Maria Margareth da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maria Margareth da Silva has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Cristiane Aparecida Martins
Instituto Tecnológico de Aeronáutica
3 shared publications Emily Henriques Quadros Viana Costa
3 shared publicationsFrederick Del Gaudio Campbell
3 shared publications- Karla Donato Fook
Instituto Tecnológico de Aeronáutica
3 shared publications - Ana Claudia Costa de Oliveira
Universidade Federal de Lavras
2 shared publications - Danieli Aparecida Pereira Reis
Universidade Federal de Sao Paulo, Brasil
2 shared publications
Latest Publications
- Open Access
- 23 April 2026
- Published by UNIVAP Universidade de Vale do Paraiba in Revista Univap
- Vol. 32 (73)
APPLICATION AND ANALYSIS OF MICRO-CLADDING PARAMETERS FOR H13 POWDER UNDER 4340 AISI USING A FIBRE TOP-HAT LASER
Generally, the laser micro-cladding is obtained by materials depositing under interest substrates. The technique consists of coat-powder directing into laser beam's focal region; under a substrate surface; promoting metallurgical bonding between the materials. The system therefore has a wide range of applications in engineering. However, it is still little covered in the literature; especially regarding its boundary conditions. With this in mind, this paper aimed the application and analysis of micro-cladding parameters; from previous studies. To this end, was taken a methodological-route composed by: irradiation starting-parameters. Next, with a deposition of: one-track lines; coat-areas and micro-additive metallurgical manufacturing structures. Using a H13 tool steel as coat-powder, under discoidal substrates 25X5mm of AISI 4340. With an experimental set-up consisted by an Ytterbium fibre laser, transported by a robotic arm and a powder aspersing system. With this, were obtained optimum parameters of laser's power of 1300W and velocity of scanning of 11mm/s. The final results produced structures with well-densification and superior Vickers microhardness; with metallurgical bonding occurrence.
- 23 April 2026
- Published by UNIVAP Universidade de Vale do Paraiba in Revista Univap
- Vol. 32 (73)
Open AccessAPPLICATION AND ANALYSIS OF MICRO-CLADDING PARAMETERS FOR H13 POWDER UNDER 4340 AISI USING A FIBRE TOP-HAT LASER
Generally, the laser micro-cladding is obtained by materials depositing under interest substrates. The technique consists of coat-powder directing into laser beam's focal region; under a substrate surface; promoting metallurgical bonding between the materials. The system therefore has a wide range of applications in engineering. However, it is still little covered in the literature; especially regarding its boundary conditions. With this in mind, this paper aimed the application and analysis of micro-cladding parameters; from previous studies. To this end, was taken a methodological-route composed by: irradiation starting-parameters. Next, with a deposition of: one-track lines; coat-areas and micro-additive metallurgical manufacturing structures. Using a H13 tool steel as coat-powder, under discoidal substrates 25X5mm of AISI 4340. With an experimental set-up consisted by an Ytterbium fibre laser, transported by a robotic arm and a powder aspersing system. With this, were obtained optimum parameters of laser's power of 1300W and velocity of scanning of 11mm/s. The final results produced structures with well-densification and superior Vickers microhardness; with metallurgical bonding occurrence.
- Open Access
- 5 February 2026
- Published by Elsevier in SSRN Electronic Journal
Surface mechanical properties and thermal diffusivity of plasma nitrided Hastelloy X
The growing need to utilize superalloys in challenging environments is driving ongoing advancements in effective coating systems. Within this framework, plasma nitriding can be evaluated as either a standalone solution or integrated with other methods. Applied to nickel-based Hastelloy X alloy, this surface processing represents an original aspect of the research, providing comprehensive analysis through compositional (via EDS), structural (XRD and micro-Raman), and microstructural (SEM) characterizations of both the surface and bulk material. Nitrogen diffusion and retention in the lattice compete with chromium depletion, resulting in various layer thicknesses (6.5 μm to 3.2 μm) and structures depending on the treatment temperatures: mainly expanded austenite γN at 400 °C; nitride phases (notably CrN, Cr2N) atop γN at 600 °C; and predominantly nitrides at 700 °C. Heat-induced carbide precipitation in the bulk has a limited impact on mechanical properties. Accordingly, the hardness-to-elastic modulus ratio ([[EQUATION]]), measured by nanoindentation, increases by a factor of 5.1 at the 400 ºC condition and 2.8 in the 700 ºC one. The unique features of the nitrided layers notably influence the material´s thermal diffusivity, determined by using the rear photoacoustic signal technique (sensitive to micrometer-scale layer contributions), achieving up to a 2.4-fold enhancement at 700 ºC. These findings indicate that plasma nitriding enables the tailoring of mechanically resistant surfaces with distinctive thermal properties on Hatelloy X.
