Ilia G. Dyakov
Research Subjects
Ilia G. Dyakov has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Sergei A. Kusmanov
Moscow State University of Technology “STANKIN”, Moscow, Russia
12 shared publications P. N. Belkin
Kostroma State University
5 shared publications- I. V. Tambovskiy
Department of Mathematical and Natural Sciences, Kostroma State University, 156005 Kostroma, Russia
4 shared publications - Sergeiy A. Silkin
Kostroma State University, Kostroma, Russia
4 shared publications P.N. Belkin
3 shared publications- Igor Suminov
Department of High-Efficiency Machining Technologies, Moscow State University of Technology “STANKIN”, 127994 Moscow, Russia
2 shared publications
Latest Publications
- Open Access
Features of Cathodic Plasma Electrolytic Nitrocarburizing of Low-Carbon Steel in an Aqueous Electrolyte of Ammonium Nitrate and Glycerin
The possibility of using an aqueous non-toxic electrolyte of ammonium nitrate and glycerin for the cathodic plasma electrolytic nitrocarburizing of low-carbon steel is considered in this paper. Surface morphology and roughness, element and phase compositions, and microhardness of the modified layer were investigated. Kinetic calculations of the processes of nitrogen and carbon diffusion into the steel surface are proposed, taking into account their mutual influence. Wear resistance was studied under dry friction conditions with tool alloy steel as a counter-body. Corrosion studies are performed using potentiodynamic polarization curves in 3.5% sodium chloride solution. The plasma electrolytic nitrocarburizing in an aqueous electrolyte with ammonium nitrate and glycerin is established to increase surface hardness up to 980 HV due to the formation of a nitrocarburized layer with 1.35 ± 0.12% carbon and 0.32 ± 0.08% nitrogen concentration. The influence of erosion in electrolyte plasma and high-temperature oxidation on the morphology and surface roughness is shown. The presence of a dense oxide layer, low surface roughness, and high hardness of the diffusion layer favor a decrease in the friction coefficient by 1.3 times, weight wear by 1.8 times and corrosion current density by 1.4 times.
Open AccessFeatures of Cathodic Plasma Electrolytic Nitrocarburizing of Low-Carbon Steel in an Aqueous Electrolyte of Ammonium Nitrate and Glycerin
The possibility of using an aqueous non-toxic electrolyte of ammonium nitrate and glycerin for the cathodic plasma electrolytic nitrocarburizing of low-carbon steel is considered in this paper. Surface morphology and roughness, element and phase compositions, and microhardness of the modified layer were investigated. Kinetic calculations of the processes of nitrogen and carbon diffusion into the steel surface are proposed, taking into account their mutual influence. Wear resistance was studied under dry friction conditions with tool alloy steel as a counter-body. Corrosion studies are performed using potentiodynamic polarization curves in 3.5% sodium chloride solution. The plasma electrolytic nitrocarburizing in an aqueous electrolyte with ammonium nitrate and glycerin is established to increase surface hardness up to 980 HV due to the formation of a nitrocarburized layer with 1.35 ± 0.12% carbon and 0.32 ± 0.08% nitrogen concentration. The influence of erosion in electrolyte plasma and high-temperature oxidation on the morphology and surface roughness is shown. The presence of a dense oxide layer, low surface roughness, and high hardness of the diffusion layer favor a decrease in the friction coefficient by 1.3 times, weight wear by 1.8 times and corrosion current density by 1.4 times.
- Open Access
Enhancement of Medium-Carbon Steel Corrosion and Wear Resistance by Plasma Electrolytic Nitriding and Polishing
The influence of technological parameters of plasma electrolytic nitriding and polishing on the wear resistance and corrosion resistance of medium-carbon steel is considered. The morphology and roughness of the surface, phase composition and microhardness of the modified layer have been investigated. Wear resistance was studied under dry friction conditions with bearing steel as counter-body. It was found that plasma electrolytic polishing removes the loose part of the oxide layer and provides a two-fold decrease in surface roughness compared with untreated steel, and 2.8 times compared with the nitrided one. Combined processing at optimal technological parameters leads to an increase in microhardness up to 1130 HV, an increase in wear resistance by 70 times, and a decrease in the corrosion current density by almost 3 times in comparison with untreated steel.
Open AccessEnhancement of Medium-Carbon Steel Corrosion and Wear Resistance by Plasma Electrolytic Nitriding and Polishing
The influence of technological parameters of plasma electrolytic nitriding and polishing on the wear resistance and corrosion resistance of medium-carbon steel is considered. The morphology and roughness of the surface, phase composition and microhardness of the modified layer have been investigated. Wear resistance was studied under dry friction conditions with bearing steel as counter-body. It was found that plasma electrolytic polishing removes the loose part of the oxide layer and provides a two-fold decrease in surface roughness compared with untreated steel, and 2.8 times compared with the nitrided one. Combined processing at optimal technological parameters leads to an increase in microhardness up to 1130 HV, an increase in wear resistance by 70 times, and a decrease in the corrosion current density by almost 3 times in comparison with untreated steel.
