Sergey Zadvorkin
Sergey Zadvorkin has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Eduard S. Gorkunov
Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences, 34 Komsomolskaya St., Ekaterinburg, 620049, Russia
8 shared publications - Evgeniia Putilova
Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences, Yekaterinburg, Russia
5 shared publications - Александр Николаевич Мушников
Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences
5 shared publications - Dmitrii I. Vichuzhanin
Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences, Ekaterinburg, Russian Federation
4 shared publications E. S. Gorkunov
Institute of Engineering Science UrB RAS, Ekaterinburg, 620049 Russia
4 shared publications- Larisa S. Goruleva
Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences
4 shared publications
Latest Publications
- Open Access
- 1 April 2025
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2025 (2) , 42-59
MICROSTRUCTURE, RESIDUAL STRESSES, TEXTURE, AND MECHANICAL PROPERTIES OF A WELDED JOINT IN VT1-0 ALLOY SHEETS
The grain structure, microstrain distribution, crystallographic texture and residual stresses in a CO2 laser welded joint of VT1-0 alloy sheets (technical titanium) are studied by EBSD and X-ray diffraction analysis. The mechanical properties of the welded joint are determined. It is shown that the weld structure is represented by differently directed large laths of the α-phase. The metal in the heat-affected zones is characterized by a mixed structure resulting from the polymorphic β→α transformation in the form of packets of secondary α-phase plates near the weld and polyhedral α-grains near the base metal. Multicomponent textures have been detected in all the zones of the welded joint. This creates prerequisites for decreased anisotropy of strength properties, which is typical of hexagonal crystals. The strength of the welded joint proves to be significantly higher than that of the base metal; namely, the ultimate strength of the joint is 660 MPa, and that of the base material is 500 MPa. The heat-affected zone is the most deformed zone in the welded joint, the share of deformed grains reaches 44%, and residual stresses do not exceed 10% of the yield strength.
- 1 April 2025
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2025 (2) , 42-59
Open AccessMICROSTRUCTURE, RESIDUAL STRESSES, TEXTURE, AND MECHANICAL PROPERTIES OF A WELDED JOINT IN VT1-0 ALLOY SHEETS
The grain structure, microstrain distribution, crystallographic texture and residual stresses in a CO2 laser welded joint of VT1-0 alloy sheets (technical titanium) are studied by EBSD and X-ray diffraction analysis. The mechanical properties of the welded joint are determined. It is shown that the weld structure is represented by differently directed large laths of the α-phase. The metal in the heat-affected zones is characterized by a mixed structure resulting from the polymorphic β→α transformation in the form of packets of secondary α-phase plates near the weld and polyhedral α-grains near the base metal. Multicomponent textures have been detected in all the zones of the welded joint. This creates prerequisites for decreased anisotropy of strength properties, which is typical of hexagonal crystals. The strength of the welded joint proves to be significantly higher than that of the base metal; namely, the ultimate strength of the joint is 660 MPa, and that of the base material is 500 MPa. The heat-affected zone is the most deformed zone in the welded joint, the share of deformed grains reaches 44%, and residual stresses do not exceed 10% of the yield strength.
- Open Access
- 1 December 2023
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2023 (6) , 132-144
An experimental and computational study of through-depth strain distribution during frictional treatment of a metastable austenitic steel
An Experimental and Computational Study of Through-Depth Strain Distribution During Frictional Treatment of a Metastable Austenitic Steel / L. S. Goruleva, S. M. Zadvorkin, D. I. Vichuzhanin, R. A. Savrai, P. A. Skorynina // Diagnostics, Resource and Mechanics of materials and structures.- 2023 - Iss. 6.
- 1 December 2023
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2023 (6) , 132-144
Open AccessAn experimental and computational study of through-depth strain distribution during frictional treatment of a metastable austenitic steel
An Experimental and Computational Study of Through-Depth Strain Distribution During Frictional Treatment of a Metastable Austenitic Steel / L. S. Goruleva, S. M. Zadvorkin, D. I. Vichuzhanin, R. A. Savrai, P. A. Skorynina // Diagnostics, Resource and Mechanics of materials and structures.- 2023 - Iss. 6.
