Jean-Luc Hanus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jean-Luc Hanus has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
Antoine Ferreira
6 shared publicationsPatrice Bailly
Univ Tours, Univ Orleans, INSA CVL, LaMe EA7494, 88 Blvd Lahitolle, F-18000 Bourges, France
6 shared publicationsHamid Ladjal
Institut PRISME, Ecole Nationale Supérieure d’Ingénieurs de Bourges, 18000 Bourges, France
5 shared publications- Franck Delvare
Normandie Univ, UNICAEN, CNRS, LMNO, F-14000 Caen, France
4 shared publications M. Reimeringer
INERIS, Verneuil en Halatte , France
3 shared publicationsP. Bailly
PRISME – ENSI bourges – Loire Valley University 88 boulevard Lahitolle F-18020 Bourges Cedex , France
3 shared publications
Latest Publications
- Open Access
- 5 August 2026
- Published by EDP Sciences in Mechanics & Industry
- Vol. 27, 36
Characterization of shock-induced cavitation through experimental approach
Ballistic protection devices aim to intercept projectiles and mitigate their kinetic energy in order to limit bodily harm. However, even with this mitigation, a shock wave can propagate through the protection to the human body. The emission of shock waves can cause rapid expansion followed by cavitation in biological fluids, resulting in bubble nucleation and growth. Consequently, the unstable implosion of cavitation bubbles, which can be potentially devastating, remains partially misunderstood regarding its effects on human tissues. The objective of this research is to better understand the mechanical loads related to this phenomenon. The main objective is to identify the factors that influence cavitation thresholds, bubble dynamics, and their implosion in order to assess their impact on human tissues. Laboratory tests are performed using a gas launcher that shoots steel balls at intermediate velocity (100–200 m/s) onto a steel plate associated with a liquid. This experiment offers the possibility to monitor impact conditions while observing the creation and collapse of cavitation bubbles through a high-speed camera. Pressure sensors simultaneously record dynamic pressure changes in the fluid near the cavitation region. Initial trials validated the existence of post-impact cavitation, with bubbles visualized by fast imaging. Pressure analysis enabled the identification of factors that influence bubble creation, including impact velocity, initial pressure, and the pressure peak produced during implosion. The analysis also enabled the determination of bubble lifetime as well as the temporal evolution of their radius, providing essential data to improve understanding of the phenomenon.
- 5 August 2026
- Published by EDP Sciences in Mechanics & Industry
- Vol. 27, 36
Open AccessCharacterization of shock-induced cavitation through experimental approach
Ballistic protection devices aim to intercept projectiles and mitigate their kinetic energy in order to limit bodily harm. However, even with this mitigation, a shock wave can propagate through the protection to the human body. The emission of shock waves can cause rapid expansion followed by cavitation in biological fluids, resulting in bubble nucleation and growth. Consequently, the unstable implosion of cavitation bubbles, which can be potentially devastating, remains partially misunderstood regarding its effects on human tissues. The objective of this research is to better understand the mechanical loads related to this phenomenon. The main objective is to identify the factors that influence cavitation thresholds, bubble dynamics, and their implosion in order to assess their impact on human tissues. Laboratory tests are performed using a gas launcher that shoots steel balls at intermediate velocity (100–200 m/s) onto a steel plate associated with a liquid. This experiment offers the possibility to monitor impact conditions while observing the creation and collapse of cavitation bubbles through a high-speed camera. Pressure sensors simultaneously record dynamic pressure changes in the fluid near the cavitation region. Initial trials validated the existence of post-impact cavitation, with bubbles visualized by fast imaging. Pressure analysis enabled the identification of factors that influence bubble creation, including impact velocity, initial pressure, and the pressure peak produced during implosion. The analysis also enabled the determination of bubble lifetime as well as the temporal evolution of their radius, providing essential data to improve understanding of the phenomenon.
- Open Access
- 19 August 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 207
Comparative study of three cellular materials under blast and sustained shock wave
- 19 August 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 207
Open AccessComparative study of three cellular materials under blast and sustained shock wave
- 25 June 2023
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 180
Effect of loading rate on the compressive behaviour of twill woven carbon/polyamide laminate
- 25 June 2023
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 180
Effect of loading rate on the compressive behaviour of twill woven carbon/polyamide laminate
- Open Access
- 6 January 2022
- Published by Trans Tech Publications, Ltd. in Construction Technologies and Architecture
- Vol. 1, 227-233
Mechanical Compression and Crushing Properties of a Straw-Lime Material
The aim of this study was to determine the compressive mechanical properties and the energy absorption characteristics of a bio-composite material based on lime, wheat straw, and additives (protein and entraining agent). The selected samples with fiber to binder ratio of 30% were subjected to compression tests at different strain rates (1 mm/min, 10 mm/min, and 100 mm/min), in the perpendicular and parallel directions to fiber orientation. Image analysis supported with Digital Image Correlation (DIC) method is performed to follow longitudinal and lateral deformations, thus making it possible to evaluate elastic properties. The results show that the highest density and compressive strength in the parallel direction are ~349 kg/m3 and ~0.101 MPa, respectively. The perpendicular specimens at 100 mm/min of speed test showed the highest values of densification strain, stress plateau, energy efficiency, and absorbed-energy of 47.27%, 0.32 MPa, 16.98 %, and 13.84 kJ/m2, respectively. The values of Young’s modulus identified with DIC are significantly different from those determined by the slope of the linear part of the stress-strain curve. A slight influence of strain rate on mechanical properties is observed.
