Sumit Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sumit Sharma has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Digambar Singh
Malaviya National Institute of Technology Jaipur
9 shared publications Dilip Sharma
Department of Mechanical Engineering Malaviya National Institute of Technology Jaipur India
7 shared publications- Amit Jhalani
Department of Mechanical Engineering, Malaviya National Institute of Technology Jaipur, Jaipur, India
5 shared publications Shyam Lal Soni
Department of Mechanical Engineering Malaviya National Institute of Technology Jaipur India
5 shared publications- Dilip Sharma
Malaviya National Institute of Technology Jaipur
3 shared publications Pushpendra Kumar Sharma
3 shared publications
Latest Publications
- 2 December 2021
- Published by Inderscience Publishers in International Journal of Environment and Sustainable Development
- Vol. 21 (1/2) , 76-96
A review on production processes, performance and emissions analysis of hydrogen as a fuel in I.C. engines
The energy demand increases continuously with rapid increase in the world's population. Continuous depletion of limited non conventional energy resources forces the move towards alternate energy solution. Hydrogen is the environment-friendly and most promising source to meet future energy demand. Non-toxic, non-metallic and high energy content make the hydrogen as a future generation fuel. The main sources of hydrogen production are hydro, biomass, nuclear, wind, geothermal, and solar. Hydrogen can be produced from different methods like thermal, biological, electrical, and photonic. This review article provides detailed information about the production processes of hydrogen, and performance and emissions analysis of hydrogen when it is used as a fuel in internal combustion engines. Brake thermal efficiency of the engine increases with the increase of hydrogen energy share at high and moderate loads. However, at low loads, the efficiency decreases. Carbon-based emissions (HC, CO and CO
- 2 December 2021
- Published by Inderscience Publishers in International Journal of Environment and Sustainable Development
- Vol. 21 (1/2) , 76-96
A review on production processes, performance and emissions analysis of hydrogen as a fuel in I.C. engines
The energy demand increases continuously with rapid increase in the world's population. Continuous depletion of limited non conventional energy resources forces the move towards alternate energy solution. Hydrogen is the environment-friendly and most promising source to meet future energy demand. Non-toxic, non-metallic and high energy content make the hydrogen as a future generation fuel. The main sources of hydrogen production are hydro, biomass, nuclear, wind, geothermal, and solar. Hydrogen can be produced from different methods like thermal, biological, electrical, and photonic. This review article provides detailed information about the production processes of hydrogen, and performance and emissions analysis of hydrogen when it is used as a fuel in internal combustion engines. Brake thermal efficiency of the engine increases with the increase of hydrogen energy share at high and moderate loads. However, at low loads, the efficiency decreases. Carbon-based emissions (HC, CO and CO
- 27 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Impact assessment of acetylene fueling on the performance, emissions, and combustion of a spark-ignition engine
Along with industrialization and transportation, the higher living standard is also the main reason for the increase in energy demand. This increasing energy demand motivates researchers to find new alternative fuels that are eco-friendly and sustainable. In this concern, to analyze the performance, emissions, and combustion characteristics of an SI engine fueled by petrol-acetylene under DF mode is the main purpose of this study. For this purpose, a VCR spark ignition engine was used and operated at the engine maximum speed (1800 rpm). The experimental study was carried out at different acetylene gas flow rates and spark timing. In this study, the acetylene gas flow rate was first optimized on a performance basis. Furthermore, the engine was run at an optimized acetylene gas flow rate (100 LPH) to find out the optimum value of spark timing. In further experimentation, it is also found that the BThE to be maximum and emissions were significantly low or comparable at spark timing 20º CA bTDC (at 100 LPH) as compared to other spark timing and baseline case at all loads. The effects of NOx and smoke are not considerable. Hence, it is not covered in this study. The heat release rate and peak cylinder pressure are found to increase with the advancement of spark timing. But knocking was observed at higher spark advance.
- 27 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Impact assessment of acetylene fueling on the performance, emissions, and combustion of a spark-ignition engine
Along with industrialization and transportation, the higher living standard is also the main reason for the increase in energy demand. This increasing energy demand motivates researchers to find new alternative fuels that are eco-friendly and sustainable. In this concern, to analyze the performance, emissions, and combustion characteristics of an SI engine fueled by petrol-acetylene under DF mode is the main purpose of this study. For this purpose, a VCR spark ignition engine was used and operated at the engine maximum speed (1800 rpm). The experimental study was carried out at different acetylene gas flow rates and spark timing. In this study, the acetylene gas flow rate was first optimized on a performance basis. Furthermore, the engine was run at an optimized acetylene gas flow rate (100 LPH) to find out the optimum value of spark timing. In further experimentation, it is also found that the BThE to be maximum and emissions were significantly low or comparable at spark timing 20º CA bTDC (at 100 LPH) as compared to other spark timing and baseline case at all loads. The effects of NOx and smoke are not considerable. Hence, it is not covered in this study. The heat release rate and peak cylinder pressure are found to increase with the advancement of spark timing. But knocking was observed at higher spark advance.
