Cagdas Bilici
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cagdas Bilici has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Nina Stark
Virginia Polytechnic Institute and State University
4 shared publications- Nina Stark
Associate Professor, Dept. of Civil and Environmental Engineering, Virginia Tech., 200 Patton Hall, Blacksburg, VA 24061. ORCID:
2 shared publications Ali Albatal
Dept. of Civil and Environmental Engineering, Virginia Tech., 200 Patton Hall, Blacksburg, VA 24061.
1 shared publication- Ali Albatal
The Charles Edward Via, Jr. Department of Civil and Environmental Engineering Virginia Tech Blacksburg Virginia
1 shared publication - Carl T. Friedrichs
Chesapeake Bay National Estuarine Research Reserve in Virginia, Virginia Institute of Marine Science, Gloucester, USA
1 shared publication Dennis K. Kiptoo
Dept. of Civil and Environmental Engineering, Virginia Tech., 200 Patton Hall, Blacksburg, VA 24061.
1 shared publication
Latest Publications
- 27 April 2019
- Published by Springer Nature in Geo-Marine Letters
- Vol. 39 (3) , 175-189
Coupled sedimentological and geotechnical data analysis of surficial sediment layer characteristics in a tidal estuary
- 27 April 2019
- Published by Springer Nature in Geo-Marine Letters
- Vol. 39 (3) , 175-189
Coupled sedimentological and geotechnical data analysis of surficial sediment layer characteristics in a tidal estuary
- 21 March 2019
- Published by American Society of Civil Engineers (ASCE)
- p. 71-80
Uppermost Subaqueous Soil Variability in Front of the Situk River Inlet, Alaska, from Portable Free Fall Penetrometer
Nearshore areas in front of river inlets feature significant spatial and temporal variations in sediment distribution, transport, and deposition processes. This makes subaqueous sediment characterization of such locations essential for engineering applications and for the fundamental understanding of regional geomorphodynamics. Site investigation was conducted in the nearshore area off the Situk River Inlet, Yakutat, Alaska. This region is characterized by highly variable sediments and energetic wave conditions. In situ tests were conducted along ten cross shore transects with 64 locations in total using a portable free fall penetrometer. The results showed the presence of a loose sediment top layer of 3.8–6.9 cm in thickness overlying a stiffer stratum with a maximum quasi-static bearing capacity ranging from 30–106 kPa at sediment depths of less than 15 cm. More variability in sediment strength was observed with decreasing water depths (approaching the shore), and sediment strength generally somewhat decreased seaward. For transects closer to the inlet, a more distinct trend of decreasing sediment strength with distance to the shore was observed. As expected, the impact of waves on the sediments appeared significant in shallow water depths. The results suggested an influence of hydrodynamics and the presence of the inlet on the topmost sediment layers, and consequently on the geotechnical characteristics.
- 21 March 2019
- Published by American Society of Civil Engineers (ASCE)
- p. 71-80
Uppermost Subaqueous Soil Variability in Front of the Situk River Inlet, Alaska, from Portable Free Fall Penetrometer
Nearshore areas in front of river inlets feature significant spatial and temporal variations in sediment distribution, transport, and deposition processes. This makes subaqueous sediment characterization of such locations essential for engineering applications and for the fundamental understanding of regional geomorphodynamics. Site investigation was conducted in the nearshore area off the Situk River Inlet, Yakutat, Alaska. This region is characterized by highly variable sediments and energetic wave conditions. In situ tests were conducted along ten cross shore transects with 64 locations in total using a portable free fall penetrometer. The results showed the presence of a loose sediment top layer of 3.8–6.9 cm in thickness overlying a stiffer stratum with a maximum quasi-static bearing capacity ranging from 30–106 kPa at sediment depths of less than 15 cm. More variability in sediment strength was observed with decreasing water depths (approaching the shore), and sediment strength generally somewhat decreased seaward. For transects closer to the inlet, a more distinct trend of decreasing sediment strength with distance to the shore was observed. As expected, the impact of waves on the sediments appeared significant in shallow water depths. The results suggested an influence of hydrodynamics and the presence of the inlet on the topmost sediment layers, and consequently on the geotechnical characteristics.
