AJArmin Jafari

Armin Jafari

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Armin Jafari has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Hard-Switching Losses in Power FETs: The Role of Output Capacitance

    by Nirmana Perera, Armin Jafari, Reza Soleimanzadeh, Nicolas Bollier, Sunil Gamini Abeyratne, Elison Matioli

    For certain field-effect transistors (FETs) in soft-switching operation, the large-signal behavior of their output capacitance ( ${C}_\text{o}$ ) has shown to deviate considerably from the datasheet values. This can have a significant effect on hard-switching losses if the value of output charge is also different for a given voltage. In addition, standard hard-switching tests are incapable of fully setting apart the contributions from ${C}_\text{o}$ , whereas existing methods tailored to characterize ${C}_\text{o}$ losses in soft-switching operations subject ${C}_\text{o}$ to a fundamentally different charge–discharge process, and hence, might not predict the correct behavior for hard switching. To address this, first, we analyze and establish the particular charge–discharge conditions that ${C}_\text{o}$ undergoes in hard-switching circuits by considering a half bridge at no-load conditions. We show that the channel of the switching device incurs a fixed energy loss during the turn- on process, which is separated into co-energy and stored energy components of the top (complementary) and bottom (switching) devices, respectively. Exploiting this, a new measurement technique is developed to obtain output-charge versus voltage curves of devices subjected to actual hard switching. The experimental results for commercial Si, SiC, and GaN devices indicate that the effective charge-capacity of ${C}_\text{o}$ for hard switching can considerably vary from the values based on datasheets or Sawyer–Tower circuit; this could greatly undermine efficiency and thermal optimizations in the design phase of power converters.


  • Impact of Embedded Liquid Cooling on the Electrical Characteristics of GaN-on-Si Power Transistors

    by Luca Nela, Remco Van Erp, Nirmana Perera, Armin Jafari, Catherine Erine, Elison Matioli

    Wide-Band-Gap semiconductors have enabled considerable miniaturization of power devices, which requires, however, new thermal management solutions to handle the resulting high heat fluxes. Recently, embedded liquid cooling in GaN-on-Si devices was demonstrated as a promising solution by flowing a coolant through microchannels etched in the silicon substrate. However, its impact on power devices’ electrical characteristics, especially at high voltage, is yet to be investigated, which is crucial to assess the viability of the technology. Besides, previous demonstrations were limited to relatively low-power devices, while embedded liquid cooling for high-current and high-voltage (650 V) commercial GaN transistors would show the full potential of the technology. Here, we integrate embedded liquid cooling on 650 V, 50 $\text{m}\Omega $ GaN-on-Si commercial power devices. We demonstrate no negative impact on the device dc or switching performance due to the embedded liquid cooling, which proves the robustness and validity of the technology. Besides, liquid-cooled devices show more than $4\times $ higher current capability and much-improved ${R}_{\mathrm{ON}} \times \,\,{E}_{{\text {oss}}}$ figure-of-merit in a large output current range compared to forced-convection air-cooling, highlighting their potential for high-current applications. Finally, deionized water and a dielectric fluid (3M Novec 7200) are compared as coolants, revealing a trade-off between thermal performance and reliability during high-voltage operation.


  • Kilowatt-Range Picosecond Switching Based on Microplasma Devices

    by Mohammad Samizadeh Nikoo, Armin Jafari, Remco Van Erp, Elison Matioli

    Plasma formation in micro- and nano-scales enables an ultrahigh-dv/dt picosecond switching in an integrated circuit form factor. Such on-chip plasma devices could provide a transformative approach to achieving high-power levels at very high frequencies, far surpassing the best performance of conventional III-V electronics. In this work, we demonstrate the application of scaled-up nano- and microplasma switches as discrete devices in high-performance picosecond pulsed-power sources. A prototype circuit, utilizing the fabricated plasma devices operating as the switch, shows a high voltage-rising-rate beyond 10 kV ns -1 at 15 kW peak power. The pulsed-power source exhibits a sub-100 ps rise-time (without de-embedding). The device has the capability of reaching exceptionally high current densities up to 325 A mm -1 . The switches are compatible with planar semiconductor fabrication, enabling their integration with other electronic devices and microwave components, which opens pathways towards the future ultrahigh power density picosecond pulsed-power sources.


  • Resonances on GaN-on-Si Epitaxies: A Source of Output Capacitance Losses in Power HEMTs

    by Mohammad Samizadeh Nikoo, Riyaz Abdul Khadar, Armin Jafari, Minghua Zhu, Elison Matioli

    GaN-on-Si high-electron-mobility transistors (HEMTs) exhibit excellent properties for efficient power conversion. Nevertheless, a considerable energy loss associated with the charging and discharging of the output capacitance (COSS) in these transistors severely limits their application at high switching frequencies. In this work we report the observation of unexpected resonances in GaN-on-Si HEMTs. These high-frequency resonances lead to considerable energy losses in fast charging and discharging of the COSS during switching transients. We propose a simple wafer-level measurement technique to evaluate such losses at the epitaxy level, prior to the transistor fabrication. Experimental results from this technique revealed that the Silicon substrate is the main origin of these losses. Such wafer-level evaluation of COSS losses opens opportunities to characterize and optimize epitaxies for future power devices, especially those operating at high switching frequencies.