- Open Access
- 1 December 2023
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2023 (6) , 45-64
Application of microindentation to the evaluation of strain distribution over the section of extruded aluminum alloy bars
The paper proposes to supplement the monitoring of strain uniformity over the cross-section of extruded aluminum alloy bars, based on the macro- and microstructure in the central part, at ½ radius, and in the surface zone in several cross-sections along the length of press products, with microindentation of these sections. For this purpose, the microstructure, the loading diagram, and the pattern of the distribution of micromechanical properties across the cross-section of extruded bars made of the AD33 and D16 aluminum alloys are comparatively analyzed. These alloys differ in that in one alloy, AD33, the alloying elements strengthen the aluminum-based solid solution without forming independent phases, and in the other, D16, they form strengthening intermetallic compounds Al2CuMg. The microhardness of the AD33 alloy is ~55 HV 0.1, that of the D16 alloy being 120 HV 0.1. The alloys differ in the distribution of micromechanical properties over both the transverse and longitudinal sections of the extruded bars. It has been found that maximum homogeneity is characteristic of the central part of the rods made of both alloys. The microindentation data correlate with the changes in the microstructure and the results of assessing the distribution of microstrains in the crystal lattice of an aluminum-based solid solution over the cross-section of extruded products by EBSD using recrystallization maps. This makes it possible to recommend the microindentation method for assessing the distribution of strains over the cross-section of extruded aluminum alloy bars.
- 1 December 2023
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2023 (6) , 45-64
Open AccessApplication of microindentation to the evaluation of strain distribution over the section of extruded aluminum alloy bars
The paper proposes to supplement the monitoring of strain uniformity over the cross-section of extruded aluminum alloy bars, based on the macro- and microstructure in the central part, at ½ radius, and in the surface zone in several cross-sections along the length of press products, with microindentation of these sections. For this purpose, the microstructure, the loading diagram, and the pattern of the distribution of micromechanical properties across the cross-section of extruded bars made of the AD33 and D16 aluminum alloys are comparatively analyzed. These alloys differ in that in one alloy, AD33, the alloying elements strengthen the aluminum-based solid solution without forming independent phases, and in the other, D16, they form strengthening intermetallic compounds Al2CuMg. The microhardness of the AD33 alloy is ~55 HV 0.1, that of the D16 alloy being 120 HV 0.1. The alloys differ in the distribution of micromechanical properties over both the transverse and longitudinal sections of the extruded bars. It has been found that maximum homogeneity is characteristic of the central part of the rods made of both alloys. The microindentation data correlate with the changes in the microstructure and the results of assessing the distribution of microstrains in the crystal lattice of an aluminum-based solid solution over the cross-section of extruded products by EBSD using recrystallization maps. This makes it possible to recommend the microindentation method for assessing the distribution of strains over the cross-section of extruded aluminum alloy bars.
- 30 October 2023
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 42 (4) , 1-7
Effect of Biaxial Tension on the Coercive Force of Low-Alloy Steel
- 30 October 2023
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 42 (4) , 1-7
Effect of Biaxial Tension on the Coercive Force of Low-Alloy Steel
- Open Access
- 1 February 2023
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2023 (1) , 24-40
Detection of prefracture zones in structural materials by magnetic and optical methods
The study of the applicability of magnetic and optical methods to the detection of prefracture zones under fatigue degradation of structural materials is exemplified by the 09G2S steel. The regularities of changes in the signal of an attached fluxgate gradiometer with the increasing number of loading cycles have been revealed; namely, significant changes in the gradiometer readings on individual specimen surface areas prove to result from the formation of fracture zones. The change in the value of the coefficient of correlation among the speckle images is studied at different stages of cyclic testing. Speckle image heterogeneity is shown to appear due to fracture nucleation. Thus, the applicability of magnetic and speckle-interferometric methods to detecting prefracture zones in objects under cyclic loading is substantiated.
- 1 February 2023
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2023 (1) , 24-40
Open AccessDetection of prefracture zones in structural materials by magnetic and optical methods
The study of the applicability of magnetic and optical methods to the detection of prefracture zones under fatigue degradation of structural materials is exemplified by the 09G2S steel. The regularities of changes in the signal of an attached fluxgate gradiometer with the increasing number of loading cycles have been revealed; namely, significant changes in the gradiometer readings on individual specimen surface areas prove to result from the formation of fracture zones. The change in the value of the coefficient of correlation among the speckle images is studied at different stages of cyclic testing. Speckle image heterogeneity is shown to appear due to fracture nucleation. Thus, the applicability of magnetic and speckle-interferometric methods to detecting prefracture zones in objects under cyclic loading is substantiated.
- Open Access
- 1 December 2022
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2022 (6) , 95-106
Effect of plastic deformation on the phase composition and electromagnetic characteristics of the 321N austenitic steel (08Kh18N10T)
The changes in the phase composition and electromagnetic properties of the 321N chromium-nickel austenitic steel under plastic deformation by uniaxial tension are studied. As strain increases from 0 to 0.37, the content of ferromagnetic α′-martensite in the steel increases monotonically to 60%. The electrical resistivity and the initial magnetic permeability increase monotonically by factors of 1,25 and 18, respectively. To monitor the strain state and the content of α'-martensite in products made of the 321N steel, it is preferable to use initial magnetic permeability rather than electrical resistance. The skin layer thickness of the deformed 321N steel for frequencies from 5 to 1000 kHz is calculated from the experimental values of initial magnetic permeability and electrical resistivity. Eddy current diagnostics of the state of the surface of products made of this steel, hardened by surface plastic deformation, is proposed to be performed at frequencies ranging between 100 and 200 kHz.
