Michael D. Sinanis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Michael D. Sinanis has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
Dimitrios Peroulis
School of Electrical and Computer Engineering and Birck Nanotechnology Center Purdue University, West Lafayette, 47907, USA
7 shared publications- Dimitrios Peroulis
Elmore Family School of Electrical and Computer Engineering, Purdue University, West Lafayette, USA
7 shared publications - Mahmoud Abdelfattah
School of Electrical and Computer Engineering, Birck Nanotechnology Center, Purdue University, West Lafayette, IN 47907, USA
5 shared publications - Mohammad Abu Khater
School of Electrical and Computer Engineering, Purdue University, West Lafayette, IN, USA
5 shared publications - Ahmed Abdelraheem
Military Technical College
2 shared publications - Alden Fisher
Elmore Family School of Electrical and Computer Engineering, Purdue University, West Lafayette, IN, USA
2 shared publications
Latest Publications
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (4) , 2389-2403
Power-Handling Considerations of Narrowband Second-Order Absorptive and Reflective Bandstop Filters
This article compares the power-handling capabilities of narrowband second-order absorptive bandstop and reflective bandstop filters (BSFs) that have not been explored previously. The analysis considers two distinct perspectives: the maximum voltage and current that each filter can handle, as well as the average power dissipation. Both electrical and electrothermal analyses are conducted. Closed-form expressions are derived for the second-order absorptive and reflective BSF (RBSF) topologies, delineating voltage and power distribution among their resonators as a function of input power. Two second-order microstrip filters with lumped components are designed, fabricated, and measured to validate the analyses. These filters, centered at 500 MHz, are tailored specifically for direct, nonloading voltage measurement using an oscilloscope. Thermal profile measurements are also taken using an infrared (IR) camera, confirming theoretical trends that the absorptive BSF (ABSF) has a higher average power-handling capability (PHC) compared to the RBSF.
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (4) , 2389-2403
Power-Handling Considerations of Narrowband Second-Order Absorptive and Reflective Bandstop Filters
This article compares the power-handling capabilities of narrowband second-order absorptive bandstop and reflective bandstop filters (BSFs) that have not been explored previously. The analysis considers two distinct perspectives: the maximum voltage and current that each filter can handle, as well as the average power dissipation. Both electrical and electrothermal analyses are conducted. Closed-form expressions are derived for the second-order absorptive and reflective BSF (RBSF) topologies, delineating voltage and power distribution among their resonators as a function of input power. Two second-order microstrip filters with lumped components are designed, fabricated, and measured to validate the analyses. These filters, centered at 500 MHz, are tailored specifically for direct, nonloading voltage measurement using an oscilloscope. Thermal profile measurements are also taken using an infrared (IR) camera, confirming theoretical trends that the absorptive BSF (ABSF) has a higher average power-handling capability (PHC) compared to the RBSF.
- 6 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 24 (7) , 61-67
EVAding Interference: A Hybrid Architecture Approach for Substrate-Integrated Evanescent-Mode Cavity Filters
In today’s crowded RF spectrum, receivers must be highly selective to mitigate any interference, whether intentional or from adjacent channels. The upper part of the C band (4–8 GHz) has been designated for space-to-Earth satellite communications and space exploration [1] . This long-range communication demands sensitive, low-loss receivers that can recover weak signals. Customarily, a tradeoff between size and performance presents itself, which poses a challenge to the microwave community as size is often critical in satellite payloads. Therefore, a compact, radiation-impervious filtering solution is needed.
- 6 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 24 (7) , 61-67
EVAding Interference: A Hybrid Architecture Approach for Substrate-Integrated Evanescent-Mode Cavity Filters
In today’s crowded RF spectrum, receivers must be highly selective to mitigate any interference, whether intentional or from adjacent channels. The upper part of the C band (4–8 GHz) has been designated for space-to-Earth satellite communications and space exploration [1] . This long-range communication demands sensitive, low-loss receivers that can recover weak signals. Customarily, a tradeoff between size and performance presents itself, which poses a challenge to the microwave community as size is often critical in satellite payloads. Therefore, a compact, radiation-impervious filtering solution is needed.