  • Optimized Kilowatt-Range Boost Converter Based on Impulse Rectification With 52 kW/l and 98.6% Efficiency

    by Armin Jafari, Mohammad Samizadeh Nikoo, Remco van Erp, Elison Matioli

    Maximizing the efficiency and power density of dc-dc converters demands parallel optimizations in design and control, especially for variable-frequency converters operating over wide frequency ranges. This work presents the full-scale optimization of a kilowatt-range MHz-class boost converter based on impulse rectification. To maximize the heat extraction from the converter and increase its power density, the entire power stage is implemented on a single-layer insulated-metal substrate (IMS). For high efficiencies over wide frequency ranges, high-performance Gallium Nitride (GaN) transistors are employed and various high-frequency materials (MnZn, NiZn, air) with different geometries are compared to realize a wide-bandwidth inductor. Silicon Carbide (SiC) Schottky diodes with zero reverse recovery are utilized for efficient high-frequency rectification, and the impact of the device current rating on its generated reactive power and the overall system efficiency is investigated at different power levels up to 1 kW. A proposed optimum duty cycle control maximizes the conversion efficiency at different gains and powers and prevents fatal device hard switching at high frequencies. The optimized converter enables a peak efficiency of 98.6% along with an ultra-high power density of 52 kW/l (850 W/inch 3). A loss breakdown summarizes major efficiency bottlenecks to be overcome by future advances in power electronics.


  • Erratum to “Comparison of Wide-Band-Gap Technologies for Soft-Switching Losses at High Frequencies” [Dec 20 12595-12600]

    by Armin Jafari, Mohammad Samizadeh Nikoo, Nirmana Perera, Halil Kerim Yildirim, Furkan Karakaya, Reza Soleimanzadeh, Elison Matioli

    Presents corrections to the above named paper.

  • High-Accuracy Calibration-Free Calorimeter for the Measurement of Low Power Losses

    by Armin Jafari, Michael Heijnemans, Reza Soleimanzadeh, Remco van Erp, Mohammad Samizadeh Nikoo, Enea Figini, Furkan Karakaya, Elison Matioli

    Wide-band-gap technologies enable ultra-high efficiencies in high-frequency power conversion. However, inadequate accuracies in electrical measurements could lead to spurious efficiency measurements, even above 100%. Furthermore, bandwidth limitations, particularly for current probing, delay mismatches between current and voltage probes, loading effects and electromagnetic interferences make electrical techniques inappropriate for measuring extremely-low losses in switches with high dv/dt and di/dt values and magnetic components with high-frequency excitations. Calorimetric methods overcome this issue by a direct loss measurement through the generated heat. Nevertheless, limited ranges and accuracies of existing systems hinder their application in sensitive measurements. Moreover, time-consuming calibrations with extensive data processing impede rapid design assessments. In this work, we propose a closed-type double-chamber calorimeter based on a real-time calibration between two identical chambers, to eliminate extra compensation for ambient variations or changes within the system itself. By streaming the same coolant in both chambers, our system removes the need for flow measurements, enabling extremely low flow rates which improves sensitivity and reduces complexity and system cost. The system provides adjustable cooling and can measure losses down to 500 mW, enabling the evaluation of high-performance power converters and their components with no dependencies on the geometries of the evaluated devices or systems.


  • Analysis of Large-Signal Output Capacitance of Transistors Using Sawyer–Tower Circuit

    by Nirmana Perera, Georgios Kampitsis, Remco van Erp, Jessy Ancay, Armin Jafari, Mohammad Samizadeh Nikoo, Elison Matioli

    A detailed analysis of the Sawyer-Tower method used in the measurement of large-signal output capacitance ( C o ) of power transistors is presented, followed by important design recommendations to obtain accurate results. Key factors affecting the proper implementation of the technique, such as power amplifier characteristics, load slew rate, reference capacitor ( C ref ), and reverse conduction of the device, are addressed, with accompanying simulation and experimental results for Si, SiC, and GaN devices. A thorough investigation of the selection of C ref is presented, with a new equation to correctly determine its value for a given voltage swing and output capacitance range of the device under test (DUT). We report that the Sawyer-Tower circuit imposes the DUT to enter steady-state reverse conduction under certain conditions, thus leading to charge-voltage (QV) hysteresis patterns unrelated to C o . Our analysis reveals that the origin of this phenomenon is related to DUT's leakage current and it could be minimized by the proper selection of excitation frequency. This article intends to provide an effective guide on designing and using the Sawyer-Tower circuit, and to induce further scientific insight on characterizing C o .


  • $C_{\text{oss}}$ Loss Tangent of Field-Effect Transistors: Generalizing High-Frequency Soft-Switching Losses

    by Nirmana Perera, Mohammad Samizadeh Nikoo, Armin Jafari, Luca Nela, Elison Matioli

    The dissipated energy (E $diss$ ) related to the resonant charging/discharging of a transistor output capacitance, becomes a dominant loss factor for power converters operating in the MHz range. A recent work has introduced a small-signal measurement method to quantify E $diss$ with a frequency-dependent small-signal resistance, R $_s$ , and an effective small-signal output capacitance, C ${^eff} {_oss}$ . This work provides further insights on the effect of R $s$ and C $_oss$ upon the device losses in a broader sense. In particular, the C $_oss$ loss tangent, tan (δ), is introduced as a normalized E $diss$ to combine the roles of R $s$ and C $_oss$ together with the operating frequency into a single loss parameter. By evaluating commercial device families, it is demonstrated that tan (δ) is constant for a given family, independent of the device on-resistance R $_DS(on)$ . It is shown that a minimum E $diss$ is achieved by having the lowest tan (δ) for a given stored energy (E $_oss$ ) in C $_oss$ . With accompanying guidelines, this work identifies tan (δ) as a powerful figure of merit to classify field-effect transistors for soft-switching applications, regardless of on-resistance variation of devices within a family. The proposed concept provides a comprehensive method to characterize and benchmark power transistors for high-frequency applications.