Amy Mensch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amy Mensch has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Karen A. Thole
Pennsylvania State University Department of Mechanical Engineering 3127 Research Drive, State College, PA 16801
7 shared publications Karen A. Thole
The Pennsylvania State University, University Park, PA
3 shared publicationsRobert J. Santoro
2 shared publications- Seong-Young Lee
Michigan Technological University
2 shared publications Anthony Hamins
National Institute of Standards and Technology, 100 Bureau Dr., Gaithersburg, 20899, MD, USA
1 shared publication- Anthony Hamins
National Institute of Standards and Technology
1 shared publication
Latest Publications
- 25 May 2026
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 148 (8)
Experimental Investigation of Factors Affecting Individual Firebrand Heat Transfer
Firebrand ignition is a significant contributor to the spread of wildfires into communities. This study investigates effects of flow velocity, firebrand wood type and size, and substrate material on the peak heat flux and total heat transfer from individual disk-shaped firebrands. Firebrand heat transfer to a surface is measured with a thin skin calorimeter embedded in the substrate. Peak heat fluxes were between 22 kW/m2 and 84 kW/m2 and were higher for the smaller radius firebrands. The total heating to the substrate also tended to be higher for the smaller radius firebrands, but was about the same for the two substrate materials tested. Notably, flow velocity had almost no impact on peak heat flux, and higher velocities increased the total heating only for some firebrand wood types. Two correlations were determined to predict peak heat flux and total heating based on experimental parameters, which included the measured firebrand temperature. These correlations confirmed the importance of substrate properties on firebrand heat transfer.
- 25 May 2026
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 148 (8)
Experimental Investigation of Factors Affecting Individual Firebrand Heat Transfer
Firebrand ignition is a significant contributor to the spread of wildfires into communities. This study investigates effects of flow velocity, firebrand wood type and size, and substrate material on the peak heat flux and total heat transfer from individual disk-shaped firebrands. Firebrand heat transfer to a surface is measured with a thin skin calorimeter embedded in the substrate. Peak heat fluxes were between 22 kW/m2 and 84 kW/m2 and were higher for the smaller radius firebrands. The total heating to the substrate also tended to be higher for the smaller radius firebrands, but was about the same for the two substrate materials tested. Notably, flow velocity had almost no impact on peak heat flux, and higher velocities increased the total heating only for some firebrand wood types. Two correlations were determined to predict peak heat flux and total heating based on experimental parameters, which included the measured firebrand temperature. These correlations confirmed the importance of substrate properties on firebrand heat transfer.
- 26 March 2026
- Published by Elsevier in Fire Safety Journal
- Vol. 162
Smoke production and detection from lithium ion battery powered e-scooter fires in a compartment
- 26 March 2026
- Published by Elsevier in Fire Safety Journal
- Vol. 162
Smoke production and detection from lithium ion battery powered e-scooter fires in a compartment
- 25 March 2026
- Published by Elsevier in Fire Safety Journal
- Vol. 162
A comparison of photoacoustic and grayscale measurements of soot deposition on surfaces
- 25 March 2026
- Published by Elsevier in Fire Safety Journal
- Vol. 162
A comparison of photoacoustic and grayscale measurements of soot deposition on surfaces
- 11 July 2023
- Published by Elsevier in Fire Safety Journal
- Vol. 140
Measuring firebrand heat flux with a thin-skin calorimeter
- 11 July 2023
- Published by Elsevier in Fire Safety Journal
- Vol. 140
Measuring firebrand heat flux with a thin-skin calorimeter
- 18 March 2021
- Published by Springer Nature in Fire Technology
- Vol. 57 (6) , 2981-3004
Sensors and Machine Learning Models to Prevent Cooktop Ignition and Ignore Normal Cooking
- 18 March 2021
- Published by Springer Nature in Fire Technology
- Vol. 57 (6) , 2981-3004
Sensors and Machine Learning Models to Prevent Cooktop Ignition and Ignore Normal Cooking
- 1 November 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 143
Measurements and predictions of thermophoretic soot deposition
- 1 November 2019
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 143
Measurements and predictions of thermophoretic soot deposition
- 22 December 2015
- Published by Wiley in Journal of Turbomachinery
- Vol. 138 (3) , 031007
Overall Effectiveness and Flowfield Measurements for an Endwall With Nonaxisymmetric Contouring