- 3 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 831-834
A W-Band SPDT Photoconductive Evanescent-Mode Waveguide Switch
This letter presents the design, fabrication, and measurement of a silicon micromachined photoconductive evanescent (EVA)-mode waveguide switch operating in a single-pole double-throw (SPDT) configuration. Two EVA-mode waveguides loaded with silicon posts are placed in a Y configuration with a common feeding waveguide. In the absence of photoexcitation, the dielectric posts and EVA channel exhibit a bandpass filter response that allows low-loss propagation of signals on the order of 2.0 dB at 96.7 GHz. When photoexcited, the low conductive posts and EVA channel yield a very high isolation of 36.5 dB up to 102.4 GHz within $W$ -band. The proposed design shows promise for 5G and 6G communication backhaul devices.
- 3 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 831-834
A W-Band SPDT Photoconductive Evanescent-Mode Waveguide Switch
This letter presents the design, fabrication, and measurement of a silicon micromachined photoconductive evanescent (EVA)-mode waveguide switch operating in a single-pole double-throw (SPDT) configuration. Two EVA-mode waveguides loaded with silicon posts are placed in a Y configuration with a common feeding waveguide. In the absence of photoexcitation, the dielectric posts and EVA channel exhibit a bandpass filter response that allows low-loss propagation of signals on the order of 2.0 dB at 96.7 GHz. When photoexcited, the low conductive posts and EVA channel yield a very high isolation of 36.5 dB up to 102.4 GHz within $W$ -band. The proposed design shows promise for 5G and 6G communication backhaul devices.
- Open Access
- 2 February 2023
- Published by Wiley in Advanced Physics Research
- Vol. 4 (3)
Employing Topological Properties of Phase Singularities for Designing Supercavity Systems with Tailored Excitation
Trapping electromagnetic waves in high‐index resonators with extreme quality factors (Q‐factor) can be achieved by exciting supercavity (quasi‐bound states in the continuum, quasi‐BIC) modes with minimal radiation loss. Conventionally, the quasi‐BICs are achieved by tuning the resonator dimensions to promote destructive interference between two modes in the cavity. In this work, an enhanced Q‐factor is achieved by manipulating the structure of a near‐field excitation source and tailoring the excitation strength of individual multipolar modes. A pair of concentric rings with strong mutual coupling is used in contrast to a simple single‐ring case. We show that adding the second passive ring enables additional degrees of freedom to manipulate the multipolar content exited in the cavity. The multipole decomposition of the cavity modes is performed using full‐wave numerical simulations to support these claims. Experimental validation with a double‐ring fed supercavity demonstrates the highest measured Q‐factor of ≈310 or ≈2× the quality factor of a design without supercavity, which is consistent with a numerical model predicting up to 3× enhanced Q‐factor. We show that, analyses of polarization singularities and multipolar decomposition can be used to understand, characterize, and design such systems, employing their topological properties not broadly explored before.
- 2 February 2023
- Published by Wiley in Advanced Physics Research
- Vol. 4 (3)
Open AccessEmploying Topological Properties of Phase Singularities for Designing Supercavity Systems with Tailored Excitation
Trapping electromagnetic waves in high‐index resonators with extreme quality factors (Q‐factor) can be achieved by exciting supercavity (quasi‐bound states in the continuum, quasi‐BIC) modes with minimal radiation loss. Conventionally, the quasi‐BICs are achieved by tuning the resonator dimensions to promote destructive interference between two modes in the cavity. In this work, an enhanced Q‐factor is achieved by manipulating the structure of a near‐field excitation source and tailoring the excitation strength of individual multipolar modes. A pair of concentric rings with strong mutual coupling is used in contrast to a simple single‐ring case. We show that adding the second passive ring enables additional degrees of freedom to manipulate the multipolar content exited in the cavity. The multipole decomposition of the cavity modes is performed using full‐wave numerical simulations to support these claims. Experimental validation with a double‐ring fed supercavity demonstrates the highest measured Q‐factor of ≈310 or ≈2× the quality factor of a design without supercavity, which is consistent with a numerical model predicting up to 3× enhanced Q‐factor. We show that, analyses of polarization singularities and multipolar decomposition can be used to understand, characterize, and design such systems, employing their topological properties not broadly explored before.
