Manuela Battipede
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Manuela Battipede has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Piero Gili
Politecnico di Torino
11 shared publications - Alberto Brandl
Politecnico di Torino
4 shared publications - Angelo Lerro
Department of Mechanical and Aerospace Engineering, Polytechnic University of Turin, Turin, Italy
4 shared publications - Francesco De Vivo
Polytechnic of Turin
2 shared publications Marco Lando
Politecnico di Torino, 10129 Torino, Italy
2 shared publications- Alessio Vitali
Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy
1 shared publication
Latest Publications
- Open Access
- 17 October 2022
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 14 (1) , 103-114
Alternative procedure to verify the H–V diagram after external installations on helicopters
Certification of external installations on helicopters, for modifications for which CS27/29.865 is not applicable, often requires the showing of compliance of paragraph CS XX.79—limiting height-speed envelope—which might imply, ultimately, a certain degree of H–V testing. Due to the implications on safety during the investigation of the H–V curve, a preliminary analytical investigation is advisable, to understand whether H–V test can be drastically reduced. Analytical investigation, though, is usually based on the extensive use of simulation data, based on validated dynamic mathematical models, which are usually not available to the applicant. The authors recently proposed an alternative method, based on the analysis of a set of flight tests, which is meant to assess quantitatively the different phases of the physical/mechanical phenomena related to the emergency maneuver performed by the pilot as a consequence of a power loss, within or in the proximity of the H–V curve. More in details, the analysis of the autorotation phenomenology reveals that the maneuver is made up by different phases and dedicated tests have been proposed to assess each of these phases. The whole test campaign is hence meant to gain a thorough insight of how, and specifically in which part of the maneuver, the external modification could affect the helicopter H–V characteristic. Depending on this substantiation, H–V testing can be avoided or drastically reduced, limiting the investigation to a few meaningful points. The proposed method has been recently assessed on an external basket installation, making use of purposely developed Flight Instrumentation and post-processing tools. More in details, results and conclusions are based on the analysis of static and dynamic flight parameters, acquired with a non-intrusive Flight Test Instrumentation, which monitors and correlates cockpit parameters and flight commands, following a back-to-back approach (i.e., pre- and post-modification). The method demonstrated was witnessed by EASA and found acceptable as an alternative method for showing of compliance to the applicable requirements.
- 17 October 2022
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 14 (1) , 103-114
Open AccessAlternative procedure to verify the H–V diagram after external installations on helicopters
Certification of external installations on helicopters, for modifications for which CS27/29.865 is not applicable, often requires the showing of compliance of paragraph CS XX.79—limiting height-speed envelope—which might imply, ultimately, a certain degree of H–V testing. Due to the implications on safety during the investigation of the H–V curve, a preliminary analytical investigation is advisable, to understand whether H–V test can be drastically reduced. Analytical investigation, though, is usually based on the extensive use of simulation data, based on validated dynamic mathematical models, which are usually not available to the applicant. The authors recently proposed an alternative method, based on the analysis of a set of flight tests, which is meant to assess quantitatively the different phases of the physical/mechanical phenomena related to the emergency maneuver performed by the pilot as a consequence of a power loss, within or in the proximity of the H–V curve. More in details, the analysis of the autorotation phenomenology reveals that the maneuver is made up by different phases and dedicated tests have been proposed to assess each of these phases. The whole test campaign is hence meant to gain a thorough insight of how, and specifically in which part of the maneuver, the external modification could affect the helicopter H–V characteristic. Depending on this substantiation, H–V testing can be avoided or drastically reduced, limiting the investigation to a few meaningful points. The proposed method has been recently assessed on an external basket installation, making use of purposely developed Flight Instrumentation and post-processing tools. More in details, results and conclusions are based on the analysis of static and dynamic flight parameters, acquired with a non-intrusive Flight Test Instrumentation, which monitors and correlates cockpit parameters and flight commands, following a back-to-back approach (i.e., pre- and post-modification). The method demonstrated was witnessed by EASA and found acceptable as an alternative method for showing of compliance to the applicable requirements.
