Changtai Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Changtai Zhou has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
Heping Xie
State Key Laboratory of Intelligent Construction and Healthy Operation and Maintenance of Deep Underground Engineering, College of Civil and Transportation Engineering Shenzhen University Shenzhen China
5 shared publications- Zhihe Wang
The University of Adelaide
4 shared publications Cunbao Li
State Key Laboratory of Intelligent Construction and Healthy Operation and Maintenance of Deep Underground Engineering, College of Civil and Transportation Engineering Shenzhen University Shenzhen China
3 shared publicationsFei Wang
Guangdong Provincial Key Laboratory of Deep Earth Sciences and Geothermal Energy Exploitation and Utilization, Institute of Deep Earth Sciences and Green Energy, College of Civil and Transportation Engineering, Shenzhen University, Shenzhen, China
3 shared publications- Heping Xie
Institute of Deep Earth Sciences and Green Energy, College of Civil and Transportation Engineering, Shenzhen University, Shenzhen 518060, China
3 shared publications - Jianbo Zhu
State Key Laboratory of Intelligent Construction and Healthy Operation and Maintenance of Deep Underground Engineering College of Civil and Transportation Engineering Shenzhen University Shenzhen China
3 shared publications
Latest Publications
- Open Access
- 22 October 2026
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 13, 1951341
Analysis of multi-hole blasting-induced fracture and fragmentation in coal masses
In this article, the plain strain mode using LS-DYNA is conducted to investigate the coal mass damage evolution under blasting load, and a fragment evaluation method is proposed to optimize mining blasting engineering. The Riedel–Hiermaier–Thoma model is applied and verified in the single-borehole blasting model with a validation parameter. Several blasting models are simulated to reveal the effect of biaxial isobaric stresses, delay explosion, and borehole space on the crack growth pattern. The results indicate that crack growth tends to be restrained with increasing isobaric stresses; in the multi-hole model, the crack tends to fully grow with the increase in delay, and there is an optimal hole spacing for crack growth and fragment formation. Finally, a fragment evaluation method based on damage threshold is proposed to optimize the blasting design in engineering practice.
- 22 October 2026
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 13, 1951341
Open AccessAnalysis of multi-hole blasting-induced fracture and fragmentation in coal masses
In this article, the plain strain mode using LS-DYNA is conducted to investigate the coal mass damage evolution under blasting load, and a fragment evaluation method is proposed to optimize mining blasting engineering. The Riedel–Hiermaier–Thoma model is applied and verified in the single-borehole blasting model with a validation parameter. Several blasting models are simulated to reveal the effect of biaxial isobaric stresses, delay explosion, and borehole space on the crack growth pattern. The results indicate that crack growth tends to be restrained with increasing isobaric stresses; in the multi-hole model, the crack tends to fully grow with the increase in delay, and there is an optimal hole spacing for crack growth and fragment formation. Finally, a fragment evaluation method based on damage threshold is proposed to optimize the blasting design in engineering practice.
- Open Access
- 8 May 2026
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 24
Microwave-enhanced cemented tailings backfill: rheological properties, mechanical behaviors, and physics-informed strength prediction
- 8 May 2026
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 24
Open AccessMicrowave-enhanced cemented tailings backfill: rheological properties, mechanical behaviors, and physics-informed strength prediction
- Open Access
- 1 March 2026
- Published by Wiley in Energy Science & Engineering
- Vol. 14 (5) , 2476-2498
Stress Redistribution Mechanisms and Subsidence Control of Fluidized Gangue Backfilling in Underground Coal Mining: Integrated Experimental and Numerical Investigation
Underground coal extraction creates extensive goafs leading to overlying strata movement and surface subsidence, threatening infrastructure and mining safety. While traditional backfilling methods exist, the specific mechanisms by which fluidized gangue backfilling reduces mining‐induced subsidence remain poorly understood, limiting optimization of design parameters. This study investigates these mechanisms through integrated experimental testing and numerical simulation. Laboratory compression tests on natural caved gangue and composite specimens with varying Talbot indices (0.2–0.8) characterized load‐bearing behavior under uniaxial compression up to 20 MPa. Results reveal that grouting with fluidized backfill slurry enhances initial compression resistance by 50%–70% during early loading phases while maintaining similar ultimate load‐bearing capacity. Numerical simulations using FLAC3D examined stress redistribution and deformation patterns under different backfill thicknesses (0–3 m) and mining advance distances. The primary mechanism identified is effective load transfer through stress redistribution, where composite backfill creates alternative load pathways for redistributing overburden loads across the entire goaf area rather than concentrating forces at discrete pillar locations. Fluidized gangue backfilling with 3 m equivalent thickness reduces maximum stress concentrations by 56.8% and limits surface subsidence to 0.60 m compared to 3.50 m under traditional caving methods. The composite backfill‐pillar co‐bearing system exhibits synergistic load‐sharing effects, with optimal performance achieved when backfill equivalent modulus approaches 60%–70% of coal pillar stiffness. These findings provide quantitative guidance for optimizing fluidized gangue backfilling design, offering a practical solution for subsidence control in underground mining operations.