- Open Access
- 16 May 2022
- Published by Oxford University Press (OUP) in PNAS Nexus
- Vol. 1 (3) , pgac052
Statistical electromagnetics for industrial pharmaceutical lyophilization
Lyophilization is a common unit operation in pharmaceutical manufacturing but is a prolonged vacuum drying process with poor energy utilization. Microwave-assisted vacuum drying has been investigated to accelerate the lyophilization process. However, the literature lacks methodical approaches that consider the lyophilizer, the lyophilizate, the microwave power uniformity, the resulting heat uniformity, and the scalability. We present a microwave–vacuum drying method based on the statistical electromagnetics theory. The method offers an optimum frequency selection procedure that accounts for the lyophilizer and the lyophilizate. The 2.45 GHz frequency conventionally utilized is proven to be far from optimum. The method is applied in a microwave-assisted heating configuration to pharmaceutical excipients (sucrose and mannitol) and different myoglobin formulations in a lab-scale lyophilizer. At 18 GHz frequency and 60 W microwave power, the method shows nearly three times speed-up in the primary drying stage of sucrose relative to the conventional lyophilization cycle for typical laboratory batches. The uniformity of the microwave power inside the chamber is controlled within ± 1 dB. The resulting heating uniformity measured through residual moisture analysis shows 12.7% of normalized SD of moisture level across the batch in a microwave-assisted cycle as opposed to 15.3% in the conventional cycle. Conventional and microwave lyophilized formulations are characterized using solid-state hydrogen-deuterium exchange-mass spectrometry (ssHDX-MS), solid-state Fourier transform infrared spectroscopy (ssFTIR), circular dichroism (CD), and accelerated stability testing (AST). Characterization shows comparable protein structure and stability. Heat and mass transfer simulations quantify further effects of optimal volumetric heating via the high-frequency statistical microwave heating.
- 16 May 2022
- Published by Oxford University Press (OUP) in PNAS Nexus
- Vol. 1 (3) , pgac052
Open AccessStatistical electromagnetics for industrial pharmaceutical lyophilization
Lyophilization is a common unit operation in pharmaceutical manufacturing but is a prolonged vacuum drying process with poor energy utilization. Microwave-assisted vacuum drying has been investigated to accelerate the lyophilization process. However, the literature lacks methodical approaches that consider the lyophilizer, the lyophilizate, the microwave power uniformity, the resulting heat uniformity, and the scalability. We present a microwave–vacuum drying method based on the statistical electromagnetics theory. The method offers an optimum frequency selection procedure that accounts for the lyophilizer and the lyophilizate. The 2.45 GHz frequency conventionally utilized is proven to be far from optimum. The method is applied in a microwave-assisted heating configuration to pharmaceutical excipients (sucrose and mannitol) and different myoglobin formulations in a lab-scale lyophilizer. At 18 GHz frequency and 60 W microwave power, the method shows nearly three times speed-up in the primary drying stage of sucrose relative to the conventional lyophilization cycle for typical laboratory batches. The uniformity of the microwave power inside the chamber is controlled within ± 1 dB. The resulting heating uniformity measured through residual moisture analysis shows 12.7% of normalized SD of moisture level across the batch in a microwave-assisted cycle as opposed to 15.3% in the conventional cycle. Conventional and microwave lyophilized formulations are characterized using solid-state hydrogen-deuterium exchange-mass spectrometry (ssHDX-MS), solid-state Fourier transform infrared spectroscopy (ssFTIR), circular dichroism (CD), and accelerated stability testing (AST). Characterization shows comparable protein structure and stability. Heat and mass transfer simulations quantify further effects of optimal volumetric heating via the high-frequency statistical microwave heating.