- Open Access
Multi-Objective and Multi-Phase 4D Trajectory Optimization for Climate Mitigation-Oriented Flight Planning
Aviation contribution to global warming and anthropogenic climate change is increasing every year. To reverse this trend, it is crucial to identify greener alternatives to current aviation technologies and paradigms. Research in aircraft operations can provide a swift response to new environmental requirements, being easier to exploit on current fleets. This paper presents the development of a multi-objective and multi-phase 4D trajectory optimization tool to be integrated within a Flight Management System of a commercial aircraft capable of performing 4D trajectory tracking in a Free Route Airspace context. The optimization algorithm is based on a Chebyshev pseudospectral method, adapted to perform a multi-objective optimization with the two objectives being the Direct Operating Cost and the climate cost of a climb-cruise-descent trajectory. The climate cost function applies the Global Warming Potential metric to derive a comprehensive cost index that includes the climate forcing produced by CO2 and non-CO2 emissions, and by the formation of aircraft-induced clouds. The output of the optimization tool is a set of Pareto-optimal 4D trajectories among which the aircraft operator can choose the best solution that satisfies both its economic and environmental goals.
Open AccessMulti-Objective and Multi-Phase 4D Trajectory Optimization for Climate Mitigation-Oriented Flight Planning
Aviation contribution to global warming and anthropogenic climate change is increasing every year. To reverse this trend, it is crucial to identify greener alternatives to current aviation technologies and paradigms. Research in aircraft operations can provide a swift response to new environmental requirements, being easier to exploit on current fleets. This paper presents the development of a multi-objective and multi-phase 4D trajectory optimization tool to be integrated within a Flight Management System of a commercial aircraft capable of performing 4D trajectory tracking in a Free Route Airspace context. The optimization algorithm is based on a Chebyshev pseudospectral method, adapted to perform a multi-objective optimization with the two objectives being the Direct Operating Cost and the climate cost of a climb-cruise-descent trajectory. The climate cost function applies the Global Warming Potential metric to derive a comprehensive cost index that includes the climate forcing produced by CO2 and non-CO2 emissions, and by the formation of aircraft-induced clouds. The output of the optimization tool is a set of Pareto-optimal 4D trajectories among which the aircraft operator can choose the best solution that satisfies both its economic and environmental goals.
- Open Access
- 1 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 3127
Safety Analysis of a Certifiable Air Data System Based on Synthetic Sensors for Flow Angle Estimation
This work deals with the safety analysis of an air data system (ADS) partially based on synthetic sensors. The ADS is designed for the small aircraft transportation (SAT) community and is suitable for future unmanned aerial vehicles and urban air mobility applications. The ADS’s main innovation is based on estimation of the flow angles (angle-of-attack and angle-of-sideslip) using synthetic sensors instead of classical vanes (or sensors), whereas pressure and temperature are directly measured with Pitot and temperature probes. As the air data system is a safety-critical system, safety analyses are performed and the results are compared with the safety objectives required by the aircraft integrator. The present paper introduces the common aeronautical procedures for system safety assessment applied to a safety critical system partially based on synthetic sensors. The mean time between failures of ADS’s sub-parts are estimated on a statistical basis in order to evaluate the failure rate of the ADS’s functions. The proposed safety analysis is also useful in identifying the most critical air data system parts and sub-parts. Possible technological gaps to be filled to achieve the airworthiness safety objectives with nonredundant architectures are also identified.
- 1 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 3127
Open AccessSafety Analysis of a Certifiable Air Data System Based on Synthetic Sensors for Flow Angle Estimation
This work deals with the safety analysis of an air data system (ADS) partially based on synthetic sensors. The ADS is designed for the small aircraft transportation (SAT) community and is suitable for future unmanned aerial vehicles and urban air mobility applications. The ADS’s main innovation is based on estimation of the flow angles (angle-of-attack and angle-of-sideslip) using synthetic sensors instead of classical vanes (or sensors), whereas pressure and temperature are directly measured with Pitot and temperature probes. As the air data system is a safety-critical system, safety analyses are performed and the results are compared with the safety objectives required by the aircraft integrator. The present paper introduces the common aeronautical procedures for system safety assessment applied to a safety critical system partially based on synthetic sensors. The mean time between failures of ADS’s sub-parts are estimated on a statistical basis in order to evaluate the failure rate of the ADS’s functions. The proposed safety analysis is also useful in identifying the most critical air data system parts and sub-parts. Possible technological gaps to be filled to achieve the airworthiness safety objectives with nonredundant architectures are also identified.
