Luc Le-Tien
Research Subjects
Luc Le-Tien has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Alin Albu-Schaffer
German Aerospace Center (DLR)
4 shared publications Gerd Hirzinger
DLR e. V., Institut für Robotik und Mechatronik, Weßling, Deutschland
1 shared publication- Gerd Hirzinger
Institute of Robotics and Mechatronics, DLR - German Aerospace Center, Wessling, Germany
1 shared publication Klaus Janschek
TU Dresden, Institut für Automatisierungstechnik, Dresden, Deutschland
1 shared publication
Latest Publications
- Open Access
- 18 March 2019
- Published by Publishing House for Science and Technology, Vietnam Academy of Science and Technology (Publications) in Journal of Computer Science and Cybernetics
- Vol. 35 (1) , 85-103
Passive Friction Compensation Using a Nonlinear Disturbance Observer for Flexible Joint Robots with Joint Torque Measurements
The friction and ripple effects from motor and drive cause a major problem for the robot position accuracy, especially for robots with high gear ratio and for high-speed applications. In this paper we introduce a simple, effective, and practical method to compensate for joint friction of flexible joint robots with joint torque sensing, which is based on a nonlinear disturbance observer. This friction observer can increase the performance of the controlled robot system both in terms of the position accuracy and the dynamic behavior. The friction observer needs no friction model and its output corresponds to the low-pass filtered friction torque. Due to the link torque feedback the friction observer can compensate for both friction moment and external moment effects acting on the link. So it can be used not only for position control but also for interaction control, e.g., torque control or impedance control which have low control bandwidth and therefore are sensitive to ripple effects from motor and drive. In addition, its parameter design and parameter optimization are independent of the controller design so that it can be used for friction compensation in conjunction with different controllers designed for flexible joint robots. Furthermore, a passivity analysis is done for this observer-based friction compensation in consideration of Coulomb, viscose and Stribeck friction effects, which is independent of the regulation controller. In combining this friction observer with the state feedback controller \cite{Albu-Schaeffer2}, global asymptotic stability of the controlled system can be shown by using Lyapunov based convergence analysis. Experimental results with robots of the German Aerospace Center (DLR) validate the practical efficiency of the approach.
- 18 March 2019
- Published by Publishing House for Science and Technology, Vietnam Academy of Science and Technology (Publications) in Journal of Computer Science and Cybernetics
- Vol. 35 (1) , 85-103
Open AccessPassive Friction Compensation Using a Nonlinear Disturbance Observer for Flexible Joint Robots with Joint Torque Measurements
The friction and ripple effects from motor and drive cause a major problem for the robot position accuracy, especially for robots with high gear ratio and for high-speed applications. In this paper we introduce a simple, effective, and practical method to compensate for joint friction of flexible joint robots with joint torque sensing, which is based on a nonlinear disturbance observer. This friction observer can increase the performance of the controlled robot system both in terms of the position accuracy and the dynamic behavior. The friction observer needs no friction model and its output corresponds to the low-pass filtered friction torque. Due to the link torque feedback the friction observer can compensate for both friction moment and external moment effects acting on the link. So it can be used not only for position control but also for interaction control, e.g., torque control or impedance control which have low control bandwidth and therefore are sensitive to ripple effects from motor and drive. In addition, its parameter design and parameter optimization are independent of the controller design so that it can be used for friction compensation in conjunction with different controllers designed for flexible joint robots. Furthermore, a passivity analysis is done for this observer-based friction compensation in consideration of Coulomb, viscose and Stribeck friction effects, which is independent of the regulation controller. In combining this friction observer with the state feedback controller \cite{Albu-Schaeffer2}, global asymptotic stability of the controlled system can be shown by using Lyapunov based convergence analysis. Experimental results with robots of the German Aerospace Center (DLR) validate the practical efficiency of the approach.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 26 (6) , 2259-2267
Robust Adaptive Tracking Control Based on State Feedback Controller With Integrator Terms for Elastic Joint Robots With Uncertain Parameters