- Open Access
- 15 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 19643-19653
High-Q High Power Tunable Filters Manufactured With Injection Molding Technology
This paper presents the first demonstration of injection molding technology to enable large-scale mass manufacturing of high-performance tunable microwave filters to meet the growing needs of 5G small cell stations. This is the first time that a tunable filter satisfies all four of the following requirements simultaneously: low manufacturing cost, high quality factor, wide tuning range, and high power handling. Exhaustive research exists on the use of polymers for 3D microwave device manufacturing; nonetheless, mass-production technologies, such as injection molding, can provide low costs without compromising performance. The proposed bandpass filter implementation uses a tunable evanescent-mode cavity resonator injection molded with an acrylonitrile-butadiene-styrene thermoplastic polymer. In addition, changing the critical gap size over the resonator’s post using a commercial microactuator provides frequency tuning. The measured filter achieves an 86% tuning range from 2.8 - 5.2 GHz with a state-of-the-art measured unloaded quality factor Qu of 1548 - 2573. The filter has a measured insertion loss of 0.06 -0.1 dB with a fractional bandwidth from 7.6 -8.4% across the entire tuning range. Moreover, for the first time in this manufacturing technology implementation, a bandpass filter is demonstrated with power handling capabilities beyond 100 W. The manufactured device demonstrates the significant potential of this technology for the scale-up manufacturing of reconfigurable high-Q RF filters without compromising the performance.
- 15 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 19643-19653
Open AccessHigh-Q High Power Tunable Filters Manufactured With Injection Molding Technology
This paper presents the first demonstration of injection molding technology to enable large-scale mass manufacturing of high-performance tunable microwave filters to meet the growing needs of 5G small cell stations. This is the first time that a tunable filter satisfies all four of the following requirements simultaneously: low manufacturing cost, high quality factor, wide tuning range, and high power handling. Exhaustive research exists on the use of polymers for 3D microwave device manufacturing; nonetheless, mass-production technologies, such as injection molding, can provide low costs without compromising performance. The proposed bandpass filter implementation uses a tunable evanescent-mode cavity resonator injection molded with an acrylonitrile-butadiene-styrene thermoplastic polymer. In addition, changing the critical gap size over the resonator’s post using a commercial microactuator provides frequency tuning. The measured filter achieves an 86% tuning range from 2.8 - 5.2 GHz with a state-of-the-art measured unloaded quality factor Qu of 1548 - 2573. The filter has a measured insertion loss of 0.06 -0.1 dB with a fractional bandwidth from 7.6 -8.4% across the entire tuning range. Moreover, for the first time in this manufacturing technology implementation, a bandpass filter is demonstrated with power handling capabilities beyond 100 W. The manufactured device demonstrates the significant potential of this technology for the scale-up manufacturing of reconfigurable high-Q RF filters without compromising the performance.
