Marina. G. Persova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marina. G. Persova has a total of 120 co-authors. Here are the top co-authors by number of shared publications:
- Yuri G. Soloveichik
Novosibirsk State Technical University
35 shared publications - Denis V. Vagin
Novosibirsk State Technical University, Novosibirsk, Russia
20 shared publications - Yulia I. Koshkina
Novosibirsk State Technical University
15 shared publications Yuri G. Soloveichik
Novosibirsk State Technical University
12 shared publications- Petr A. Domnikov
Novosibirsk State Technical University, Russia
11 shared publications Denis V. Vagin
Novosibirsk State Technical University
9 shared publications
Latest Publications
- Open Access
- 11 October 2026
- Published by Kazan Federal University in Uchenye Zapiski Kazanskogo Universiteta. Seriya Fiziko-Matematicheskie Nauki
- Vol. 168 (3) , 563-585
An approach to solving coupled 3D problems of thermohydrodynamics and electromagnetism in modeling the development of super-viscous oil fields using electromagnetic heating
This article proposes a method for solving coupled 3D problems of non-isothermal multiphase flow and electromagnetic (EM) heating when modeling the development of super-viscous oil (SVO) fields. The approach is based on the finite element method with vector (for EM heating) and scalar (for determining pressure in multiphase flow modeling) basis functions. The temperature field is calculated using mathematical models of fluid and conductive heat transfer. A modified finite difference method is used to model conductive heat transfer. The modeling of the development process is illustrated using a fragment of the hydrodynamic model of SVO fields. The distributions of oil saturation and temperature at different stages of the reservoir development are examined. The SVO production rates under steam-assisted gravity drainage with and without EM heating are compared. The findings suggest that the use of EM heating can increase oil production, and the optimal heating time of the source can be identified from mathematical modeling and depends on the geometry and various physical properties of the reservoir.
- 11 October 2026
- Published by Kazan Federal University in Uchenye Zapiski Kazanskogo Universiteta. Seriya Fiziko-Matematicheskie Nauki
- Vol. 168 (3) , 563-585
Open AccessAn approach to solving coupled 3D problems of thermohydrodynamics and electromagnetism in modeling the development of super-viscous oil fields using electromagnetic heating
This article proposes a method for solving coupled 3D problems of non-isothermal multiphase flow and electromagnetic (EM) heating when modeling the development of super-viscous oil (SVO) fields. The approach is based on the finite element method with vector (for EM heating) and scalar (for determining pressure in multiphase flow modeling) basis functions. The temperature field is calculated using mathematical models of fluid and conductive heat transfer. A modified finite difference method is used to model conductive heat transfer. The modeling of the development process is illustrated using a fragment of the hydrodynamic model of SVO fields. The distributions of oil saturation and temperature at different stages of the reservoir development are examined. The SVO production rates under steam-assisted gravity drainage with and without EM heating are compared. The findings suggest that the use of EM heating can increase oil production, and the optimal heating time of the source can be identified from mathematical modeling and depends on the geometry and various physical properties of the reservoir.
- 27 July 2026
- Published by Elsevier in Computers & Geosciences
- Vol. 216
3D frequency-domain geoelectromagnetic modeling with a primary-secondary field approach
- 27 July 2026
- Published by Elsevier in Computers & Geosciences
- Vol. 216
3D frequency-domain geoelectromagnetic modeling with a primary-secondary field approach
- 1 June 2026
- Published by Allerton Press in Russian Electrical Engineering
- Vol. 97 (6) , 522-527
Numerical Simulation of an Induction Motor with a Frequency-Controlled Drive in Industrial Application for Production of Medicines
The characteristics of an induction motor with a frequency-controlled drive in the conditions of its industrial operation in the manufacture of medicines a
- 1 June 2026
- Published by Allerton Press in Russian Electrical Engineering
- Vol. 97 (6) , 522-527
Numerical Simulation of an Induction Motor with a Frequency-Controlled Drive in Industrial Application for Production of Medicines
The characteristics of an induction motor with a frequency-controlled drive in the conditions of its industrial operation in the manufacture of medicines a
- Open Access
- 30 December 2025
- Published by Georesursy LLC in Georesursy
- Vol. 27 (4) , 276-285
Modeling the Process of Polymer Injection Into the Reservoir Taking Into Account the Shear Rate
The paper is devoted to the analysis of the influence of the shear rate on the results of hydrodynamic modeling in reservoirs when planning and optimizing polymer flooding technologies in oil production problems. Three-dimensional hydrodynamic modeling is performed taking into account that the viscosity of the displacing agent in the reservoir is calculated according to a tabularly specified dependence on the polymer concentration and shear rate. The paper presents the results of computational experiments for polymer flooding for a three-dimensional reservoir model with and without taking into account the shear rate for two types of oil and polymers. Evaluations of the polymer flooding efficiency are given. It is shown that the bottomhole pressure significantly depends on the shear rate. Therefore, failure to take into account the shear rate during planning may lead to incorrect conclusions about possible daily volumes and concentrations of polymer injection, incorrect predictions of bottomhole pressures, and also lead to significant distortions in the assessment of the effectiveness of polymer flooding as a whole.