- 1 March 2026
- Published by Wiley in Energy Science & Engineering
- Vol. 14 (5) , 2476-2498
Open AccessStress Redistribution Mechanisms and Subsidence Control of Fluidized Gangue Backfilling in Underground Coal Mining: Integrated Experimental and Numerical Investigation
Underground coal extraction creates extensive goafs leading to overlying strata movement and surface subsidence, threatening infrastructure and mining safety. While traditional backfilling methods exist, the specific mechanisms by which fluidized gangue backfilling reduces mining‐induced subsidence remain poorly understood, limiting optimization of design parameters. This study investigates these mechanisms through integrated experimental testing and numerical simulation. Laboratory compression tests on natural caved gangue and composite specimens with varying Talbot indices (0.2–0.8) characterized load‐bearing behavior under uniaxial compression up to 20 MPa. Results reveal that grouting with fluidized backfill slurry enhances initial compression resistance by 50%–70% during early loading phases while maintaining similar ultimate load‐bearing capacity. Numerical simulations using FLAC3D examined stress redistribution and deformation patterns under different backfill thicknesses (0–3 m) and mining advance distances. The primary mechanism identified is effective load transfer through stress redistribution, where composite backfill creates alternative load pathways for redistributing overburden loads across the entire goaf area rather than concentrating forces at discrete pillar locations. Fluidized gangue backfilling with 3 m equivalent thickness reduces maximum stress concentrations by 56.8% and limits surface subsidence to 0.60 m compared to 3.50 m under traditional caving methods. The composite backfill‐pillar co‐bearing system exhibits synergistic load‐sharing effects, with optimal performance achieved when backfill equivalent modulus approaches 60%–70% of coal pillar stiffness. These findings provide quantitative guidance for optimizing fluidized gangue backfilling design, offering a practical solution for subsidence control in underground mining operations.
- Open Access
- 14 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (16) , 8960
Advances in Numerical Computation and Mathematical Modeling for Geotechnical Engineering
The field of geotechnical engineering is experiencing a transformative period driven by the increasing complexity of in situ projects and the need for operations in challenging geological environments
- 14 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (16) , 8960
Open AccessAdvances in Numerical Computation and Mathematical Modeling for Geotechnical Engineering
The field of geotechnical engineering is experiencing a transformative period driven by the increasing complexity of in situ projects and the need for operations in challenging geological environments
- Open Access
- 21 July 2025
- Published by Wiley in Deep Underground Science and Engineering
Exploring wave propagation behaviors in rock: A grain‐based perspective on mineral structures
Rock, composed of diverse minerals, exhibits macroscopic mechanical properties largely determined by its grain‐scale structure, making microscale studies crucial for understanding rock dynamic behavior. This study employs a grain‐based model (GBM) within the discrete element method framework, calibrated using Lac du Bonnet granite test results, to investigate wave propagation and attenuation in rock at the grain scale. Using GBM, we analyzed the effects of grain distribution, mineral mechanical properties, and grain size on wave propagation, focusing on peak particle velocity (PPV) attenuation during stress wave propagation. Our results reveal that while the geometric distribution of mineral grains has a limited effect on stress wave propagation, changes in the elastic modulus of minerals significantly impact wave propagation, with higher elastic modulus correlating with lower stress wave attenuation rates. Based on these findings, we propose a PPV attenuation prediction model that effectively captures PPV attenuation behaviors. This study is the first to consider the influence of grains in the study of stress wave propagation, which not only provides novel insights into rock grain‐scale wave propagation and validates the GBM method's applicability in wave propagation research but also proposes an effective PPV attenuation prediction model. The results offer valuable references for practical engineering applications and lay a foundation for future investigations in this field.