- 5 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSurface mechanical properties and thermal diffusivity of plasma nitrided Hastelloy X
The growing need to utilize superalloys in challenging environments is driving ongoing advancements in effective coating systems. Within this framework, plasma nitriding can be evaluated as either a standalone solution or integrated with other methods. Applied to nickel-based Hastelloy X alloy, this surface processing represents an original aspect of the research, providing comprehensive analysis through compositional (via EDS), structural (XRD and micro-Raman), and microstructural (SEM) characterizations of both the surface and bulk material. Nitrogen diffusion and retention in the lattice compete with chromium depletion, resulting in various layer thicknesses (6.5 μm to 3.2 μm) and structures depending on the treatment temperatures: mainly expanded austenite γN at 400 °C; nitride phases (notably CrN, Cr2N) atop γN at 600 °C; and predominantly nitrides at 700 °C. Heat-induced carbide precipitation in the bulk has a limited impact on mechanical properties. Accordingly, the hardness-to-elastic modulus ratio ([[EQUATION]]), measured by nanoindentation, increases by a factor of 5.1 at the 400 ºC condition and 2.8 in the 700 ºC one. The unique features of the nitrided layers notably influence the material´s thermal diffusivity, determined by using the rear photoacoustic signal technique (sensitive to micrometer-scale layer contributions), achieving up to a 2.4-fold enhancement at 700 ºC. These findings indicate that plasma nitriding enables the tailoring of mechanically resistant surfaces with distinctive thermal properties on Hatelloy X.
- 1 June 2025
- Published by IATED Academy in EDULEARN Proceedings
- Vol. 1, 1016-1023
BRINGING EDUCATION ANYWHERE: A MOBILE LAB INITIATIVE
- 1 June 2025
- Published by IATED Academy in EDULEARN Proceedings
- Vol. 1, 1016-1023
BRINGING EDUCATION ANYWHERE: A MOBILE LAB INITIATIVE
- 1 June 2025
- Published by IATED Academy in EDULEARN Proceedings
- Vol. 1, 1033-1040
CO-AUTHORED PROJECTS IN EDUCATION: A CASE STUDY OF A MOBILE LAB WORKSHOP
- 1 June 2025
- Published by IATED Academy in EDULEARN Proceedings
- Vol. 1, 1033-1040
CO-AUTHORED PROJECTS IN EDUCATION: A CASE STUDY OF A MOBILE LAB WORKSHOP
- Open Access
- 25 April 2025
- Published by UNIVAP Universidade de Vale do Paraiba in Revista Univap
- Vol. 31 (71)
STRUCTURAL CHARACTERIZATION OF WELDED AL6060-T5 ALLOY JOINTS BY FRICTION STIR SPOT WELDING UNDER CORROSION ATACK
Al6060-T5 alloys are widely used in the aerospace, shipbuilding and automotive industries. Nevertheless, the conventional welding process could be weakening its resistance to corrosion. Thus, Friction Stir Spot Welding (FSSW) becomes an alternative to reduce the thermally affected zone (HAZ) at the joints. Although, persist a lack of studies, on current literature, about these welding properties; as welds its corrosion resistance. With this in mind, this present paper evaluated an Al6060-T5 alloy plates welds after periods of 336, 672 and 1008 hours into 3.5% NaCl electrolyte immersion. Where, for each period, the plates were evaluated in terms of open circuit potentials (OCP), micro hardness Vickers, elemental composition and its corrosion severity. The results shown a percentage increasing of oxygen rate (3 to 4%); identifying corrosive activity in the mixing zone. Likewise, electrochemical tests shown a greater susceptibility to corrosion at weld nearing centre regions; due to Mg and Si precipitates presence. Even so, all immersion times samples presented a mild corrosive severity
- 25 April 2025
- Published by UNIVAP Universidade de Vale do Paraiba in Revista Univap
- Vol. 31 (71)
Open AccessSTRUCTURAL CHARACTERIZATION OF WELDED AL6060-T5 ALLOY JOINTS BY FRICTION STIR SPOT WELDING UNDER CORROSION ATACK
Al6060-T5 alloys are widely used in the aerospace, shipbuilding and automotive industries. Nevertheless, the conventional welding process could be weakening its resistance to corrosion. Thus, Friction Stir Spot Welding (FSSW) becomes an alternative to reduce the thermally affected zone (HAZ) at the joints. Although, persist a lack of studies, on current literature, about these welding properties; as welds its corrosion resistance. With this in mind, this present paper evaluated an Al6060-T5 alloy plates welds after periods of 336, 672 and 1008 hours into 3.5% NaCl electrolyte immersion. Where, for each period, the plates were evaluated in terms of open circuit potentials (OCP), micro hardness Vickers, elemental composition and its corrosion severity. The results shown a percentage increasing of oxygen rate (3 to 4%); identifying corrosive activity in the mixing zone. Likewise, electrochemical tests shown a greater susceptibility to corrosion at weld nearing centre regions; due to Mg and Si precipitates presence. Even so, all immersion times samples presented a mild corrosive severity
- 1 November 2024
- Published by IATED Academy
- Vol. 1, 7039-7046
A COMPUTER PROGRAMMING COURSE IN STEAM FOCUSED ON GAMES DEVELOPMENT
- 1 November 2024
- Published by IATED Academy
- Vol. 1, 7039-7046
A COMPUTER PROGRAMMING COURSE IN STEAM FOCUSED ON GAMES DEVELOPMENT
- 23 February 2023
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 11 (1) , 014007