- 30 December 2025
- Published by Georesursy LLC in Georesursy
- Vol. 27 (4) , 276-285
Open AccessModeling the Process of Polymer Injection Into the Reservoir Taking Into Account the Shear Rate
The paper is devoted to the analysis of the influence of the shear rate on the results of hydrodynamic modeling in reservoirs when planning and optimizing polymer flooding technologies in oil production problems. Three-dimensional hydrodynamic modeling is performed taking into account that the viscosity of the displacing agent in the reservoir is calculated according to a tabularly specified dependence on the polymer concentration and shear rate. The paper presents the results of computational experiments for polymer flooding for a three-dimensional reservoir model with and without taking into account the shear rate for two types of oil and polymers. Evaluations of the polymer flooding efficiency are given. It is shown that the bottomhole pressure significantly depends on the shear rate. Therefore, failure to take into account the shear rate during planning may lead to incorrect conclusions about possible daily volumes and concentrations of polymer injection, incorrect predictions of bottomhole pressures, and also lead to significant distortions in the assessment of the effectiveness of polymer flooding as a whole.
- 31 May 2025
- Published by Springer Nature
- p. 587-598
Increasing the Efficiency of Constructing 3D Oil Reservoir Models to Optimize Further Development
- 31 May 2025
- Published by Springer Nature
- p. 587-598
Increasing the Efficiency of Constructing 3D Oil Reservoir Models to Optimize Further Development
- Open Access
- 1 January 2024
- Published by Saint Petersburg State University in Vestnik of Saint Petersburg University. Earth Sciences
- Vol. 69 (2)
Analysis of the capabilities of marine electrical exploration technologies in solving problems of prospecting and monitoring oil and gas fields using 3D modeling and geometric 3D inversion
The possibilities and comparative analysis of marine electrical exploration technologies for solving problems of hydrocarbon search and monitoring of oil-water contact are presented. The studies were carried out using a 3D modeling and geometric 3D inversion. The 3D modeling method is based on a special mathematical formulation with two-stage primary-secondary field approach and finite element approximation using vector basis functions. The 3D geometric inversion method is aimed at maximizing the accuracy of determining the boundaries of target objects. We consider a new technology for electrical prospecting, which is implemented in start-stop mode and make measurements in the time domain. This technology includes an eight-arm receiver located on the seabed and two sources in the form of horizontal electric dipoles, which can be located either on the seabed or at the surface of the water. It is shown that this technology makes it possible to obtain a significantly larger absolute and relative signal from a deep-lying object of increased resistivity compared to technologies in which the field is excited and received either by horizontal or vertical lines. For technology with an eight-arm receiver, we analyze the error in determining the oil-water contact and equivalence. It is shown that in the case of sufficient sensitivity of signals to the presence of a deep target object, the position of its boundaries can be determined with an accuracy of no worse than 200 m for a target depth of 2.5 km if the contrast in the resistivity of the object to the background medium is sufficient. It is also shown that the position of the oil-saturated zone boundary is determined by the change of sign between negative and positive extrema in the deviations of signals obtained when this boundary is displaced during oil production, and the resistivity of the area remaining after the displacement of the main volume of oil is determined by the level of these extrema. This, in turn, opens up prospects for using this technology in solving problems of monitoring the boundary of the oil-saturated zone during the development of offshore oil fields.
- 1 January 2024
- Published by Saint Petersburg State University in Vestnik of Saint Petersburg University. Earth Sciences
- Vol. 69 (2)
Open AccessAnalysis of the capabilities of marine electrical exploration technologies in solving problems of prospecting and monitoring oil and gas fields using 3D modeling and geometric 3D inversion
The possibilities and comparative analysis of marine electrical exploration technologies for solving problems of hydrocarbon search and monitoring of oil-water contact are presented. The studies were carried out using a 3D modeling and geometric 3D inversion. The 3D modeling method is based on a special mathematical formulation with two-stage primary-secondary field approach and finite element approximation using vector basis functions. The 3D geometric inversion method is aimed at maximizing the accuracy of determining the boundaries of target objects. We consider a new technology for electrical prospecting, which is implemented in start-stop mode and make measurements in the time domain. This technology includes an eight-arm receiver located on the seabed and two sources in the form of horizontal electric dipoles, which can be located either on the seabed or at the surface of the water. It is shown that this technology makes it possible to obtain a significantly larger absolute and relative signal from a deep-lying object of increased resistivity compared to technologies in which the field is excited and received either by horizontal or vertical lines. For technology with an eight-arm receiver, we analyze the error in determining the oil-water contact and equivalence. It is shown that in the case of sufficient sensitivity of signals to the presence of a deep target object, the position of its boundaries can be determined with an accuracy of no worse than 200 m for a target depth of 2.5 km if the contrast in the resistivity of the object to the background medium is sufficient. It is also shown that the position of the oil-saturated zone boundary is determined by the change of sign between negative and positive extrema in the deviations of signals obtained when this boundary is displaced during oil production, and the resistivity of the area remaining after the displacement of the main volume of oil is determined by the level of these extrema. This, in turn, opens up prospects for using this technology in solving problems of monitoring the boundary of the oil-saturated zone during the development of offshore oil fields.