- Open Access
A Data-Driven Approach to Identify Flight Test Data Suitable to Design Angle of Attack Synthetic Sensor for Flight Control Systems
Digital avionic solutions enable advanced flight control systems to be available also on smaller aircraft. One of the safety-critical segments is the air data system. Innovative architectures allow the use of synthetic sensors that can introduce significant technological and safety advances. The application to aerodynamic angles seems the most promising towards certified applications. In this area, the best procedures concerning the design of synthetic sensors are still an open question within the field. An example is given by the MIDAS project funded in the frame of Clean Sky 2. This paper proposes two data-driven methods that allow to improve performance over the entire flight envelope with particular attention to steady state flight conditions. The training set obtained is considerably undersized with consequent reduction of computational costs. These methods are validated with a real case and they will be used as part of the MIDAS life cycle. The first method, called Data-Driven Identification and Generation of Quasi-Steady States (DIGS), is based on the (i) identification of the lift curve of the aircraft; (ii) augmentation of the training set with artificial flight data points. DIGS’s main aim is to reduce the issue of unbalanced training set. The second method, called Similar Flight Test Data Pruning (SFDP), deals with data reduction based on the isolation of quasi-unique points. Results give an evidence of the validity of the methods for the MIDAS project that can be easily adopted for generic synthetic sensor design for flight control system applications.
Open AccessA Data-Driven Approach to Identify Flight Test Data Suitable to Design Angle of Attack Synthetic Sensor for Flight Control Systems
Digital avionic solutions enable advanced flight control systems to be available also on smaller aircraft. One of the safety-critical segments is the air data system. Innovative architectures allow the use of synthetic sensors that can introduce significant technological and safety advances. The application to aerodynamic angles seems the most promising towards certified applications. In this area, the best procedures concerning the design of synthetic sensors are still an open question within the field. An example is given by the MIDAS project funded in the frame of Clean Sky 2. This paper proposes two data-driven methods that allow to improve performance over the entire flight envelope with particular attention to steady state flight conditions. The training set obtained is considerably undersized with consequent reduction of computational costs. These methods are validated with a real case and they will be used as part of the MIDAS life cycle. The first method, called Data-Driven Identification and Generation of Quasi-Steady States (DIGS), is based on the (i) identification of the lift curve of the aircraft; (ii) augmentation of the training set with artificial flight data points. DIGS’s main aim is to reduce the issue of unbalanced training set. The second method, called Similar Flight Test Data Pruning (SFDP), deals with data reduction based on the isolation of quasi-unique points. Results give an evidence of the validity of the methods for the MIDAS project that can be easily adopted for generic synthetic sensor design for flight control system applications.
- Open Access
Preliminary Design of a Model-Free Synthetic Sensor for Aerodynamic Angle Estimation for Commercial Aviation
Heterogeneity of the small aircraft category (e.g., small air transport (SAT), urban air mobility (UAM), unmanned aircraft system (UAS)), modern avionic solution (e.g., fly-by-wire (FBW)) and reduced aircraft (A/C) size require more compact, integrated, digital and modular air data system (ADS) able to measure data from the external environment. The MIDAS project, funded in the frame of the Clean Sky 2 program, aims to satisfy those recent requirements with an ADS certified for commercial applications. The main pillar lays on a smart fusion between COTS solutions and analytical sensors (patented technology) for the identification of the aerodynamic angles. The identification involves both flight dynamic relationships and data-driven state observer(s) based on neural techniques, which are deterministic once the training is completed. As this project will bring analytical sensors on board of civil aircraft as part of a redundant system for the very first time, design activities documented in this work have a particular focus on airworthiness certification aspects. At this maturity level, simulated data are used, real flight test data will be used in the next stages. Data collection is described both for the training and test aspects. Training maneuvers are defined aiming to excite all dynamic modes, whereas test maneuvers are collected aiming to validate results independently from the training set and all autopilot configurations. Results demonstrate that an alternate solution is possible enabling significant savings in terms of computational effort and lines of codes but they show, at the same time, that a better training strategy may be beneficial to cope with the new neural network architecture.
Open AccessPreliminary Design of a Model-Free Synthetic Sensor for Aerodynamic Angle Estimation for Commercial Aviation
Heterogeneity of the small aircraft category (e.g., small air transport (SAT), urban air mobility (UAM), unmanned aircraft system (UAS)), modern avionic solution (e.g., fly-by-wire (FBW)) and reduced aircraft (A/C) size require more compact, integrated, digital and modular air data system (ADS) able to measure data from the external environment. The MIDAS project, funded in the frame of the Clean Sky 2 program, aims to satisfy those recent requirements with an ADS certified for commercial applications. The main pillar lays on a smart fusion between COTS solutions and analytical sensors (patented technology) for the identification of the aerodynamic angles. The identification involves both flight dynamic relationships and data-driven state observer(s) based on neural techniques, which are deterministic once the training is completed. As this project will bring analytical sensors on board of civil aircraft as part of a redundant system for the very first time, design activities documented in this work have a particular focus on airworthiness certification aspects. At this maturity level, simulated data are used, real flight test data will be used in the next stages. Data collection is described both for the training and test aspects. Training maneuvers are defined aiming to excite all dynamic modes, whereas test maneuvers are collected aiming to validate results independently from the training set and all autopilot configurations. Results demonstrate that an alternate solution is possible enabling significant savings in terms of computational effort and lines of codes but they show, at the same time, that a better training strategy may be beneficial to cope with the new neural network architecture.
