NPNirmana Perera

Nirmana Perera

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Nirmana Perera has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • In-Chip Microfluidic Cooling Integrated on GaN Power IC Reaching High Power Density of 78 kW/l

    by Remco van Erp, Nirmana Perera, Luca Nela, Ibrahim Osama Elhagali, Hongkeng Zhu, Elison Matioli

    The lateral structure of gallium nitride (GaN) semiconductors enables monolithic integration of logic and power devices, which offers promise to miniaturize bulky converters into a compact package. However, the concentrated heat that arises from this dense integration can locally exceed 1 kW/cm 2 , which surpasses the limit of current thermal management technologies. In this article, we demonstrate the potential of integrating in-chip microfluidic cooling directly on GaN power integrated circuits (ICs), together with additively manufactured packaging, to provide efficient thermal management, and achieve ultrahigh-power densities. A prototype power module and a 0.44 kW 48 V–24 V dc--dc converter were realized in a compact 32nd brick form factor to demonstrate its potential. Our results show a 14-fold reduction in thermal resistance and a four-fold increase in the total output power compared to heat-sink and fan cooling. An outstanding 78 kW/l was achieved, together with an increase in power conversion efficiency, surpassing 95%. By removing thermal limitations from power IC design, and enabling highly integrated topologies combined in a single liquid-cooled chip, this work paves the way for more efficient and highly compact power conversion in the future to support the electrification of our society.


  • Hard-Switching Losses in Power FETs: The Role of Output Capacitance

    by Nirmana Perera, Armin Jafari, Reza Soleimanzadeh, Nicolas Bollier, Sunil Gamini Abeyratne, Elison Matioli

    For certain field-effect transistors (FETs) in soft-switching operation, the large-signal behavior of their output capacitance ( ${C}_\text{o}$ ) has shown to deviate considerably from the datasheet values. This can have a significant effect on hard-switching losses if the value of output charge is also different for a given voltage. In addition, standard hard-switching tests are incapable of fully setting apart the contributions from ${C}_\text{o}$ , whereas existing methods tailored to characterize ${C}_\text{o}$ losses in soft-switching operations subject ${C}_\text{o}$ to a fundamentally different charge–discharge process, and hence, might not predict the correct behavior for hard switching. To address this, first, we analyze and establish the particular charge–discharge conditions that ${C}_\text{o}$ undergoes in hard-switching circuits by considering a half bridge at no-load conditions. We show that the channel of the switching device incurs a fixed energy loss during the turn- on process, which is separated into co-energy and stored energy components of the top (complementary) and bottom (switching) devices, respectively. Exploiting this, a new measurement technique is developed to obtain output-charge versus voltage curves of devices subjected to actual hard switching. The experimental results for commercial Si, SiC, and GaN devices indicate that the effective charge-capacity of ${C}_\text{o}$ for hard switching can considerably vary from the values based on datasheets or Sawyer–Tower circuit; this could greatly undermine efficiency and thermal optimizations in the design phase of power converters.


  • Impact of Embedded Liquid Cooling on the Electrical Characteristics of GaN-on-Si Power Transistors

    by Luca Nela, Remco Van Erp, Nirmana Perera, Armin Jafari, Catherine Erine, Elison Matioli

    Wide-Band-Gap semiconductors have enabled considerable miniaturization of power devices, which requires, however, new thermal management solutions to handle the resulting high heat fluxes. Recently, embedded liquid cooling in GaN-on-Si devices was demonstrated as a promising solution by flowing a coolant through microchannels etched in the silicon substrate. However, its impact on power devices’ electrical characteristics, especially at high voltage, is yet to be investigated, which is crucial to assess the viability of the technology. Besides, previous demonstrations were limited to relatively low-power devices, while embedded liquid cooling for high-current and high-voltage (650 V) commercial GaN transistors would show the full potential of the technology. Here, we integrate embedded liquid cooling on 650 V, 50 $\text{m}\Omega $ GaN-on-Si commercial power devices. We demonstrate no negative impact on the device dc or switching performance due to the embedded liquid cooling, which proves the robustness and validity of the technology. Besides, liquid-cooled devices show more than $4\times $ higher current capability and much-improved ${R}_{\mathrm{ON}} \times \,\,{E}_{{\text {oss}}}$ figure-of-merit in a large output current range compared to forced-convection air-cooling, highlighting their potential for high-current applications. Finally, deionized water and a dielectric fluid (3M Novec 7200) are compared as coolants, revealing a trade-off between thermal performance and reliability during high-voltage operation.


  • Performance of GaN Power Devices for Cryogenic Applications Down to 4.2 K

    by Luca Nela, Nirmana Perera, Catherine Erine, Elison Matioli

    Gallium nitride (GaN) power devices are employed in an increasing number of applications thanks to their excellent performance. Nevertheless, their potential for cryogenic applications, such as space, aviation, and superconducting systems, has not yet been fully explored. In particular, little is known on the device performance below liquid nitrogen temperature (77 K) and the behavior of popular GaN architectures such as Gate Injection Transistor (GIT) and Cascode below room temperature has not yet been reported. Most importantly, it is still unclear how the different device loss contributions, i.e. conduction, soft- and hard-switching losses, change at cryogenic temperatures. In this work, we investigate and compare the performance of four GaN commercial power devices in a wide temperature range between 400 K and 4.2 K. All of the tested devices can successfully operate at cryogenic temperature with an overall performance improvement. However, different GaN HEMT technologies lead to significant variations in device gate control and loss mechanisms, which are discussed based on the device structure. The presented results prove the promising potential of the GaN technology for low-temperature applications and provide precious insights to properly design power systems operating under cryogenic temperatures and maximize their efficiency.


