Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lucas Vizzotto Bellinaso has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Solid-State Circuit Breakers for DC-Powered Buildings: An Overview of Standards, Directives, and Technologies

    by Henrique Bizzi Morari, Lucas Vizzotto Bellinaso, Edivan Laercio Carvalho, Satish Naik Banavath, Giovanni De Carne, Dmitri Vinnikov

    This paper presents a review of low-voltage direct current (LVDC) solid-state circuit breakers (SSCBs) for building power systems, focusing on relevant standards, safety directives, and design requirements for DC protection. A structured classification scheme is proposed for LVDC SSCBs based on key design criteria including the number of poles, bidirectional current capability, isolation method, semiconductor technology, and circuit topology. This paper also proposes a categorization of SSCB protective functions into elementary safety functions (short-circuit interruption, overcurrent and overload protection, and selective coordination) and additional advanced functions (arc-fault detection, insulation monitoring, and earth-fault protection), distinguishing fundamental requirements from enhanced safety features. Furthermore, a risk assessment framework grounded in ISO 12100 principles is introduced and tailored to LVDC installations employing SSCBs. This framework systematically identifies potential hazards and SSCB failure modes, guiding risk mitigation measures and the development of test procedures to ensure compliance with safety standards. Collectively, these contributions provide clear guidelines to support the safe integration, standardization, and future development of SSCBs in emerging DC power distribution networks.


  • Open Access

    Direct Adaptive Control of Photovoltaic Boost Converters With Ultra-Low Input Capacitance

    by Andrei C. Lima, Charles Schardong, Lucas V. Bellinaso, Rodrigo V. Tambara, Leandro Michels

    Boost converters are widely used in the voltage step-up stage of photovoltaic (PV) inverters due to their simple construction. These converters must operate in both Maximum Power Point Tracking (MPPT) and Limited Power Tracking (LPT) modes, which requires effective regulation of both PV voltage and inductor current using a dual-loop control structure. Reducing the input capacitance to eliminate electrolytic capacitors and increase lifetime, however, introduces significant parametric variations, making the control design challenging and limiting the dynamic performance of the voltage controller. This work proposes a dual-loop adaptive control strategy, comprising an outer voltage loop with Model Reference Adaptive Control (MRAC) and an inner current loop with a fixed-gain PI controller. The proposed method resolves issues observed in previous works in both steady-state and transient operation, enabling fast PV voltage tracking with an ultra-low 2 $\mathrm{\mu }$F input capacitor. Experimental results demonstrate stable operation in both CCM and DCM modes, with a settling time of 7 ms at a switching frequency of 40 kHz, improved dynamic response, and applicability in PV systems under rapidly changing irradiance conditions.


  • Open Access

    Modeling and Control of a Full-Bridge DC-DC Converter for Arc Welding Applications

    by Christian G. Barbosa, Vitor De S. Guedes, Rafael C. Beltrame, Lucas V. Bellinaso, Fábio E. Bisogno, Ezequiel A. Mallmann, Luciano A. Fricke

    This study presents the modeling and control of a full-bridge DC-DC converter applied to Gas Metal Arc Welding (GMAW) in short-circuit transfer mode. GMAW is widely used in industrial manufacturing due to its versatility. However, achieving stable operation in short-circuit transfer requires precise regulation of the welding current and arc voltage. To address this challenge, a simplified yet representative model of the converter and load dynamics is developed. Based on this model, a dual-loop digital control strategy is implemented to ensure fast transient response, reference tracking, and improved stability of the welding process. The effectiveness of the proposed approach is experimentally validated on an industrial-grade prototype, demonstrating agreement between theoretical predictions and measured waveforms.

  • Improving Control Systems Education in Brazilian Engineering Programs through an Iterative Project-Based Learning Approach

    by Aline R. Antunes, Giulia R. Herdies, Júlio C. Ceolin, Gustavo S. Azzolin, Luciane F. Jacobi, Antônio C. K. Filho, Gabriel Q. dos Santos, Lucas V. Bellinaso


  • Open Access

    Validation of controllers for photovoltaic inverters using automated tests and hardware-in-the-loop

    by João V. L. Rosa, Luiz F. R. Menegazzo, Lucas V. Belinaso, Fernanda de M. Carnielutti, Humberto Pinheiro