- 18 September 2019
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 28 (9) , 5425-5432
Enhancement of Wear and Corrosion Resistance in Medium Carbon Steel by Plasma Electrolytic Nitriding and Polishing
- 18 September 2019
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 28 (9) , 5425-5432
Enhancement of Wear and Corrosion Resistance in Medium Carbon Steel by Plasma Electrolytic Nitriding and Polishing
- 1 March 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 362, 124-131
Increasing wear and corrosion resistance of tool steel by anodic plasma electrolytic nitriding
- 1 March 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 362, 124-131
Increasing wear and corrosion resistance of tool steel by anodic plasma electrolytic nitriding
- 10 April 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (5) , 2404-2410
Increasing Wear Resistance of Titanium Alloys by Anode Plasma Electrolytic Saturation with Interstitial Elements
- 10 April 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (5) , 2404-2410
Increasing Wear Resistance of Titanium Alloys by Anode Plasma Electrolytic Saturation with Interstitial Elements
- 1 March 2017
- Published by Ivanovo State University of Chemistry and Technology in ChemChemTech
- Vol. 60 (1) , 81-86
IMPROVEMENT OF CORROSION AND WEAR RESISTANCE OF 45 STEEL WITH ANODE PLASMA ELECTROLYTE NITRIDING
For citation:Smirnov A.A., Silkin S.A., Belkin P.N., Dyakov I.G., Sevostyanova V.S., Kusmanov S.A. Improvement of corrosion and wear resistance of 45 steel with anode plasma electrolyte nitriding. Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol. 2017. V. 60. N 1. P. 81-86.The wear and corrosion resistance was studied after anode plasma electrolytic nitriding (PEN) the carbon steel in electrolyte containing ammonium chloride and ammonia or ammonium nitrate. Tribological properties of nitrided samples were evaluated using a pin-on-disk and ball-on-disk tribometers under lubricated testing conditions and dry sliding. The effect of processing temperature on corrosion resistance of the PEN samples was examined by means of potentiodynamic polarization in a solution of sodium sulfate (0.1 N). The anode PEN at 750 °C during 5 min in electrolyte containing ammonium chloride (15%) and ammonium nitrate (5%) results in a decrease in a corrosion current density by a factor of 16. The anode PEN at 750 °C during 10 min in electrolyte containing ammonium chloride (10%) and ammonia (5%) results in the decrease in a corrosion current density by a factor of 6. Improving the corrosion resistance of steel takes place due to the formation of the surface oxide layer and the nitride-martensite zone. Results of wear tests under lubricated testing conditions with the speed of 0.49 m/s and load of 208.6 N against hardened steel (50 HRC) diskshow that friction coefficient of nitrided samples decreases at all PEN temperatures. The anode PEN at 750 °C during 10 min in electrolyte containing ammonium chloride and ammonia results in the decrease in wear rate more than 9 times and friction coefficient from 0.17 to 0.12. Nitriding in electrolyte with ammonium chloride and nitrate also results in minimum of the wear rate after the PEN at 750 °C during 10 min but it gives lesser result due to the lower hardness of the nitride-martensite sublayer. Wear tests during dry sliding with the speed of 0.2 m/s and load of 5 N against bearing steel ballshow that friction coefficient of nitrided samples decreases from 0.41 to 0.28. The increasing the load reduces the friction coefficient that means saving mode of elastic contact and a good running-in ability of oxide layer in the studied range. Linear wear decreases from 35 to 21 mm at load of 10 N and sliding speed of 0.4 m/s.