- 6 January 2022
- Published by Trans Tech Publications, Ltd. in Construction Technologies and Architecture
- Vol. 1, 227-233
Open AccessMechanical Compression and Crushing Properties of a Straw-Lime Material
The aim of this study was to determine the compressive mechanical properties and the energy absorption characteristics of a bio-composite material based on lime, wheat straw, and additives (protein and entraining agent). The selected samples with fiber to binder ratio of 30% were subjected to compression tests at different strain rates (1 mm/min, 10 mm/min, and 100 mm/min), in the perpendicular and parallel directions to fiber orientation. Image analysis supported with Digital Image Correlation (DIC) method is performed to follow longitudinal and lateral deformations, thus making it possible to evaluate elastic properties. The results show that the highest density and compressive strength in the parallel direction are ~349 kg/m3 and ~0.101 MPa, respectively. The perpendicular specimens at 100 mm/min of speed test showed the highest values of densification strain, stress plateau, energy efficiency, and absorbed-energy of 47.27%, 0.32 MPa, 16.98 %, and 13.84 kJ/m2, respectively. The values of Young’s modulus identified with DIC are significantly different from those determined by the slope of the linear part of the stress-strain curve. A slight influence of strain rate on mechanical properties is observed.
- 28 May 2020
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 45 (8) , 1281-1292
Mechanical Behaviour of a NTO and RDX‐Based Melt Cast Explosive
Constitutive equationsThe XF explosive family from NEXTER Munitions relies on a melt cast formulation with a TNT matrix. Melt cast formulations provide a high‐volume ratio of energetic filler material to matrix. This might affect the mechanical response of the material and its damage process. Therefore, a laboratory study has been launched to improve the knowledge of the mechanical behavior of this family of energetic materials. To mimic the conditions observed by the material inside ammunition, we chose to adapt a passive confinement method to the pyrotechnic conditions of the XF‐11585. This relies on an elastic‐perfectly plastic ring that gives us access to the shear behavior for different loadings in quasi‐static regime. This setup allowed us to investigate the physical phenomena involved under both pressure and shear. Then, based on the results obtained, we built an isotropic elastic damage model. This macroscopic modeling of damage is meant to be simple but complex enough to provide an assessment of the material degradation.
- 28 May 2020
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 45 (8) , 1281-1292
Mechanical Behaviour of a NTO and RDX‐Based Melt Cast Explosive
Constitutive equationsThe XF explosive family from NEXTER Munitions relies on a melt cast formulation with a TNT matrix. Melt cast formulations provide a high‐volume ratio of energetic filler material to matrix. This might affect the mechanical response of the material and its damage process. Therefore, a laboratory study has been launched to improve the knowledge of the mechanical behavior of this family of energetic materials. To mimic the conditions observed by the material inside ammunition, we chose to adapt a passive confinement method to the pyrotechnic conditions of the XF‐11585. This relies on an elastic‐perfectly plastic ring that gives us access to the shear behavior for different loadings in quasi‐static regime. This setup allowed us to investigate the physical phenomena involved under both pressure and shear. Then, based on the results obtained, we built an isotropic elastic damage model. This macroscopic modeling of damage is meant to be simple but complex enough to provide an assessment of the material degradation.
- 9 October 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (50) , 505204
Prediction of the spatial location of a laser-induced breakdown in argon
A modelling of the laser-induced breakdown spatial location is presented and compared to experiments where the considered variables are the incident laser energy and the initial pressure of argon in the vessel. The proposed modelling is based on the assumption that the conservation of the threshold laser energy per unit surface needs to produce a breakdown. The experiment consists in 100 consecutive laser shots for eight laser energies from 4.48 to 147.81 mJ at λ = 532 nm and four initial pressures, from 0.25 to 1 bar. A dimensionless number, E / E th , is also proposed to compare all obtained data to each other with E the incident energy and E th the threshold energy below the one no breakdown appears. The proposed modelling is in good agreement with observed values (<10% in most experiments) and is particularly interesting for laser-induced breakdown spectroscopy in gas where the location of the plasma is of great importance.
- 9 October 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (50) , 505204
Prediction of the spatial location of a laser-induced breakdown in argon
A modelling of the laser-induced breakdown spatial location is presented and compared to experiments where the considered variables are the incident laser energy and the initial pressure of argon in the vessel. The proposed modelling is based on the assumption that the conservation of the threshold laser energy per unit surface needs to produce a breakdown. The experiment consists in 100 consecutive laser shots for eight laser energies from 4.48 to 147.81 mJ at λ = 532 nm and four initial pressures, from 0.25 to 1 bar. A dimensionless number, E / E th , is also proposed to compare all obtained data to each other with E the incident energy and E th the threshold energy below the one no breakdown appears. The proposed modelling is in good agreement with observed values (<10% in most experiments) and is particularly interesting for laser-induced breakdown spectroscopy in gas where the location of the plasma is of great importance.