Endwall contouring is a technique used to reduce the strength and development of three-dimensional secondary flows in a turbine vane or blade passage in a gas turbine. The secondary flows locally affect the external heat transfer, particularly on the endwall surface. The combination of external and internal convective heat transfer, along with solid conduction, determines component temperatures, which affect the service life of turbine components. A conjugate heat transfer model is used to measure the nondimensional external surface temperature, known as overall effectiveness, of an endwall with nonaxisymmetric contouring. The endwall cooling methods include internal impingement cooling and external film cooling. Measured values of overall effectiveness show that endwall contouring reduces the effectiveness of impingement alone, but increases the effectiveness of film cooling alone. Given the combined case of both impingement and film cooling, the laterally averaged overall effectiveness is not significantly changed between the flat and the contoured endwalls. Flowfield measurements indicate that the size and location of the passage vortex changes as film cooling is added and as the blowing ratio increases. Because endwall contouring can produce local effects on internal cooling and film cooling performance, the implications for heat transfer should be considered in endwall contour designs.
- 22 December 2015
- Published by Wiley in Journal of Turbomachinery
- Vol. 138 (3) , 031007
Overall Effectiveness and Flowfield Measurements for an Endwall With Nonaxisymmetric Contouring
Endwall contouring is a technique used to reduce the strength and development of three-dimensional secondary flows in a turbine vane or blade passage in a gas turbine. The secondary flows locally affect the external heat transfer, particularly on the endwall surface. The combination of external and internal convective heat transfer, along with solid conduction, determines component temperatures, which affect the service life of turbine components. A conjugate heat transfer model is used to measure the nondimensional external surface temperature, known as overall effectiveness, of an endwall with nonaxisymmetric contouring. The endwall cooling methods include internal impingement cooling and external film cooling. Measured values of overall effectiveness show that endwall contouring reduces the effectiveness of impingement alone, but increases the effectiveness of film cooling alone. Given the combined case of both impingement and film cooling, the laterally averaged overall effectiveness is not significantly changed between the flat and the contoured endwalls. Flowfield measurements indicate that the size and location of the passage vortex changes as film cooling is added and as the blowing ratio increases. Because endwall contouring can produce local effects on internal cooling and film cooling performance, the implications for heat transfer should be considered in endwall contour designs.
- 8 December 2015
- Published by Springer Nature in Experiments in Fluids
- Vol. 57 (1) , 1-16
Effects of non-axisymmetric endwall contouring and film cooling on the passage flowfield in a linear turbine cascade
- 8 December 2015
- Published by Springer Nature in Experiments in Fluids
- Vol. 57 (1) , 1-16
Effects of non-axisymmetric endwall contouring and film cooling on the passage flowfield in a linear turbine cascade
- 18 August 2015
- Published by Wiley in Journal of Turbomachinery
- Vol. 137 (11) , 111002
Simulations of Multiphase Particle Deposition on a Gas Turbine Endwall With Impingement and Film Cooling
Replacing natural gas fuels with coal-derived syngas in industrial gas turbines can lead to molten particle deposition on the turbine components. The deposition of the particles, which originate from impurities in the syngas fuels, can increase surface roughness and obstruct film cooling holes. These deposition effects increase heat transfer to the components and degrade the performance of cooling mechanisms, which are critical for maintaining component life. The current experimental study dynamically simulated molten particle deposition on a conducting blade endwall with the injection of molten wax. The key nondimensional parameters for modeling of conjugate heat transfer and deposition were replicated in the experiment. The endwall was cooled with internal impingement jet cooling and film cooling. Increasing blowing ratio mitigated some deposition at the film cooling hole exits and in areas of coolest endwall temperatures. After deposition, the external surface temperatures and internal endwall temperatures were measured and found to be warmer than the endwall temperatures measured before deposition. Although the deposition helps insulate the endwall from the mainstream, the roughness effects of the deposition counteract the insulating effect by decreasing the benefit of film cooling and by increasing external heat transfer coefficients.