- Open Access
- 8 February 2019
- Published by Wiley in Limnology and Oceanography: Methods
- Vol. 17 (2) , 163-176
Performance of a novel sediment sampler as an add‐on unit for portable free‐fall penetrometers: Combining in situ geotechnical testing with sediment sampling
The investigation of mobile and loose surficial sediment layers is essential for a comprehensive seabed characterization. Portable free‐fall penetrometers (PFFPs) can deliver in situ geomechanical information about surficial sediment layers, which are difficult to preserve with traditional sampling tools. However, PFFP data interpretation can be hampered by the lack of high‐quality physical sediment samples for further verification and calibration. In this study, four new sampler configurations are tested as add‐ons for PFFPs to conduct high‐quality sediment sampling and geotechnical profiling simultaneously. Laboratory results showed that the recovery ratio of the collected samples decreased with increasing impact velocities of the probe. For impact velocities ≥ 2 m s−1, a cylindrical sampler body performed better than a conical body reaching a higher recovery ratio with less disturbance on density and saturation. Sharper carvers also increased the recovery ratio and decreased the disturbance. Field results revealed that the sample retention was challenged by energetic hydrodynamics in combination with coarse sediments (significant wave height in excess of 2 m). Overall, utilization of suction proved to be the most promising retaining mechanism under various hydrodynamic and soil conditions. Geomechanical profiles obtained with the sampler add‐ons were successfully calibrated to records obtained with the traditional PFFP tip geometries. In conclusion, the study introduced a novel sediment sampler configuration suitable for simultaneous geotechnical seabed profiling and sediment sampling using PFFP and provided insights into the impacts of sampling mechanisms on sample quality.
- 8 February 2019
- Published by Wiley in Limnology and Oceanography: Methods
- Vol. 17 (2) , 163-176
Open AccessPerformance of a novel sediment sampler as an add‐on unit for portable free‐fall penetrometers: Combining in situ geotechnical testing with sediment sampling
The investigation of mobile and loose surficial sediment layers is essential for a comprehensive seabed characterization. Portable free‐fall penetrometers (PFFPs) can deliver in situ geomechanical information about surficial sediment layers, which are difficult to preserve with traditional sampling tools. However, PFFP data interpretation can be hampered by the lack of high‐quality physical sediment samples for further verification and calibration. In this study, four new sampler configurations are tested as add‐ons for PFFPs to conduct high‐quality sediment sampling and geotechnical profiling simultaneously. Laboratory results showed that the recovery ratio of the collected samples decreased with increasing impact velocities of the probe. For impact velocities ≥ 2 m s−1, a cylindrical sampler body performed better than a conical body reaching a higher recovery ratio with less disturbance on density and saturation. Sharper carvers also increased the recovery ratio and decreased the disturbance. Field results revealed that the sample retention was challenged by energetic hydrodynamics in combination with coarse sediments (significant wave height in excess of 2 m). Overall, utilization of suction proved to be the most promising retaining mechanism under various hydrodynamic and soil conditions. Geomechanical profiles obtained with the sampler add‐ons were successfully calibrated to records obtained with the traditional PFFP tip geometries. In conclusion, the study introduced a novel sediment sampler configuration suitable for simultaneous geotechnical seabed profiling and sediment sampling using PFFP and provided insights into the impacts of sampling mechanisms on sample quality.