This brief addresses a robust adaptive control scheme based on a cascaded structure with a full state feedback controller with integrator terms as inner control loop and computed torque as outer control loop for flexible joint robots. Together with integrator effect, the adaptive control law can enhance position accuracy under uncertainties of the robot model, especially, the high friction caused by harmonic drive with high gear ratio. In this brief, the adaptive friction compensation is designed based on the LuGre friction model, which exhibits some advantages compared with the static friction model (e.g., no chattering effect at zero motor velocity). Furthermore, structural oscillations of the link side can be effectively damped by using joint torque feedback in the state feedback controller. Therefore, the proposed adaptive control approach can simultaneously provide high control performance both in terms of the dynamic behavior and the position accuracy. Global asymptotic tracking is achieved for the complete controlled system. The system stability is derived using Lyapunov approaches and Barbalat's lemma. Experimental results validate the practical efficiency of the approach.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 26 (6) , 2259-2267
Robust Adaptive Tracking Control Based on State Feedback Controller With Integrator Terms for Elastic Joint Robots With Uncertain Parameters
This brief addresses a robust adaptive control scheme based on a cascaded structure with a full state feedback controller with integrator terms as inner control loop and computed torque as outer control loop for flexible joint robots. Together with integrator effect, the adaptive control law can enhance position accuracy under uncertainties of the robot model, especially, the high friction caused by harmonic drive with high gear ratio. In this brief, the adaptive friction compensation is designed based on the LuGre friction model, which exhibits some advantages compared with the static friction model (e.g., no chattering effect at zero motor velocity). Furthermore, structural oscillations of the link side can be effectively damped by using joint torque feedback in the state feedback controller. Therefore, the proposed adaptive control approach can simultaneously provide high control performance both in terms of the dynamic behavior and the position accuracy. Global asymptotic tracking is achieved for the complete controlled system. The system stability is derived using Lyapunov approaches and Barbalat's lemma. Experimental results validate the practical efficiency of the approach.
- 23 December 2016
- Published by Taylor & Francis in Advanced Robotics
- Vol. 31 (4) , 1-20
Decoupling and tracking control for elastic joint robots with coupled joint structure
The paper deals with the modeling, identification, and control of a flexible joint robot developed for medical applications at the German Aerospace Center (DLR). In order to design anthropomorphic kinematics, the robot uses a coupled joint structure realized by a differential gearbox, which however leads to strong mechanical couplings inside the coupled joints and must be taken into account. Therefore, a regulation MIMO state feedback controller based on modal analysis is developed for each coupled joint pair, which consists of full state feedback (motor position, link side torque, as well as their derivatives). Furthermore, in order to improve position accuracy and simultaneously keep good dynamic behavior of the MIMO state feedback controller, a cascaded tracking control scheme is proposed, based on the MIMO state feedback controller with additional feedforward terms (desired motor velocity, desired motor acceleration, derivative of the desired torque), which are computed in a computed torque controller and take the whole rigid body dynamics into account. Stability analysis is shown for the complete controlled robot. Finally, experimental results with the DLR medical robot are presented to validate the practical efficiency of the approaches.
- 23 December 2016
- Published by Taylor & Francis in Advanced Robotics
- Vol. 31 (4) , 1-20
Decoupling and tracking control for elastic joint robots with coupled joint structure
The paper deals with the modeling, identification, and control of a flexible joint robot developed for medical applications at the German Aerospace Center (DLR). In order to design anthropomorphic kinematics, the robot uses a coupled joint structure realized by a differential gearbox, which however leads to strong mechanical couplings inside the coupled joints and must be taken into account. Therefore, a regulation MIMO state feedback controller based on modal analysis is developed for each coupled joint pair, which consists of full state feedback (motor position, link side torque, as well as their derivatives). Furthermore, in order to improve position accuracy and simultaneously keep good dynamic behavior of the MIMO state feedback controller, a cascaded tracking control scheme is proposed, based on the MIMO state feedback controller with additional feedforward terms (desired motor velocity, desired motor acceleration, derivative of the desired torque), which are computed in a computed torque controller and take the whole rigid body dynamics into account. Stability analysis is shown for the complete controlled robot. Finally, experimental results with the DLR medical robot are presented to validate the practical efficiency of the approaches.