- Open Access
- 22 November 2023
- Published by Saratov State University in Izvestiya of Saratov University. New Series. Series: Mathematics. Mechanics. Informatics
- Vol. 23 (4) , 544-558
Optimization of oil field development based on a 3D reservoir model obtained as a result of history matching
- 22 November 2023
- Published by Saratov State University in Izvestiya of Saratov University. New Series. Series: Mathematics. Mechanics. Informatics
- Vol. 23 (4) , 544-558
Open AccessOptimization of oil field development based on a 3D reservoir model obtained as a result of history matching
- 27 December 2022
- Published by Novosibirsk State Technical University in Analysis and data processing systems
- No. 4
Approach to the determination of the heat transfer coefficient between rock and fluid mixture for modeling non-isothermal multiphase flow
The paper presents an approach to calculation of the coefficient determining the rate of heat transfer between a fluid mixture in oil reservoir and a matrix-rock. This coefficient is necessary for further joint modeling of hydrodynamic and thermal processes that occur in the field reservoir during its development using, for example, thermal methods for enhanced oil recovery. To model the processes of a non-isothermal multiphase flow, an approach based on implicit pressure calculation using the finite element method and explicit calculation of phase saturations is used. The approach to determining the heat transfer coefficient is based on solving the thermal problem in an area corresponding to a channel of a porous medium and a part of the matrix-rock around it. In this case, a fluid mixture with a known temperature value, different from the initial temperature in the channel and matrix-rock, enters the channel at a given rate. A two-dimensional problem is solved in an axisymmetric formulation by the finite element method.Numerical experiments to determine the heat transfer coefficient were carried out on models for various values of the channel size, porosity, initial temperatures of the medium, temperature of the mixture entering the channel, thermal properties of the fluid mixture and rock. As a result of the study, it was found that the channel size and porosity have the most significant effect on the value of the heat transfer coefficient, since these characteristics determine the volume of the matrix-rock, which should “warm up / cool down” when the temperature of the fluid mixture in the channel changes. Also, the coefficient values obtained were quite large, since the heat exchange between the rock and the mixture in the channel occurs in minutes, which practically corresponds to instantaneous heat transfer when it comes to modeling field development processes, where time steps are days and months.
- 27 December 2022
- Published by Novosibirsk State Technical University in Analysis and data processing systems
- No. 4
Approach to the determination of the heat transfer coefficient between rock and fluid mixture for modeling non-isothermal multiphase flow
The paper presents an approach to calculation of the coefficient determining the rate of heat transfer between a fluid mixture in oil reservoir and a matrix-rock. This coefficient is necessary for further joint modeling of hydrodynamic and thermal processes that occur in the field reservoir during its development using, for example, thermal methods for enhanced oil recovery. To model the processes of a non-isothermal multiphase flow, an approach based on implicit pressure calculation using the finite element method and explicit calculation of phase saturations is used. The approach to determining the heat transfer coefficient is based on solving the thermal problem in an area corresponding to a channel of a porous medium and a part of the matrix-rock around it. In this case, a fluid mixture with a known temperature value, different from the initial temperature in the channel and matrix-rock, enters the channel at a given rate. A two-dimensional problem is solved in an axisymmetric formulation by the finite element method.Numerical experiments to determine the heat transfer coefficient were carried out on models for various values of the channel size, porosity, initial temperatures of the medium, temperature of the mixture entering the channel, thermal properties of the fluid mixture and rock. As a result of the study, it was found that the channel size and porosity have the most significant effect on the value of the heat transfer coefficient, since these characteristics determine the volume of the matrix-rock, which should “warm up / cool down” when the temperature of the fluid mixture in the channel changes. Also, the coefficient values obtained were quite large, since the heat exchange between the rock and the mixture in the channel occurs in minutes, which practically corresponds to instantaneous heat transfer when it comes to modeling field development processes, where time steps are days and months.
- 4 October 2022
- Published by Elsevier in Computers & Geosciences
- Vol. 169
Iterative solver with folded preconditioner for finite element simulation of magnetotelluric fields
- 4 October 2022
- Published by Elsevier in Computers & Geosciences
- Vol. 169
Iterative solver with folded preconditioner for finite element simulation of magnetotelluric fields