- 18 August 2015
- Published by Wiley in Journal of Turbomachinery
- Vol. 137 (11) , 111002
Simulations of Multiphase Particle Deposition on a Gas Turbine Endwall With Impingement and Film Cooling
Replacing natural gas fuels with coal-derived syngas in industrial gas turbines can lead to molten particle deposition on the turbine components. The deposition of the particles, which originate from impurities in the syngas fuels, can increase surface roughness and obstruct film cooling holes. These deposition effects increase heat transfer to the components and degrade the performance of cooling mechanisms, which are critical for maintaining component life. The current experimental study dynamically simulated molten particle deposition on a conducting blade endwall with the injection of molten wax. The key nondimensional parameters for modeling of conjugate heat transfer and deposition were replicated in the experiment. The endwall was cooled with internal impingement jet cooling and film cooling. Increasing blowing ratio mitigated some deposition at the film cooling hole exits and in areas of coolest endwall temperatures. After deposition, the external surface temperatures and internal endwall temperatures were measured and found to be warmer than the endwall temperatures measured before deposition. Although the deposition helps insulate the endwall from the mainstream, the roughness effects of the deposition counteract the insulating effect by decreasing the benefit of film cooling and by increasing external heat transfer coefficients.
- 15 June 2015
- Published by ASME International
Overall Effectiveness and Flowfield Measurements for an Endwall With Non-Axisymmetric Contouring
Endwall contouring is a technique used to reduce the strength and development of three-dimensional secondary flows in a turbine vane or blade passage in a gas turbine. The secondary flows locally affect the external heat transfer, particularly on the endwall surface. The combination of external and internal convective heat transfer along with solid conduction determines component temperatures, which affect the service life of turbine components. A conjugate heat transfer model is used to measure the non-dimensional external surface temperature, known as overall effectiveness, of an endwall with non-axisymmetric contouring. The endwall cooling methods include internal impingement cooling and external film cooling. Measured values of overall effectiveness show that endwall contouring reduces the impingement effectiveness alone, but increases the effectiveness of film cooling alone. Given the combined case of both impingement and film cooling, the laterally averaged overall effectiveness is not significantly changed between the flat and contoured endwall. Flowfield measurements indicate that the size and location of the passage vortex changes as film cooling is added and as the blowing ratio increases. Because endwall contouring can produce local effects on internal cooling and film cooling performance, the implications for heat transfer should be considered in endwall contour designs.
- 15 June 2015
- Published by ASME International
Overall Effectiveness and Flowfield Measurements for an Endwall With Non-Axisymmetric Contouring
Endwall contouring is a technique used to reduce the strength and development of three-dimensional secondary flows in a turbine vane or blade passage in a gas turbine. The secondary flows locally affect the external heat transfer, particularly on the endwall surface. The combination of external and internal convective heat transfer along with solid conduction determines component temperatures, which affect the service life of turbine components. A conjugate heat transfer model is used to measure the non-dimensional external surface temperature, known as overall effectiveness, of an endwall with non-axisymmetric contouring. The endwall cooling methods include internal impingement cooling and external film cooling. Measured values of overall effectiveness show that endwall contouring reduces the impingement effectiveness alone, but increases the effectiveness of film cooling alone. Given the combined case of both impingement and film cooling, the laterally averaged overall effectiveness is not significantly changed between the flat and contoured endwall. Flowfield measurements indicate that the size and location of the passage vortex changes as film cooling is added and as the blowing ratio increases. Because endwall contouring can produce local effects on internal cooling and film cooling performance, the implications for heat transfer should be considered in endwall contour designs.