- 18 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (7) , 1291-1300
Design, Fabrication, and Characterization of a Compact Hierarchical Manifold Microchannel Heat Sink Array for Two-Phase Cooling
High-heat-flux removal is critical for next-generation electronic devices to reliably operate within their temperature limits. A large portion of the thermal resistance in a traditional chip package is caused by thermal resistances at interfaces between the device, heat spreaders, and the heat sink; embedding the heat sink directly into the heat-generating device can eliminate these interface resistances and drastically reduce the overall thermal resistance. Microfluidic cooling within the embedded heat sink improves heat dissipation, with two-phase operation offering the potential for dissipation of very high heat fluxes while maintaining moderate chip temperatures. To enable multi-chip stacking and other heterogeneous packaging approaches, it is important to densely integrate all fluid flow paths into the device; volumetric heat dissipation emerges as a performance metric in this new heat sinking paradigm. In this work, a compact hierarchical manifold microchannel (MMC) design is presented that utilizes an integrated multi-level manifold distributor to feed coolant to an array of microchannel heat sinks. The flow features in the manifold layers and microchannels are fabricated in silicon wafers using deep reactive ion etching. The heat source is simulated via Joule heating using thin-film platinum heaters. On-chip spatial temperature measurements are made using four-wire resistance temperature detectors. Individual manifold layers and the microchannel-bearing wafers are diced and bonded into a sealed stack via thermocompression bonding using gold layers at the mating surfaces. Thermal and hydrodynamic testing is performed by pumping the dielectric fluid HFE-7100 through the device at a known flow rate, temperature, and pressure at different levels of chip heat input. A volumetric heat density of up to 2870 W/cm3 is dissipated at a chip temperature less than 112 °C and microchannel pressure drop less than 27 kPa. The overall pressure drop is governed by flow through the manifold, rather than the microchannels, in this compact heat sink that occupies envelope of 5 mm × 5 mm × 2.3 mm including all functional flow features.
- 18 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (7) , 1291-1300
Design, Fabrication, and Characterization of a Compact Hierarchical Manifold Microchannel Heat Sink Array for Two-Phase Cooling
High-heat-flux removal is critical for next-generation electronic devices to reliably operate within their temperature limits. A large portion of the thermal resistance in a traditional chip package is caused by thermal resistances at interfaces between the device, heat spreaders, and the heat sink; embedding the heat sink directly into the heat-generating device can eliminate these interface resistances and drastically reduce the overall thermal resistance. Microfluidic cooling within the embedded heat sink improves heat dissipation, with two-phase operation offering the potential for dissipation of very high heat fluxes while maintaining moderate chip temperatures. To enable multi-chip stacking and other heterogeneous packaging approaches, it is important to densely integrate all fluid flow paths into the device; volumetric heat dissipation emerges as a performance metric in this new heat sinking paradigm. In this work, a compact hierarchical manifold microchannel (MMC) design is presented that utilizes an integrated multi-level manifold distributor to feed coolant to an array of microchannel heat sinks. The flow features in the manifold layers and microchannels are fabricated in silicon wafers using deep reactive ion etching. The heat source is simulated via Joule heating using thin-film platinum heaters. On-chip spatial temperature measurements are made using four-wire resistance temperature detectors. Individual manifold layers and the microchannel-bearing wafers are diced and bonded into a sealed stack via thermocompression bonding using gold layers at the mating surfaces. Thermal and hydrodynamic testing is performed by pumping the dielectric fluid HFE-7100 through the device at a known flow rate, temperature, and pressure at different levels of chip heat input. A volumetric heat density of up to 2870 W/cm3 is dissipated at a chip temperature less than 112 °C and microchannel pressure drop less than 27 kPa. The overall pressure drop is governed by flow through the manifold, rather than the microchannels, in this compact heat sink that occupies envelope of 5 mm × 5 mm × 2.3 mm including all functional flow features.
- 13 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 20 (1) , 62-69
A Flexible Virtual Battery: A Wearable Wireless Energy Harvester
Continuous advancements in the domains of biomedical sensors, Internet of Things (IoT) devices, in vivo sensors, and other similar technologies have created a great need to miniaturize portable and end-user devices, especially their powering circuitry. Nearly all devices and sensors require a powering mechanism to obtain, process, and/or transmit information. For example, [1] discusses a flexible gastric battery and a wireless power link that can replace traditional bulky batteries and reduce the size of the wireless capsule. Low-power circuit solutions are of paramount importance for wearable and implantable devices to reduce battery size and improve user comfort [2]. Harvesting the available unused microwave energy from, e.g., Wi-Fi and cellular signals seems a promising solution for replacing a conventional battery with a virtual battery. This term has been used in [3] to describe RF-to-dc converters that are able to power small, portable RF applications for a reasonably long time in the absence of a direct illuminating RF field.