- 1 January 2019
- Published by Elsevier in Coastal Engineering
- Vol. 143, 21-37
Investigation of spatial and short-term temporal nearshore sandy sediment strength using a portable free fall penetrometer
- 1 January 2019
- Published by Elsevier in Coastal Engineering
- Vol. 143, 21-37
Investigation of spatial and short-term temporal nearshore sandy sediment strength using a portable free fall penetrometer
- 1 November 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Waterway, Port, Coastal, and Ocean Engineering
- Vol. 144 (6)
In Situ Geotechnical Characteristics of Surficial Wetland Waterway Sediments
Geotechnical surface sediment properties and behavior contribute to the success of wetland conservation and remediation actions, but the correlation between geotechnical sediment characteristics and active morphodynamics in such areas is still poorly understood. Therefore, a field investigation of surficial sediments was conducted in wetland waterways in the Terrebonne Parish, the St. Bernard Parish, and the Rigolets in coastal Louisiana. In situ tests were conducted at 290 locations using a portable free-fall penetrometer, supported by seven sediment core samples and data available from the literature. The results allowed the authors to map changes in sediment strength and stratification and discuss them with regard to local site characteristics, such as sediment type, abundance of vegetation, and vicinity to human-made structures and engineering activities, and to the local geomorphology. Stiff sediments were observed at submerged banks and bars. Two lakes differed significantly in their sediment-strength profiles, indicating differences in sediment-deposition history. Meandering resulted in an asymmetry of the geotechnical cross-channel profile. In summary, geotechnical sediment characteristics seem to reflect the inferred local sediment dynamics.
- 1 November 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Waterway, Port, Coastal, and Ocean Engineering
- Vol. 144 (6)
In Situ Geotechnical Characteristics of Surficial Wetland Waterway Sediments
Geotechnical surface sediment properties and behavior contribute to the success of wetland conservation and remediation actions, but the correlation between geotechnical sediment characteristics and active morphodynamics in such areas is still poorly understood. Therefore, a field investigation of surficial sediments was conducted in wetland waterways in the Terrebonne Parish, the St. Bernard Parish, and the Rigolets in coastal Louisiana. In situ tests were conducted at 290 locations using a portable free-fall penetrometer, supported by seven sediment core samples and data available from the literature. The results allowed the authors to map changes in sediment strength and stratification and discuss them with regard to local site characteristics, such as sediment type, abundance of vegetation, and vicinity to human-made structures and engineering activities, and to the local geomorphology. Stiff sediments were observed at submerged banks and bars. Two lakes differed significantly in their sediment-strength profiles, indicating differences in sediment-deposition history. Meandering resulted in an asymmetry of the geotechnical cross-channel profile. In summary, geotechnical sediment characteristics seem to reflect the inferred local sediment dynamics.
- 30 March 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 379-388
Design and Preliminary Tests of Mobile Seafloor Layer Sampler Prototypes as an Add-On Unit for Portable Free-Fall Penetrometers
Portable free-fall penetrometers (PFFP) are used as an innovative approach to investigate the uppermost seabed stratification, including the mobile layer. The aim of this study is to design an add-on sampler for PFFPs to collect simultaneously sediment, with focus on the mobile sediment layer. Here, we present three prototype designs and preliminary tests, based on the lessons learned from other systems such as gravity and piston corers. The prototypes differ in shape, sampling tube dimensions, wall thickness ratios, and core catching mechanisms. In preliminary tests, the sample quality was assessed based on visuals, recovery ratio and volume change. Promising results were achieved using suction only to hold the material in the sampling tube, causing the least sample disturbance. Still, the results showed that core catcher increased the chance of recovery of sand. Based on the results, recommendations for further sampler improvements, and particularly, a new core catcher design are given.
- 30 March 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 379-388
Design and Preliminary Tests of Mobile Seafloor Layer Sampler Prototypes as an Add-On Unit for Portable Free-Fall Penetrometers
Portable free-fall penetrometers (PFFP) are used as an innovative approach to investigate the uppermost seabed stratification, including the mobile layer. The aim of this study is to design an add-on sampler for PFFPs to collect simultaneously sediment, with focus on the mobile sediment layer. Here, we present three prototype designs and preliminary tests, based on the lessons learned from other systems such as gravity and piston corers. The prototypes differ in shape, sampling tube dimensions, wall thickness ratios, and core catching mechanisms. In preliminary tests, the sample quality was assessed based on visuals, recovery ratio and volume change. Promising results were achieved using suction only to hold the material in the sampling tube, causing the least sample disturbance. Still, the results showed that core catcher increased the chance of recovery of sand. Based on the results, recommendations for further sampler improvements, and particularly, a new core catcher design are given.