- 9 September 2010
- Published by Walter de Gruyter GmbH in at - Automatisierungstechnik
- Vol. 58 (9) , 499-511
Entkopplungsregelung und Reibungskompensation für einen Roboter mit elastischen verkoppelten Gelenken
Zusammenfassung: Dieser Beitrag beschreibt die Regelung und Reibungskompensation von Robotern mit elastischen und differentiell getriebenen Gelenken (implementiert am Beispiel des DLR-Medizinroboters). Unter Berücksichtigung der Gelenkverkopplung wird ein MIMO-Zustandsregler (multi-input-multi-output) für die Doppelgelenkstruktur des Medizinroboters eingeführt, der auf der Rückführung der gemessenen Motorpositionen, abtriebsseitigen Drehmomente und deren Ableitungen basiert. Um die Positioniergenauigkeit des Roboters zu verbessern, wird zusätzlich ein Störgrößenbeobachter für die Reibungskompensation entwickelt. Es wird gezeigt, dass der Roboter mit dem MIMO-Zustandsregler und dem Störgrößenbeobachter global asymptotisch stabil ist. Abschließend werden experimentelle Ergebnisse mit dem DLR-Medizinroboter zur Validierung des Ansatzes vorgestellt.
- 9 September 2010
- Published by Walter de Gruyter GmbH in at - Automatisierungstechnik
- Vol. 58 (9) , 499-511
Entkopplungsregelung und Reibungskompensation für einen Roboter mit elastischen verkoppelten Gelenken
Zusammenfassung: Dieser Beitrag beschreibt die Regelung und Reibungskompensation von Robotern mit elastischen und differentiell getriebenen Gelenken (implementiert am Beispiel des DLR-Medizinroboters). Unter Berücksichtigung der Gelenkverkopplung wird ein MIMO-Zustandsregler (multi-input-multi-output) für die Doppelgelenkstruktur des Medizinroboters eingeführt, der auf der Rückführung der gemessenen Motorpositionen, abtriebsseitigen Drehmomente und deren Ableitungen basiert. Um die Positioniergenauigkeit des Roboters zu verbessern, wird zusätzlich ein Störgrößenbeobachter für die Reibungskompensation entwickelt. Es wird gezeigt, dass der Roboter mit dem MIMO-Zustandsregler und dem Störgrößenbeobachter global asymptotisch stabil ist. Abschließend werden experimentelle Ergebnisse mit dem DLR-Medizinroboter zur Validierung des Ansatzes vorgestellt.
- 1 April 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10504729,p. 3824-3830
MIMO State Feedback Controller for a Flexible Joint Robot with Strong Joint Coupling
The paper describes the modeling and control of a robot with flexible joints (the DLR medical robot), which has strong mechanical couplings between pairs of joints realized with a differential gear-box. Because of this coupling, controllers developed before for the DLR light-weight robots cannot be directly applied. The previous control approach is extended in order to allow a multi-input-multi-output (MIMO) design for the strongly coupled joints. Asymptotic stability is shown for the MIMO controller. Finally, experimental results with the DLR medical robot are presented.
- 1 April 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10504729,p. 3824-3830
MIMO State Feedback Controller for a Flexible Joint Robot with Strong Joint Coupling
The paper describes the modeling and control of a robot with flexible joints (the DLR medical robot), which has strong mechanical couplings between pairs of joints realized with a differential gear-box. Because of this coupling, controllers developed before for the DLR light-weight robots cannot be directly applied. The previous control approach is extended in order to allow a multi-input-multi-output (MIMO) design for the strongly coupled joints. Asymptotic stability is shown for the MIMO controller. Finally, experimental results with the DLR medical robot are presented.