Shu-Yu Chou
Shu-Yu Chou has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Qibing Pei
Department of Materials Science and Engineering, Henry Samueli School of Engineering and Applied Science, University of California, Los Angeles, Los Angeles, CA 90095, USA
2 shared publications Fangchao Zhao
Department of Materials Science and Engineering, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles , Los Angeles, California 90095, United States
1 shared publicationKwing Tong
Department of Materials Science and Engineering, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles , Los Angeles, California 90095, United States
1 shared publicationRujun Ma
Department of Materials Science and Engineering, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles , Los Angeles, California 90095, United States
1 shared publication- Rujun Ma
School of Materials Science and Engineering Nankai University Tianjin China
1 shared publication Yu Xie
Soft Materials Research Laboratory
1 shared publication
Latest Publications
- 2 January 2019
- Published by Royal Society of Chemistry (RSC) in Chemical Society Reviews
- Vol. 48 (6) , 1741-1786
Morphological/nanostructural control toward intrinsically stretchable organic electronics
The development of intrinsically stretchable electronics poses great challenges in synthesizing elastomeric conductors, semiconductors and dielectric materials.
- 2 January 2019
- Published by Royal Society of Chemistry (RSC) in Chemical Society Reviews
- Vol. 48 (6) , 1741-1786
Morphological/nanostructural control toward intrinsically stretchable organic electronics
The development of intrinsically stretchable electronics poses great challenges in synthesizing elastomeric conductors, semiconductors and dielectric materials.
- 7 November 2017
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 11 (11) , 11368-11375
Transparent Perovskite Light-Emitting Touch-Responsive Device
A light-emitting touch-responsive device (LETD) for instantaneous visualization of pressure mapping is reported. The LETD integrates an organometal halide perovskite polymer composite emissive layer and a flexible silver nanowire polyurethane composite transparent electrode. The composite emissive layer contains methylammonium lead bromide nanocrystals uniformly dispersed in a poly(ethylene oxide) (PEO) matrix and emits an intense green luminescence that peaks at 529 nm. The PEO matrix promotes the formation of small perovskite grains (∼20 nm) and a pinhole-free composite film with surface roughness of only 2.96 nm. The composite transparent electrode is separated from the emissive layer with a 100 μm thick spacer. When a local pressure is applied, a Schottky contact is formed instantaneously between the metal and the emissive layer, and electroluminescence is produced at voltages as low as 2.5 V and reaches 1030 cd/m2 at 6 V. The transparent LETD has approximately 68% transparency. It can be bent to a 6 mm radius when polyethylene terephthalate is used as the substrate. The perovskite LETD has fast response and can be pixelated to offer potential applications in robotics, motion detection, fingerprint devices, and interactive wallpapers.
- 7 November 2017
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 11 (11) , 11368-11375
Transparent Perovskite Light-Emitting Touch-Responsive Device
A light-emitting touch-responsive device (LETD) for instantaneous visualization of pressure mapping is reported. The LETD integrates an organometal halide perovskite polymer composite emissive layer and a flexible silver nanowire polyurethane composite transparent electrode. The composite emissive layer contains methylammonium lead bromide nanocrystals uniformly dispersed in a poly(ethylene oxide) (PEO) matrix and emits an intense green luminescence that peaks at 529 nm. The PEO matrix promotes the formation of small perovskite grains (∼20 nm) and a pinhole-free composite film with surface roughness of only 2.96 nm. The composite transparent electrode is separated from the emissive layer with a 100 μm thick spacer. When a local pressure is applied, a Schottky contact is formed instantaneously between the metal and the emissive layer, and electroluminescence is produced at voltages as low as 2.5 V and reaches 1030 cd/m2 at 6 V. The transparent LETD has approximately 68% transparency. It can be bent to a 6 mm radius when polyethylene terephthalate is used as the substrate. The perovskite LETD has fast response and can be pixelated to offer potential applications in robotics, motion detection, fingerprint devices, and interactive wallpapers.