- 21 July 2025
- Published by Wiley in Deep Underground Science and Engineering
Open AccessExploring wave propagation behaviors in rock: A grain‐based perspective on mineral structures
Rock, composed of diverse minerals, exhibits macroscopic mechanical properties largely determined by its grain‐scale structure, making microscale studies crucial for understanding rock dynamic behavior. This study employs a grain‐based model (GBM) within the discrete element method framework, calibrated using Lac du Bonnet granite test results, to investigate wave propagation and attenuation in rock at the grain scale. Using GBM, we analyzed the effects of grain distribution, mineral mechanical properties, and grain size on wave propagation, focusing on peak particle velocity (PPV) attenuation during stress wave propagation. Our results reveal that while the geometric distribution of mineral grains has a limited effect on stress wave propagation, changes in the elastic modulus of minerals significantly impact wave propagation, with higher elastic modulus correlating with lower stress wave attenuation rates. Based on these findings, we propose a PPV attenuation prediction model that effectively captures PPV attenuation behaviors. This study is the first to consider the influence of grains in the study of stress wave propagation, which not only provides novel insights into rock grain‐scale wave propagation and validates the GBM method's applicability in wave propagation research but also proposes an effective PPV attenuation prediction model. The results offer valuable references for practical engineering applications and lay a foundation for future investigations in this field.
- Open Access
- 9 January 2025
- Published by Wiley in Deep Underground Science and Engineering
- Vol. 5 (1) , 160-175
Microscopic time‐dependent mechanical behavior of shale derived from nanoindentation
Understanding the microscopic time‐dependent mechanical behavior of shale is critical for assessing macroscopic creep and engineering applications. Grid nanoindentation experiments and nanoindentation creep tests were systematically conducted to investigate microscopic creep behaviors in shale. The indentation creep displacements and creep rates of the shale's soft, intermediate, and hard phases showed the same evolution patterns. The creep deformation was much higher in the soft phase than in the other two phases. However, the difference in the steady‐state creep rates between the three mechanical phases was negligible. A linear relationship was observed between the microscopic contact creep modulus and the microscopic Young's modulus, hardness, creep displacement, and creep rate. The primary mechanism of microscopic creep in shale revealed by the creep strain rate sensitivity parameter was the extension and closure of microcracks. The differences in the microscopic creep parameters derived from the experimental data using the deconvolution methods and representative point methods were evaluated, and the applicability of the two methods was described. The performances of commonly used creep models to predict the microscopic creep behaviors were evaluated. The Burgers model provided the best performance in predicting the steady‐state creep deformation and creep rate. The ability of the Mori–Tanaka and Voigt–Reuss–Hill models to derive macroscopic parameters from microscopic mechanical parameters was compared. Both methods provided macroscopic Young's modulus values close to the experimental values; however, neither could predict macroscopic creep parameters based on microscopic creep parameters.
- 9 January 2025
- Published by Wiley in Deep Underground Science and Engineering
- Vol. 5 (1) , 160-175
Open AccessMicroscopic time‐dependent mechanical behavior of shale derived from nanoindentation
Understanding the microscopic time‐dependent mechanical behavior of shale is critical for assessing macroscopic creep and engineering applications. Grid nanoindentation experiments and nanoindentation creep tests were systematically conducted to investigate microscopic creep behaviors in shale. The indentation creep displacements and creep rates of the shale's soft, intermediate, and hard phases showed the same evolution patterns. The creep deformation was much higher in the soft phase than in the other two phases. However, the difference in the steady‐state creep rates between the three mechanical phases was negligible. A linear relationship was observed between the microscopic contact creep modulus and the microscopic Young's modulus, hardness, creep displacement, and creep rate. The primary mechanism of microscopic creep in shale revealed by the creep strain rate sensitivity parameter was the extension and closure of microcracks. The differences in the microscopic creep parameters derived from the experimental data using the deconvolution methods and representative point methods were evaluated, and the applicability of the two methods was described. The performances of commonly used creep models to predict the microscopic creep behaviors were evaluated. The Burgers model provided the best performance in predicting the steady‐state creep deformation and creep rate. The ability of the Mori–Tanaka and Voigt–Reuss–Hill models to derive macroscopic parameters from microscopic mechanical parameters was compared. Both methods provided macroscopic Young's modulus values close to the experimental values; however, neither could predict macroscopic creep parameters based on microscopic creep parameters.