Effect of plasma immersion ion implantation on wear behavior of Ti-6Al-4V alloy
Ti-6Al-4V alloy is ideal for use in the aeronautical and aerospace industries because of its excellent strength/weight ratio and corrosion resistance. However, its applications at high temperatures are vulnerable due to its high affinity for interstitial elements, such as nitrogen and oxygen. The plasma immersion ion implantation (PIII) technique, performed at high temperature, allows formation of modified layers that can improve the mechanical and tribological properties without compromising the corrosion resistance, which is a characteristic of this alloy. In this work, the samples were treated by PIII at three different temperatures (700, 800, and 900 °C) for 120 min of exposure to evaluate PIII on the mechanical behavior of Ti-6Al-4V alloy compared to data already available in the literature. The aim of this process is to improve surface mechanical properties of the Ti-6Al-4V alloy. The techniques used in this work were x-ray diffraction microhardness, glow discharge optical emission spectrometer, and wear testing in a ball-on-disk tribometer. The results indicate a significantly increased material resistance, with a reduced wear for all treated samples and a reduced friction coefficient for samples treated at 800 and 900 °C. The best results were for alloy treated at 800 and 900 °C, because they maintain the low coefficient throughout the test, which indicates better wear resistance.
- 23 February 2023
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 11 (1) , 014007
Effect of plasma immersion ion implantation on wear behavior of Ti-6Al-4V alloy
Ti-6Al-4V alloy is ideal for use in the aeronautical and aerospace industries because of its excellent strength/weight ratio and corrosion resistance. However, its applications at high temperatures are vulnerable due to its high affinity for interstitial elements, such as nitrogen and oxygen. The plasma immersion ion implantation (PIII) technique, performed at high temperature, allows formation of modified layers that can improve the mechanical and tribological properties without compromising the corrosion resistance, which is a characteristic of this alloy. In this work, the samples were treated by PIII at three different temperatures (700, 800, and 900 °C) for 120 min of exposure to evaluate PIII on the mechanical behavior of Ti-6Al-4V alloy compared to data already available in the literature. The aim of this process is to improve surface mechanical properties of the Ti-6Al-4V alloy. The techniques used in this work were x-ray diffraction microhardness, glow discharge optical emission spectrometer, and wear testing in a ball-on-disk tribometer. The results indicate a significantly increased material resistance, with a reduced wear for all treated samples and a reduced friction coefficient for samples treated at 800 and 900 °C. The best results were for alloy treated at 800 and 900 °C, because they maintain the low coefficient throughout the test, which indicates better wear resistance.
- 11 January 2022
- Published by Springer Nature in International Journal of Fracture
- Vol. 234 (1-2) , 159-175
Behavior of constitutive models from slow strain rate test of maraging 300 and 350 steels performed in several environmental conditions
- 11 January 2022
- Published by Springer Nature in International Journal of Fracture
- Vol. 234 (1-2) , 159-175
Behavior of constitutive models from slow strain rate test of maraging 300 and 350 steels performed in several environmental conditions
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (3)
Modeling and Numerical Validation of Stress-Strain Curves of Maraging Steels, Grades 300 and 350 Under Hydrogen Embrittlement
Maraging steels are ferrous alloys with Ni, Co, Mo, and Ti additions. These materials are a special class of ultra high mechanical strength steels with wide and special applications in strategic areas, which makes their knowledge very valuable. Computational advances allowed to analyze the behavior of these materials numerically, using the finite element method and developing mathematical models that can represent numerically its mechanical behavior. The present work has the objective of surveying the mechanical properties of maraging steels 300 and 350 by slow strain rate tensile (SSRT) tests, after the solution treatment at 1183K for 1h. Additionally, it was evaluated the hydrogen embrittlement in samples tested by SSRT under cathodic protection with a potential -1.2 VSCE in 3.5% NaCl solution. The study was complemented with detailed fractographic analysis. This work also presents the analysis of representative models by use of Hollomon, Swift, Voce and coupled Swift-Voce equations to describe the strain-hardening behavior. Compared to the others, the Voce’s model was the one which best fitted the experimental results, with values of R2 higher than 0.992. Through the variation of the chemical composition found in the different grades of maraging steels, this work contemplates the creation of a generalized Voce model based on the variation of the Ti content. The work concludes presenting the generalized Voce model proposed and a numerical analysis of the SSRT results with a good accuracy of the strain-hardening response.