- 13 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 20 (1) , 62-69
A Flexible Virtual Battery: A Wearable Wireless Energy Harvester
Continuous advancements in the domains of biomedical sensors, Internet of Things (IoT) devices, in vivo sensors, and other similar technologies have created a great need to miniaturize portable and end-user devices, especially their powering circuitry. Nearly all devices and sensors require a powering mechanism to obtain, process, and/or transmit information. For example, [1] discusses a flexible gastric battery and a wireless power link that can replace traditional bulky batteries and reduce the size of the wireless capsule. Low-power circuit solutions are of paramount importance for wearable and implantable devices to reduce battery size and improve user comfort [2]. Harvesting the available unused microwave energy from, e.g., Wi-Fi and cellular signals seems a promising solution for replacing a conventional battery with a virtual battery. This term has been used in [3] to describe RF-to-dc converters that are able to power small, portable RF applications for a reasonably long time in the absence of a direct illuminating RF field.
- 2 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (12) , 5563-5572
Ultra-Compact Tunable Filtering Rat-Race Coupler Based on Half-Mode SIW Evanescent-Mode Cavity Resonators
In this paper, for the first time, an ultra-compact frequency-tunable filtering rat-race coupler based on half-mode evanescent-mode (EVA) cavity resonators is presented. Employing EVA cavity resonators in the coupler design yields attractive characteristics, such as a wide tuning range and a wide spurious-free range, while also adding filtering functionality to the device. The presented coupler is synthesized as a two pole bandpass filter using the coupling matrix method. Then, the coupling coefficients are mapped to a coupler topology. Design, simulations, and experimental validation are presented. The implemented rat-race coupler has a very compact size [0.14λgx0.14λg (λg at 885 MHz)] achieving a 92% miniaturization in the structure footprint compared to the conventional planar one. The coupler has an 86% tuning range ranging between 0.885-1.65 GHz. Throughout the tuning range, the coupler shows an equal power splitting ratio and filtering profile with a measured insertion loss and 3-dB fractional bandwidth between 5 and 4.2 dB and 6.8% and 8%, respectively. The measured isolation is better than 30 dB. In addition, the coupler has a measured spurious-free range of 10.2fₒ (at the lowest frequency) to 5.45fₒ (at the highest frequency).
- 2 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (12) , 5563-5572
Ultra-Compact Tunable Filtering Rat-Race Coupler Based on Half-Mode SIW Evanescent-Mode Cavity Resonators
In this paper, for the first time, an ultra-compact frequency-tunable filtering rat-race coupler based on half-mode evanescent-mode (EVA) cavity resonators is presented. Employing EVA cavity resonators in the coupler design yields attractive characteristics, such as a wide tuning range and a wide spurious-free range, while also adding filtering functionality to the device. The presented coupler is synthesized as a two pole bandpass filter using the coupling matrix method. Then, the coupling coefficients are mapped to a coupler topology. Design, simulations, and experimental validation are presented. The implemented rat-race coupler has a very compact size [0.14λgx0.14λg (λg at 885 MHz)] achieving a 92% miniaturization in the structure footprint compared to the conventional planar one. The coupler has an 86% tuning range ranging between 0.885-1.65 GHz. Throughout the tuning range, the coupler shows an equal power splitting ratio and filtering profile with a measured insertion loss and 3-dB fractional bandwidth between 5 and 4.2 dB and 6.8% and 8%, respectively. The measured isolation is better than 30 dB. In addition, the coupler has a measured spurious-free range of 10.2fₒ (at the lowest frequency) to 5.45fₒ (at the highest frequency).
- 24 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (12) , 5605-5613
Monitoring and Control of MEMS Tunable Filters Using Inductive Proximity Sensing
- 24 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (12) , 5605-5613
Monitoring and Control of MEMS Tunable Filters Using Inductive Proximity Sensing