- Open Access
Study on the Effects of Microwave Heating Time and Power on the Mechanical Properties of Cemented Tailings Backfill
With the escalating demand for advanced and eco-friendly processing technologies in mining engineering, the potential applications of microwave heating technology in the treatment of cement tailings backfill (CTB) are expanding significantly. This research comprehensively investigates the mechanisms through which microwave irradiation duration and power influence the mechanical properties of CTB with varying concentrations and cement-to-sand ratios. The aim is to reveal the influencing patterns through experimental methods, providing scientific evidence for optimizing CTB treatment processes. This paper conducted microwave heating tests, uniaxial compression tests, and SEM-EDS tests on CTB. The research results indicate that heating time and power significantly enhance the early strength of CTB, with a more pronounced effect on CTB with higher concentrations and higher cement–sand ratios. When the heating time is 7 min and the heating power is 340 W, the cement hydration reaction is maximally promoted, thereby increasing the density and strength growth rate of CTB. However, excessively long heating time or overly high heating power may cause microcracks or thermal stress concentration within the CTB, adversely affecting the strength growth rate of CTB. Optimal thermal exposure duration and microwave power settings facilitate the activation of cementitious materials and the nucleation of calcium-silicate-hydrate (C-S-H) phases, thereby accelerating the compressive strength evolution of cemented tailings backfill (CTB). The outcomes of this research offer valuable insights into the deployment of microwave heating methodologies in underground mine backfilling, which are pivotal for augmenting the economic viability and environmental sustainability of mining operations.
Open AccessStudy on the Effects of Microwave Heating Time and Power on the Mechanical Properties of Cemented Tailings Backfill
With the escalating demand for advanced and eco-friendly processing technologies in mining engineering, the potential applications of microwave heating technology in the treatment of cement tailings backfill (CTB) are expanding significantly. This research comprehensively investigates the mechanisms through which microwave irradiation duration and power influence the mechanical properties of CTB with varying concentrations and cement-to-sand ratios. The aim is to reveal the influencing patterns through experimental methods, providing scientific evidence for optimizing CTB treatment processes. This paper conducted microwave heating tests, uniaxial compression tests, and SEM-EDS tests on CTB. The research results indicate that heating time and power significantly enhance the early strength of CTB, with a more pronounced effect on CTB with higher concentrations and higher cement–sand ratios. When the heating time is 7 min and the heating power is 340 W, the cement hydration reaction is maximally promoted, thereby increasing the density and strength growth rate of CTB. However, excessively long heating time or overly high heating power may cause microcracks or thermal stress concentration within the CTB, adversely affecting the strength growth rate of CTB. Optimal thermal exposure duration and microwave power settings facilitate the activation of cementitious materials and the nucleation of calcium-silicate-hydrate (C-S-H) phases, thereby accelerating the compressive strength evolution of cemented tailings backfill (CTB). The outcomes of this research offer valuable insights into the deployment of microwave heating methodologies in underground mine backfilling, which are pivotal for augmenting the economic viability and environmental sustainability of mining operations.
- Open Access
Effect on Top-Coal Mass Failure under Load–Unload Induced by Shield Support
Prior to being released, the top coal of a fully mechanized caving face typically experiences the effects of mining-induced pressure and disturbances from the hydraulic support’s canopy. To investigate the promoting effect of canopy disturbances in the support-controlled area on the damage of top coal during fully mechanized top-coal caving mining, block instability theory and discrete block numerical simulation methods were employed. The instability modes during the initial support and cyclic disturbance stages were analyzed. The fracture evolution and displacement distribution curves were studied for coal bodies with strengths of 3.1 MPa, 15.0 MPa, and 29.5 MPa under the mining influence and support strengths of 0.5 MPa, 1.0 MPa, and 1.5 MPa during the initial support and cyclic disturbance processes. The results showed that during the initial support stage, the instability of the block-structured coal body exhibited four modes as follows: inter-block breakage, inter-block delamination, intra-block fracture expansion, and inter-block sliding. During the cyclic disturbance stage, the coal body instability showed three modes as follows: inter-block sliding, intra-block fracture expansion, and inter-block rotation. The disturbance from the support had little impact on the fragmentation of both low-strength and high-strength coal bodies. However, small support forces combined with multiple cycles of disturbance had an enhancing effect on the instability of medium-strength block-structured top coal.