    The ABNT NBR-16149 and NBR-16150 standards and INMETRO Ordinance No. 140 establish requirements for connecting PV inverters to the Brazilian electrical grid. To meet these requirements, the firmware of these devices needs to be properly designed and validated. Additionally, it is important to perform tests to verify whether the inverter and its control systems comply with the standards. In this context, this paper presents a methodology for the validation of controllers for PV inverters using Hardware-in-the-loop (HIL). To validate the proposed methodology, a two-level three-phase PV inverter with Finite Control Set Model Predictive Control (FCS-MPC) for current control and additional control and grid connection functionalities was evaluated. The compliance of the controller with relevant standards was assessed through automated HIL testing. This approach allows control designers to identify potential issues in advance, refine algorithms, and enhance controller performance before the complete hardware certification process of the inverter.


  • Open Access

    Toward Fully-Automated Hardware-in-the-Loop Grid Code Compliance Certification of Inverter-Based Distributed Energy Resources

    by Luiz Fernando Rissotto Menegazzo, Anderson Luis Do Nascimento Severo, Ricardo Jochann Franceschi Bortolini, Lucas Bisêlo Piton, Henrique Magnago, Fernanda de Morais Carnielutti, Lucas Vizzotto Bellinaso, Leandro Michels, Humberto Pinheiro

    Inverter-based Distributed Energy Resources (DERs) third-party compliance testing has been widely required by most grid codes to guarantee interoperability with the electrical power system. However, most grid code certification procedures only accept the evaluation of the whole product under full-power environments. For high-power equipment, this procedure is costly, time-intensive, and complex to be performed. Due to this, many efforts have been made to make possible using Controller Hardware-in-the-Loop (CHIL) testing for validation of the inverter firmware from early product development through final certification, facilitating the identification of early issues and reducing debugging time and costs. On the other hand, since most CHIL tests are performed in environments distinct from full power laboratory testing, both approaches often follow different procedures and do not take into account the same metrics, which can result in low fidelity between CHIL and power laboratory results. In order to make possible to use CHIL for compliance testing, model validation has to be performed, guaranteeing that model fidelity is satisfactory. In this context, this paper presents a comprehensive methodology to validate CHIL models and to clearly identify, measure, and reduce differences between the results obtained with CHIL and with power laboratory testing environments. The methodology is based on standardized quantitative test procedures applied to both CHIL and power laboratory testing. The proposed methodology is extensively validated through experimental results carried out on a commercial single- phase photovoltaic inverter. Results demonstrate the validity of CHIL testing methodology and propose an alternative method for grid code compliance testing and certification.


  • Open Access

    Unified Platform for Automated Tests of Inverter-Based Resources with Hardware-in-the-loop

    by Luiz F. R. Menegazzo, Anderson L. N. Severo, Lucas Bisêlo Piton, Catherine Marquioro De Freitas, Ricardo Jochann Franceschi Bortolini, Lucas Vizzotto Bellinaso, Leandro Michels, Fernanda de Morais Carnielutti

    Testing of inverter-based resources (IBRs) faces challenges in establishing standardized procedures across all product development stages. Most of the testing approaches use Hardware-in-the-Loop (HIL) during the early stages independently from the final product testing, which can lead to discrepant results. To solve these issues, this paper proposes a unified platform for automatically testing IBRs. It can be used during all product development stages, from pure simulation to Controller Hardware-in-the-Loop (CHIL) and finally on the complete commercial product, ensuring uniform test procedures with different test setups. A case study describing compliance tests of grid-connection codes of photovoltaic (PV) inverters are presented to demonstrate the proposed approach. Experimental tests were performed in accordance to Brazilian grid-connection codes in an ISO/IEC 17025 accredited laboratory. The results obtained with the proposed platform in CHIL and full-hardware showed high similarity with the ones obtained with the accredited laboratory, validating the proposed approach. In addition, the platform can be used to perform tests not specified in standards and to verify the performance of IBRs in operating conditions that are often difficult to be tested in laboratory. Ensuring consistent test procedures, the platform facilitates comparable results along all the testing stages, reducing the product development cycle.