- 1 March 2017
- Published by Ivanovo State University of Chemistry and Technology in ChemChemTech
- Vol. 60 (1) , 81-86
IMPROVEMENT OF CORROSION AND WEAR RESISTANCE OF 45 STEEL WITH ANODE PLASMA ELECTROLYTE NITRIDING
For citation:Smirnov A.A., Silkin S.A., Belkin P.N., Dyakov I.G., Sevostyanova V.S., Kusmanov S.A. Improvement of corrosion and wear resistance of 45 steel with anode plasma electrolyte nitriding. Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol. 2017. V. 60. N 1. P. 81-86.The wear and corrosion resistance was studied after anode plasma electrolytic nitriding (PEN) the carbon steel in electrolyte containing ammonium chloride and ammonia or ammonium nitrate. Tribological properties of nitrided samples were evaluated using a pin-on-disk and ball-on-disk tribometers under lubricated testing conditions and dry sliding. The effect of processing temperature on corrosion resistance of the PEN samples was examined by means of potentiodynamic polarization in a solution of sodium sulfate (0.1 N). The anode PEN at 750 °C during 5 min in electrolyte containing ammonium chloride (15%) and ammonium nitrate (5%) results in a decrease in a corrosion current density by a factor of 16. The anode PEN at 750 °C during 10 min in electrolyte containing ammonium chloride (10%) and ammonia (5%) results in the decrease in a corrosion current density by a factor of 6. Improving the corrosion resistance of steel takes place due to the formation of the surface oxide layer and the nitride-martensite zone. Results of wear tests under lubricated testing conditions with the speed of 0.49 m/s and load of 208.6 N against hardened steel (50 HRC) diskshow that friction coefficient of nitrided samples decreases at all PEN temperatures. The anode PEN at 750 °C during 10 min in electrolyte containing ammonium chloride and ammonia results in the decrease in wear rate more than 9 times and friction coefficient from 0.17 to 0.12. Nitriding in electrolyte with ammonium chloride and nitrate also results in minimum of the wear rate after the PEN at 750 °C during 10 min but it gives lesser result due to the lower hardness of the nitride-martensite sublayer. Wear tests during dry sliding with the speed of 0.2 m/s and load of 5 N against bearing steel ballshow that friction coefficient of nitrided samples decreases from 0.41 to 0.28. The increasing the load reduces the friction coefficient that means saving mode of elastic contact and a good running-in ability of oxide layer in the studied range. Linear wear decreases from 35 to 21 mm at load of 10 N and sliding speed of 0.4 m/s.
- 1 January 2017
- Published by Allerton Press in Surface Engineering and Applied Electrochemistry
- Vol. 53 (1) , 1-6
Plasma electrolytic treatment of VT22 titanium alloy in electrolytes with carbon-containing compounds
The study investigates the influence of electrolyte compositions containing acetone, glycerol, sucrose, ethylene glycol and ammonium chloride on the properties of VT22 titanium alloy in the process of the anode plasma electrolytic treatment (PET). An X-ray diffractometer and a scanning electron microscopy (SEM) were used to characterize the phase composition and morphology of the modified surface. Tribological properties of the treated titanium alloy were evaluated using a pin-on-disc tribometer under lubricated testing conditions. The effect of electrolyte compositions on the corrosion resistance of the PET samples was examined by means of potentiodynamic polarization in a solution of Na2SO4. It was assumed that the PET provides the saturation of titanium alloy with oxygen and carbon and formation TiO2 with a rutile structure and carbon solid solution in titanium. The anode PET in an electrolyte with glycerol results in an increase in microhardness to 540 HV and a decrease in the corrosion current density by 2.4 times. The friction coefficient of the treated samples in anelectrolyte with sucrose can be reduced 7.5 times. The anode PET in all electrolytes enables todiminish the wear rate of the titanium alloy samples by 3 orders of magnitude and the surface roughness, too, due to the anode dissolution of titanium.
- 1 January 2017
- Published by Allerton Press in Surface Engineering and Applied Electrochemistry
- Vol. 53 (1) , 1-6
Plasma electrolytic treatment of VT22 titanium alloy in electrolytes with carbon-containing compounds
The study investigates the influence of electrolyte compositions containing acetone, glycerol, sucrose, ethylene glycol and ammonium chloride on the properties of VT22 titanium alloy in the process of the anode plasma electrolytic treatment (PET). An X-ray diffractometer and a scanning electron microscopy (SEM) were used to characterize the phase composition and morphology of the modified surface. Tribological properties of the treated titanium alloy were evaluated using a pin-on-disc tribometer under lubricated testing conditions. The effect of electrolyte compositions on the corrosion resistance of the PET samples was examined by means of potentiodynamic polarization in a solution of Na2SO4. It was assumed that the PET provides the saturation of titanium alloy with oxygen and carbon and formation TiO2 with a rutile structure and carbon solid solution in titanium. The anode PET in an electrolyte with glycerol results in an increase in microhardness to 540 HV and a decrease in the corrosion current density by 2.4 times. The friction coefficient of the treated samples in anelectrolyte with sucrose can be reduced 7.5 times. The anode PET in all electrolytes enables todiminish the wear rate of the titanium alloy samples by 3 orders of magnitude and the surface roughness, too, due to the anode dissolution of titanium.
- 1 December 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 307, 1303-1309
Anode plasma electrolytic carburizing of commercial pure titanium
- 1 December 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 307, 1303-1309
Anode plasma electrolytic carburizing of commercial pure titanium
- 11 June 2016
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 36 (5) , 1271-1286
Surface Modification of Low-Carbon Steels by Plasma Electrolytic Nitrocarburising
- 11 June 2016
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 36 (5) , 1271-1286
Surface Modification of Low-Carbon Steels by Plasma Electrolytic Nitrocarburising