Open AccessEffect on Top-Coal Mass Failure under Load–Unload Induced by Shield Support
Prior to being released, the top coal of a fully mechanized caving face typically experiences the effects of mining-induced pressure and disturbances from the hydraulic support’s canopy. To investigate the promoting effect of canopy disturbances in the support-controlled area on the damage of top coal during fully mechanized top-coal caving mining, block instability theory and discrete block numerical simulation methods were employed. The instability modes during the initial support and cyclic disturbance stages were analyzed. The fracture evolution and displacement distribution curves were studied for coal bodies with strengths of 3.1 MPa, 15.0 MPa, and 29.5 MPa under the mining influence and support strengths of 0.5 MPa, 1.0 MPa, and 1.5 MPa during the initial support and cyclic disturbance processes. The results showed that during the initial support stage, the instability of the block-structured coal body exhibited four modes as follows: inter-block breakage, inter-block delamination, intra-block fracture expansion, and inter-block sliding. During the cyclic disturbance stage, the coal body instability showed three modes as follows: inter-block sliding, intra-block fracture expansion, and inter-block rotation. The disturbance from the support had little impact on the fragmentation of both low-strength and high-strength coal bodies. However, small support forces combined with multiple cycles of disturbance had an enhancing effect on the instability of medium-strength block-structured top coal.
- Top Cited PapersOpen Access
- 8 April 2024
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 57 (8) , 6183-6209
Uncovering Failure and Cracking Behaviors of Double-Flawed Sandstone Under Compressive-Shear Loading Using Digital Image Correlation (DIC) Technique
The coalescence of flaws provides valuable insights into the failure behaviors of rock masses, which is a critical issue in rock engineering. In this study, a series of compressive-shear tests were conducted on sandstone specimens containing double flaws. The failure and cracking behaviors of specimens with different geometric configurations under various loading conditions were analyzed using the digital image correlation (DIC) technique. The strain and displacement fields effectively demonstrate crack propagation and coalescence, accompanied by the axial load–displacement curve. The results revealed the effect of eccentric and overlapping distance of double flaws on the compressive-shear bearing capacity. The relative displacement method (RDM) was applied to analyze the crack characteristics in this study. Based on the relative displacement behaviors of the cracks, five typical types of crack modes were identified, including tensile mode, shear mode, mixed-I mode, mixed-II mode, and mixed-III mode. Both wing cracks initiated from flaw outer tips and anti-wing cracks generated from flaw inner tips were classified as a tensile mode or mode-I, dominated by normal relative displacement. In contrast, the secondary cracks were categorized as either shear mode or mode-III, which are dominated by tangential relative displacement. The geometry configurations of flaws affected both the coalescent mode and cracking path, which in turn influenced the failure mode of specimens. This study identified and summarized eight types of coalescent modes between double flaws. The findings presented in this paper contribute to a better understanding of the failure behavior of rock masses containing flaws subjected to compressive-shear loads.
- 8 April 2024
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 57 (8) , 6183-6209
Top Cited PapersOpen AccessUncovering Failure and Cracking Behaviors of Double-Flawed Sandstone Under Compressive-Shear Loading Using Digital Image Correlation (DIC) Technique
The coalescence of flaws provides valuable insights into the failure behaviors of rock masses, which is a critical issue in rock engineering. In this study, a series of compressive-shear tests were conducted on sandstone specimens containing double flaws. The failure and cracking behaviors of specimens with different geometric configurations under various loading conditions were analyzed using the digital image correlation (DIC) technique. The strain and displacement fields effectively demonstrate crack propagation and coalescence, accompanied by the axial load–displacement curve. The results revealed the effect of eccentric and overlapping distance of double flaws on the compressive-shear bearing capacity. The relative displacement method (RDM) was applied to analyze the crack characteristics in this study. Based on the relative displacement behaviors of the cracks, five typical types of crack modes were identified, including tensile mode, shear mode, mixed-I mode, mixed-II mode, and mixed-III mode. Both wing cracks initiated from flaw outer tips and anti-wing cracks generated from flaw inner tips were classified as a tensile mode or mode-I, dominated by normal relative displacement. In contrast, the secondary cracks were categorized as either shear mode or mode-III, which are dominated by tangential relative displacement. The geometry configurations of flaws affected both the coalescent mode and cracking path, which in turn influenced the failure mode of specimens. This study identified and summarized eight types of coalescent modes between double flaws. The findings presented in this paper contribute to a better understanding of the failure behavior of rock masses containing flaws subjected to compressive-shear loads.