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (3)
Open AccessModeling and Numerical Validation of Stress-Strain Curves of Maraging Steels, Grades 300 and 350 Under Hydrogen Embrittlement
Maraging steels are ferrous alloys with Ni, Co, Mo, and Ti additions. These materials are a special class of ultra high mechanical strength steels with wide and special applications in strategic areas, which makes their knowledge very valuable. Computational advances allowed to analyze the behavior of these materials numerically, using the finite element method and developing mathematical models that can represent numerically its mechanical behavior. The present work has the objective of surveying the mechanical properties of maraging steels 300 and 350 by slow strain rate tensile (SSRT) tests, after the solution treatment at 1183K for 1h. Additionally, it was evaluated the hydrogen embrittlement in samples tested by SSRT under cathodic protection with a potential -1.2 VSCE in 3.5% NaCl solution. The study was complemented with detailed fractographic analysis. This work also presents the analysis of representative models by use of Hollomon, Swift, Voce and coupled Swift-Voce equations to describe the strain-hardening behavior. Compared to the others, the Voce’s model was the one which best fitted the experimental results, with values of R2 higher than 0.992. Through the variation of the chemical composition found in the different grades of maraging steels, this work contemplates the creation of a generalized Voce model based on the variation of the Ti content. The work concludes presenting the generalized Voce model proposed and a numerical analysis of the SSRT results with a good accuracy of the strain-hardening response.
- Open Access
Fiber Laser Surface Melting of a NiTi Superelastic Alloy: Influence on Structural and Mechanical Properties
The surface melting of a NiTi superelastic alloy using a high-power laser Yb:Fiber was investigated. The influence of this process on the microstructural and mechanical properties was also examined. The reference material was a 3 mm nitinol strip with a homogeneous austenitic B2 phase. For the laser surface melting process, input fluences were applied from 17.5 to 45 J/mm2. The morphology of the structure and the chemical composition of several regions were determined by optical microscopy, scanning electron microscopy, dispersive energy spectra, and X-ray diffraction techniques. The mechanical properties, such as modulus of elasticity and hardness, were determined using nanoindentation and microindentation techniques. The greatest surface finishing of the fusion zone was observed for the condition 35 J/mm2. Three well-defined regions (fusion zone (FZ), heat-affected zone (HAZ), base metal (BM)) could be observed and dimensions of grain size, width, and depth of the melted pool were directly affected by the laser fluence. The geometry of the molten pool could be controlled by the optimization of the laser parameters. High laser fluence caused preferential volatilization of nickel, dynamic precipitation of intermetallic phases, including Ti2Ni, Ni3Ti, and Ni4Ti3, as well as solubilization of TiC in the matrix, which led to grain refinement. Thus, high laser fluence is a suitable technique to enhance mechanical properties such as hardness and Young’s modulus.
Open AccessFiber Laser Surface Melting of a NiTi Superelastic Alloy: Influence on Structural and Mechanical Properties
The surface melting of a NiTi superelastic alloy using a high-power laser Yb:Fiber was investigated. The influence of this process on the microstructural and mechanical properties was also examined. The reference material was a 3 mm nitinol strip with a homogeneous austenitic B2 phase. For the laser surface melting process, input fluences were applied from 17.5 to 45 J/mm2. The morphology of the structure and the chemical composition of several regions were determined by optical microscopy, scanning electron microscopy, dispersive energy spectra, and X-ray diffraction techniques. The mechanical properties, such as modulus of elasticity and hardness, were determined using nanoindentation and microindentation techniques. The greatest surface finishing of the fusion zone was observed for the condition 35 J/mm2. Three well-defined regions (fusion zone (FZ), heat-affected zone (HAZ), base metal (BM)) could be observed and dimensions of grain size, width, and depth of the melted pool were directly affected by the laser fluence. The geometry of the molten pool could be controlled by the optimization of the laser parameters. High laser fluence caused preferential volatilization of nickel, dynamic precipitation of intermetallic phases, including Ti2Ni, Ni3Ti, and Ni4Ti3, as well as solubilization of TiC in the matrix, which led to grain refinement. Thus, high laser fluence is a suitable technique to enhance mechanical properties such as hardness and Young’s modulus.