isothermal air flow conditions gives evidence of the change in near-wall boundary layer thickness and turbulent fluctuations resulting from the change in nozzle surface roughness. Under atmospheric combustion conditions, this influence is further quantified using a combination of dynamic pressure, high-speed OH* chemiluminescence, and exhaust gas emissions measurements to evaluate the flame stabilization mechanisms at the lean blowoff and rich stability limits. Notable differences in flame stabilization are evident as the surface roughness is varied, and changes in rich stability limit were investigated in relation to changes in the near-wall turbulence intensity. Results show the viability of using ALM swirl nozzles in lean premixed gas turbine combustion. Furthermore, precise control of in-process or post-process surface roughness of wetted surfaces can positively influence burner stability limits and must therefore be carefully considered in the ALM burner design process as well as CFD models.
- Top Cited PapersOpen Access
- 1 January 2019
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 37 (4) , 5401-5409
Influence of steam addition and elevated ambient conditions on NOx reduction in a staged premixed swirling NH3/H2 flame
- 1 January 2019
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 37 (4) , 5401-5409
Top Cited PapersOpen AccessInfluence of steam addition and elevated ambient conditions on NOx reduction in a staged premixed swirling NH3/H2 flame