- 30 January 2019
- Published by River Publishers in European Journal of Computational Mechanics
- Vol. 27 (5-6) , 1-32
MFS fading regularization method for the identification of boundary conditions from partial elastic displacement field data
A method is proposed to solve an inverse problem in two-dimensional linear isotropic elasticity. The inverse problem consists of the determination of both the entire displacement field and the boundary conditions inaccessible to the measurement from the partial knowledge of the displacement field. The algorithm is based on a fading regularization method (FRM) and is numerically implemented using the method of fundamental solutions (MFS). The inverse technique is first validated with synthetic data and is then applied to the interpretation of experimental measurements obtained by digital image correlation (DIC).
- 30 January 2019
- Published by River Publishers in European Journal of Computational Mechanics
- Vol. 27 (5-6) , 1-32
MFS fading regularization method for the identification of boundary conditions from partial elastic displacement field data
A method is proposed to solve an inverse problem in two-dimensional linear isotropic elasticity. The inverse problem consists of the determination of both the entire displacement field and the boundary conditions inaccessible to the measurement from the partial knowledge of the displacement field. The algorithm is based on a fading regularization method (FRM) and is numerically implemented using the method of fundamental solutions (MFS). The inverse technique is first validated with synthetic data and is then applied to the interpretation of experimental measurements obtained by digital image correlation (DIC).
- Open Access
- 7 September 2018
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 183, 02020
Low energy shock response of a melt cast simulant material
To manufacture its insensitive munitions (MURAT MUnitions à Risque ATténué), NEXTER Munitions uses a melt cast explosives as an EIDS (Extremely Insensitive Detonating Substance). Unlike commonly used and well-documented EIDSs such as PBX, melt cast have a high volumetric matrix percentage. Moreover, in its life cycle, the ammunition can undergo severe loads, such as cannon firing, accidental shocks and terminal ballistics events. The objective of this paper is therefore to analyse, how these dynamic loads induce changes in the material (damage, cracking, de-cohesion), and then, to evaluate how these alterations influence the pyrotechnic properties of the melt cast explosive. To address the first point, we delimited the scope of the study in pressure and strain rate ranges which corresponds to the context of the ammunition. To safely explore this area, we have created an inert material that is morphologically and mechanically representative of the melt case explosive. It is used to setup and validate the experimental technic that will be applied to damage the melt cast explosive in the future. In this article the mechanical behaviour of the inert material is investigated under simple compression and passive confinement. This was done under the quasi-static and dynamic regimes thanks to a compression press and a Split Hopkinson Pressure Bars setup. Firstly, the results obtained show the emergence of a damage which increases with the loss of cohesion of the material during the test. This seems to be related to the extension strain. Then, for all tests, a strain rate dependent mechanical response is observed. Finally, the end of the test shows the material behaviour without cohesion. Then, a rate dependent ultimate shear criterion is deduced. To complete the interpretation these results, a model is proposed. It intends to be simple as it tries to describe the whole degradation of the material with a unique scalar parameter.
- 7 September 2018
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 183, 02020
Open AccessLow energy shock response of a melt cast simulant material
To manufacture its insensitive munitions (MURAT MUnitions à Risque ATténué), NEXTER Munitions uses a melt cast explosives as an EIDS (Extremely Insensitive Detonating Substance). Unlike commonly used and well-documented EIDSs such as PBX, melt cast have a high volumetric matrix percentage. Moreover, in its life cycle, the ammunition can undergo severe loads, such as cannon firing, accidental shocks and terminal ballistics events. The objective of this paper is therefore to analyse, how these dynamic loads induce changes in the material (damage, cracking, de-cohesion), and then, to evaluate how these alterations influence the pyrotechnic properties of the melt cast explosive. To address the first point, we delimited the scope of the study in pressure and strain rate ranges which corresponds to the context of the ammunition. To safely explore this area, we have created an inert material that is morphologically and mechanically representative of the melt case explosive. It is used to setup and validate the experimental technic that will be applied to damage the melt cast explosive in the future. In this article the mechanical behaviour of the inert material is investigated under simple compression and passive confinement. This was done under the quasi-static and dynamic regimes thanks to a compression press and a Split Hopkinson Pressure Bars setup. Firstly, the results obtained show the emergence of a damage which increases with the loss of cohesion of the material during the test. This seems to be related to the extension strain. Then, for all tests, a strain rate dependent mechanical response is observed. Finally, the end of the test shows the material behaviour without cohesion. Then, a rate dependent ultimate shear criterion is deduced. To complete the interpretation these results, a model is proposed. It intends to be simple as it tries to describe the whole degradation of the material with a unique scalar parameter.
- 20 November 2017
- Published by Springer Nature in Shock Waves
- Vol. 28 (4) , 641-652
Simulating the blast wave from detonation of a charge using a balloon of compressed air
- 20 November 2017
- Published by Springer Nature in Shock Waves
- Vol. 28 (4) , 641-652
Simulating the blast wave from detonation of a charge using a balloon of compressed air