- 1 December 2022
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2022 (6) , 95-106
Open AccessEffect of plastic deformation on the phase composition and electromagnetic characteristics of the 321N austenitic steel (08Kh18N10T)
The changes in the phase composition and electromagnetic properties of the 321N chromium-nickel austenitic steel under plastic deformation by uniaxial tension are studied. As strain increases from 0 to 0.37, the content of ferromagnetic α′-martensite in the steel increases monotonically to 60%. The electrical resistivity and the initial magnetic permeability increase monotonically by factors of 1,25 and 18, respectively. To monitor the strain state and the content of α'-martensite in products made of the 321N steel, it is preferable to use initial magnetic permeability rather than electrical resistance. The skin layer thickness of the deformed 321N steel for frequencies from 5 to 1000 kHz is calculated from the experimental values of initial magnetic permeability and electrical resistivity. Eddy current diagnostics of the state of the surface of products made of this steel, hardened by surface plastic deformation, is proposed to be performed at frequencies ranging between 100 and 200 kHz.
- Open Access
- 1 October 2022
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2022 (5) , 40-49
Effect of friction treatment of the AISI 321 steel on changes in its hardness and magnetic characteristics
Putilova E. A., Goruleva L. S., Zadvorkin S. M. Effect of Frictional Treatment of the Aisi 321 Steel on the Change of Its Hardness and Magnetic Characteristics // Diagnostics, Resource and Mechanics of materials and structures.- 2022 - Iss. 5.
- 1 October 2022
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2022 (5) , 40-49
Open AccessEffect of friction treatment of the AISI 321 steel on changes in its hardness and magnetic characteristics
Putilova E. A., Goruleva L. S., Zadvorkin S. M. Effect of Frictional Treatment of the Aisi 321 Steel on the Change of Its Hardness and Magnetic Characteristics // Diagnostics, Resource and Mechanics of materials and structures.- 2022 - Iss. 5.
- Open Access
- 1 August 2022
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2022 (4) , 50-60
Experimental facility for studying the physical properties of materials in a plane stress state
An original experimental facility for studying the physical properties of materials during elastic-plastic deformation along two axes has been created. The facility has no ferromagnetic parts in the working area, thus enabling us to make more accurate magnetic measurements. Biaxial deformation is simulated by the finite element method in order to optimize the geometry of the specimen and to determine the stress state in the central zone of the specimen. Test experiments on the effect of biaxial tension on the coercive force of the 12G2S are performed.
- 1 August 2022
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2022 (4) , 50-60
Open AccessExperimental facility for studying the physical properties of materials in a plane stress state
An original experimental facility for studying the physical properties of materials during elastic-plastic deformation along two axes has been created. The facility has no ferromagnetic parts in the working area, thus enabling us to make more accurate magnetic measurements. Biaxial deformation is simulated by the finite element method in order to optimize the geometry of the specimen and to determine the stress state in the central zone of the specimen. Test experiments on the effect of biaxial tension on the coercive force of the 12G2S are performed.
- 1 January 2022
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2509 (1) , 020097
Estimation of cyclic fracture toughness of promising 26KhMFA pipe steel in the interval of climatic temperatures
The paper presents the results of studying the characteristics of fracture resistance of promising 26KhMFA pipe steel in the range of climatic operating temperatures. It was found that the steel under the study has high indicators of both mechanical strength and resistance to fatigue crack propagation in the temperature range from +20 to −70°C. Studies of the phenomena accompanying the crack growth on the lateral surface of CT-specimens have been carried out. It is shown that with a drop in the test temperature, the area of the localized plastic deformation zone at the fatigue crack tip decreases with a simultaneous microhardness increase within this zone.
- 1 January 2022
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2509 (1) , 020097
Estimation of cyclic fracture toughness of promising 26KhMFA pipe steel in the interval of climatic temperatures
The paper presents the results of studying the characteristics of fracture resistance of promising 26KhMFA pipe steel in the range of climatic operating temperatures. It was found that the steel under the study has high indicators of both mechanical strength and resistance to fatigue crack propagation in the temperature range from +20 to −70°C. Studies of the phenomena accompanying the crack growth on the lateral surface of CT-specimens have been carried out. It is shown that with a drop in the test temperature, the area of the localized plastic deformation zone at the fatigue crack tip decreases with a simultaneous microhardness increase within this zone.
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia Structural Integrity
- Vol. 20, 4-8
Effect of cyclic loading on the magnetic behavior of hot-rolled pipe steel 08G2B
- 1 January 2019
- Published by Elsevier in Procedia Structural Integrity
- Vol. 20, 4-8
Open AccessEffect of cyclic loading on the magnetic behavior of hot-rolled pipe steel 08G2B