- Open Access
- 5 July 2017
- Published by MDPI AG in Electronics
- Vol. 6 (3) , 50
Risk Analysis of the Future Implementation of a Safety Management System for Multiple RPAS Based on First Demonstration Flights
The modern aeronautical scenario has welcomed the massive diffusion of new key elements, including the Remote Piloted Aircraft Systems (RPAS), initially used for military purposes only. The current decade has seen RPAS ready to become a new airspace user in a large variety of civilian applications. Although RPAS can currently only be flown into segregated airspaces, due to national and international Flight Aviation Authorities′ (FAAs) constraints, they represent a remarkable potential growth in terms of development and economic investments for aviation. Full RPAS development will only happen when flight into non-segregated airspaces is authorized, as for manned civil and military aircraft. The preliminary requirement for disclosing the airspace to RPAS is the implementation of an ad hoc Safety Management System (SMS), as prescribed by ICAO, for every aeronautical operator. This issue arises in the context of the ongoing restructuring of airspaces management, according to SESAR-JU in Europe and NextGen in the USA (SESAR-JU has defined how RPAS research should be conducted in SESAR 2020, all in accordance with the 2015 European ATM Master Plan). This paper provides the basis to implement a risk model and general procedures/methodologies to investigate RPAS safety, according to the operational scenarios defined by EASA (European Aviation Safety Agency). The study is based on results achieved by multiple-RPAS experimental flights, performed within the RAID (RPAS-ATM Integration Demonstration) project.
- 5 July 2017
- Published by MDPI AG in Electronics
- Vol. 6 (3) , 50
Open AccessRisk Analysis of the Future Implementation of a Safety Management System for Multiple RPAS Based on First Demonstration Flights
The modern aeronautical scenario has welcomed the massive diffusion of new key elements, including the Remote Piloted Aircraft Systems (RPAS), initially used for military purposes only. The current decade has seen RPAS ready to become a new airspace user in a large variety of civilian applications. Although RPAS can currently only be flown into segregated airspaces, due to national and international Flight Aviation Authorities′ (FAAs) constraints, they represent a remarkable potential growth in terms of development and economic investments for aviation. Full RPAS development will only happen when flight into non-segregated airspaces is authorized, as for manned civil and military aircraft. The preliminary requirement for disclosing the airspace to RPAS is the implementation of an ad hoc Safety Management System (SMS), as prescribed by ICAO, for every aeronautical operator. This issue arises in the context of the ongoing restructuring of airspaces management, according to SESAR-JU in Europe and NextGen in the USA (SESAR-JU has defined how RPAS research should be conducted in SESAR 2020, all in accordance with the 2015 European ATM Master Plan). This paper provides the basis to implement a risk model and general procedures/methodologies to investigate RPAS safety, according to the operational scenarios defined by EASA (European Aviation Safety Agency). The study is based on results achieved by multiple-RPAS experimental flights, performed within the RAID (RPAS-ATM Integration Demonstration) project.
- 15 February 2017
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 88 (3) , 1987
Erratum to: Joseph covariance formula adaptation to Square-Root Sigma-Point Kalman filters
- 15 February 2017
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 88 (3) , 1987
Erratum to: Joseph covariance formula adaptation to Square-Root Sigma-Point Kalman filters
- 28 January 2017
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 88 (3) , 1969-1986
Joseph covariance formula adaptation to Square-Root Sigma-Point Kalman filters
- 28 January 2017
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 88 (3) , 1969-1986
Joseph covariance formula adaptation to Square-Root Sigma-Point Kalman filters
- 1 October 2015
- Published by Elsevier in Acta Astronautica
- Vol. 115, 338-348
Performances of a small hypersonic airplane (HyPlane)
- 1 October 2015
- Published by Elsevier in Acta Astronautica
- Vol. 115, 338-348
Performances of a small hypersonic airplane (HyPlane)
- 13 March 2013
- Published by Springer Nature in Journal of Intelligent & Robotic Systems
- Vol. 72 (1) , 123-144
Structural and Aerodynamics Analysis on Different Architectures for the Elettra Twin Flyer Prototype
- 13 March 2013
- Published by Springer Nature in Journal of Intelligent & Robotic Systems
- Vol. 72 (1) , 123-144
Structural and Aerodynamics Analysis on Different Architectures for the Elettra Twin Flyer Prototype