  • Erratum to “Comparison of Wide-Band-Gap Technologies for Soft-Switching Losses at High Frequencies” [Dec 20 12595-12600]

    by Armin Jafari, Mohammad Samizadeh Nikoo, Nirmana Perera, Halil Kerim Yildirim, Furkan Karakaya, Reza Soleimanzadeh, Elison Matioli

    Presents corrections to the above named paper.

  • Analysis of Large-Signal Output Capacitance of Transistors Using Sawyer–Tower Circuit

    by Nirmana Perera, Georgios Kampitsis, Remco van Erp, Jessy Ancay, Armin Jafari, Mohammad Samizadeh Nikoo, Elison Matioli

    A detailed analysis of the Sawyer-Tower method used in the measurement of large-signal output capacitance ( C o ) of power transistors is presented, followed by important design recommendations to obtain accurate results. Key factors affecting the proper implementation of the technique, such as power amplifier characteristics, load slew rate, reference capacitor ( C ref ), and reverse conduction of the device, are addressed, with accompanying simulation and experimental results for Si, SiC, and GaN devices. A thorough investigation of the selection of C ref is presented, with a new equation to correctly determine its value for a given voltage swing and output capacitance range of the device under test (DUT). We report that the Sawyer-Tower circuit imposes the DUT to enter steady-state reverse conduction under certain conditions, thus leading to charge-voltage (QV) hysteresis patterns unrelated to C o . Our analysis reveals that the origin of this phenomenon is related to DUT's leakage current and it could be minimized by the proper selection of excitation frequency. This article intends to provide an effective guide on designing and using the Sawyer-Tower circuit, and to induce further scientific insight on characterizing C o .


  • $C_{\text{oss}}$ Loss Tangent of Field-Effect Transistors: Generalizing High-Frequency Soft-Switching Losses

    by Nirmana Perera, Mohammad Samizadeh Nikoo, Armin Jafari, Luca Nela, Elison Matioli

    The dissipated energy (E $diss$ ) related to the resonant charging/discharging of a transistor output capacitance, becomes a dominant loss factor for power converters operating in the MHz range. A recent work has introduced a small-signal measurement method to quantify E $diss$ with a frequency-dependent small-signal resistance, R $_s$ , and an effective small-signal output capacitance, C ${^eff} {_oss}$ . This work provides further insights on the effect of R $s$ and C $_oss$ upon the device losses in a broader sense. In particular, the C $_oss$ loss tangent, tan (δ), is introduced as a normalized E $diss$ to combine the roles of R $s$ and C $_oss$ together with the operating frequency into a single loss parameter. By evaluating commercial device families, it is demonstrated that tan (δ) is constant for a given family, independent of the device on-resistance R $_DS(on)$ . It is shown that a minimum E $diss$ is achieved by having the lowest tan (δ) for a given stored energy (E $_oss$ ) in C $_oss$ . With accompanying guidelines, this work identifies tan (δ) as a powerful figure of merit to classify field-effect transistors for soft-switching applications, regardless of on-resistance variation of devices within a family. The proposed concept provides a comprehensive method to characterize and benchmark power transistors for high-frequency applications.


  • Top Cited Papers

    Comparison of Wide-Band-Gap Technologies for Soft-Switching Losses at High Frequencies

    by Armin Jafari, Mohammad Samizadeh Nikoo, Nirmana Perera, Halil Kerim Yildirim, Furkan Karakaya, Reza Soleimanzadeh, Elison Matioli


  • Open Access

    Publisher Correction: Nanoplasma-enabled picosecond switches for ultrafast electronics

    by Mohammad Samizadeh Nikoo, Armin Jafari, Nirmana Perera, Minghua Zhu, Giovanni Santoruvo, Elison Matioli

    An amendment to this paper has been published and can be accessed via a link at the top of the paper.


  • Efficient High Step-Up Operation in Boost Converters Based on Impulse Rectification

    by Mohammad Samizadeh Nikoo, Armin Jafari, Nirmana Perera, Elison Matioli

    Conventional boost converters, while having a high level of simplicity and robustness, are known to have poor efficiency at high step-up regime. More complicated topologies have been extensively explored to increase the step-up ratio while keeping a high-efficiency, however, an efficient regulated dc-dc power conversion at high step-up regime still remains a challenge. In this work we demonstrate fully soft-switched operation of boost converters based on impulse rectification, which results in an efficient power conversion at very high step-up regime. Contrary to the conventional analysis of boost converters which seeks to minimize conduction and switching losses, our approach considers reactive power as the key parameter limiting efficiency. A theoretical basis for this operation mode enabled an appropriate design resulting in power conversion efficiencies above 90% for voltage gain values of 5, 10, 25, and 50, with a peak efficiency of 97%. The guidelines to design boost converters based on the proposed approach are discussed. The simplicity and high performance of this approach opens new avenues in designing regulated dc-dc converters with a high step-up.