  • Open Access

    Methodology to Define an Overall Efficiency of Photovoltaic Inverters Considering Static and Dynamic Tests

    by Henrique Horst Figueira, Fernando S. Scherer, Ricardo J. F. Bortolini, Lucas Vizzotto Bellinaso, Leandro Michels

    Efficiency indices for inverters have been developed with the increasing adoption of photovoltaic (PV) systems. The European and Californian efficiencies are widely recognized, focusing on static inverter operation. Standards such as EN50530 and IEC 62891 introduced dynamic efficiency tests considering irradiance variations, but without a methodology to weigh the efficiencies within a single index. To address this gap, our study proposes a methodology to define an overall efficiency considering both static and dynamic inverter operation. Irradiance data with sub-minute sampling is classified into irradiance and irradiance derivative ranges. Then, weights for static and dynamic efficiency tests are obtained, and less significant ones are discarded. The results were applied to three PV inverters tested in the laboratory. By eliminating the less significant tests, the number of dynamic tests was reduced from 30 to 10. In two of the inverters, the inclusion of dynamic tests resulted in a 2\% reduction in overall efficiency compared to the static. An overall efficiency index is relevant for better comparing different PV inverters, especially when considering dynamic behaviors. This index may be significant for the PV market, governmental energy efficiency programs, and inverter manufacturers, providing guidelines to enhance the efficiency of their products.


  • Open Access

    PRÉ-CERTIFICAÇÃO DO FIRMWARE DE INVERSORES FOTOVOLTAICOS DE ACORDO COM A NORMA BRASILEIRA NBR 16150 ATRAVÉS DE HARDWARE-IN-THE-LOOP

    by Luiz Fernando Rissotto Menegazzo, Vinícius da Silva Baumhardt, Henrique de Souza Magnago, Lucas Vizzotto Bellinaso, Anderson Luis Do Nascimento Severo, Fernanda de Morais Carnielutti

    Resumo Com o advento da tecnologia hardware-in-the-loop (HIL), tornou-se possível adquirir resultados de alta confiabilidade provenientes de emulações em tempo real. Assim, este artigo descreve o projeto desenvolvido no Instituto de Redes Inteligentes da UFSM, que permite o desenvolvimento e teste de inversores fotovoltaicos através da uso de uma plataforma HIL, na qual o conversor estático de potência é emulado, enquanto o controle é realizado externamente pelo próprio processador do respectivo inversor fotovoltaico. Para apoio ao projeto, foi implementada uma bancada experimental para testar o firmware do processador de acordo com as normas brasileiras de conexão com a rede elétrica de distribuição. Este trabalho descreve a bancada implementada, bem como os testes automáticos da norma brasileira. Resultados experimentais com a placa de controle de um inversor comercial são apresentados para demonstrar os procedimentos de ensaio desenvolvidos. Esse projeto pode servir para acelerar o desenvolvimento de inversores fotovoltaicos, oferecendo ao fabricante resultados confiáveis muito semelhantes ao teste final para certificação com equipamentos reais.


  • Open Access

    Extended ZVS-On/ZCS-Off Range for CF-DAB Converter Under DCM Operation for Residential Energy Storage Systems

    by Edivan Laercio Carvalho, Rafael Cardoso, Carla Aparecida Felipe, Carlos Marcelo De Oliveira Stein, Lucas Vizzotto Bellinaso, Leandro Michels, Dmitri Vinnikov

    Current-Fed Dual-Active Bridge (CF-DAB) converters are interesting in bidirectional applications when a wide conversion voltage ratio is required, such as residential extra-low voltage energy storage systems, where conventional DAB converters have several limitations. Even though several developments have been made in the last few years to improve the CF-DAB technology for such applications, ensuring a flat efficiency curve is still challenging since it is not easy to ensure high efficiency at very low power. Current solutions include phase-shift modulations (PSM), dual phase-shift (DPSM), and hybrid approaches. This paper proposes an asymmetrical pulse width modulation (a-PWM) strategy to operate the CF-DAB in discontinuous conduction mode (DCM), improving the converter efficiency curve at low power. The DCM operation ensures soft-switching conditions over a wide operation range, providing a simple and effective solution. It is relevant to CF-DAB converter development because conventional modulations have limitations concerning the soft-switching range and usually result in overvoltage problems. A 500 W prototype was built and tested to evaluate this proposal. The experimental results show the a-PWM ensures soft-switching from 2% to 100% of the converter rated power, and the efficiency curve is almost flat due to the improved efficiency at low power level.