- 20 May 2020
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 39 (5)
Effect of acetylene fuelling on performance, emission and combustion characteristics of stationary spark‐ignition engine
The continuous depletion of conventional fuels requires urgent research work to identify feasible alternative fuels to meet the minimum environmental impact of sustainable energy demand. Due to good combustion characteristics, acetylene being one of such alternative fuel and has the potential to be a future fuel. In this concern, it was decided to perform experimentation on a stationary water‐cooled spark ignition (S.I.) engine in acetylene‐gasolinedual fuel mode. In this experimental investigation, the effects of acetylene and gasoline mixtures on the performance, emissions, and combustion characteristics have been observed. Acetylene was supplied through a modified engine intake manifold at optimized conditions for petrol. The optimum flow rate of acetylene was found by comparing the performance and emissions for 50, 100, and 150 LPH, respectively, at 1600 revolution per minute (rpm). The experimental results showed that the brake thermal efficiency at 100 LPH was the highest amongst all the flow rates under study, throughout the load range in acetylene‐gasoline dual fuel mode. HC, CO, and CO2 emissions for this acetylene flow rate were either low or comparable to that of pure gasoline. Based on this study, it can be concluded that use of acetylene in S.I. engine without any major modifications is feasible without having any adverse effect on the engine performance, combustion, and emissions.
- 20 May 2020
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 39 (5)
Effect of acetylene fuelling on performance, emission and combustion characteristics of stationary spark‐ignition engine
The continuous depletion of conventional fuels requires urgent research work to identify feasible alternative fuels to meet the minimum environmental impact of sustainable energy demand. Due to good combustion characteristics, acetylene being one of such alternative fuel and has the potential to be a future fuel. In this concern, it was decided to perform experimentation on a stationary water‐cooled spark ignition (S.I.) engine in acetylene‐gasolinedual fuel mode. In this experimental investigation, the effects of acetylene and gasoline mixtures on the performance, emissions, and combustion characteristics have been observed. Acetylene was supplied through a modified engine intake manifold at optimized conditions for petrol. The optimum flow rate of acetylene was found by comparing the performance and emissions for 50, 100, and 150 LPH, respectively, at 1600 revolution per minute (rpm). The experimental results showed that the brake thermal efficiency at 100 LPH was the highest amongst all the flow rates under study, throughout the load range in acetylene‐gasoline dual fuel mode. HC, CO, and CO2 emissions for this acetylene flow rate were either low or comparable to that of pure gasoline. Based on this study, it can be concluded that use of acetylene in S.I. engine without any major modifications is feasible without having any adverse effect on the engine performance, combustion, and emissions.
- 9 March 2020
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 43 (1) , 2369-2375
Experimental investigation on spark-ignition (SI) engine fuelled with acetylene in dual-fuel mode
In this study, the effect of acetylene induction on the performance, emissions, and combustion characteristics of a petrol-acetylene fuelled spark ignition engine at 1400 rpm was experimentally investigated. Initially, the optimum flow rate of acetylene was found by analyzing the performance and emissions for different flow rates of acetylene i.e 50LPH, 100LPH, 150LPH, and 200LPH. It was observed that at 100LPH flow rate the performance was the best and major emissions were either low or comparable to other cases. After finalizing the optimum acetylene flow rate the combustion studies were carried out at this flow rate only. Pressure vs Crank angle plots indicates normal combustion with acetylene with slight abnormality at high loads. When compared with gasoline the peak pressures at different loads were found slightly higher resulting in improved combustion. Thus it can be concluded that acetylene can be a good gasoline substitute.
- 9 March 2020
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 43 (1) , 2369-2375
Experimental investigation on spark-ignition (SI) engine fuelled with acetylene in dual-fuel mode
In this study, the effect of acetylene induction on the performance, emissions, and combustion characteristics of a petrol-acetylene fuelled spark ignition engine at 1400 rpm was experimentally investigated. Initially, the optimum flow rate of acetylene was found by analyzing the performance and emissions for different flow rates of acetylene i.e 50LPH, 100LPH, 150LPH, and 200LPH. It was observed that at 100LPH flow rate the performance was the best and major emissions were either low or comparable to other cases. After finalizing the optimum acetylene flow rate the combustion studies were carried out at this flow rate only. Pressure vs Crank angle plots indicates normal combustion with acetylene with slight abnormality at high loads. When compared with gasoline the peak pressures at different loads were found slightly higher resulting in improved combustion. Thus it can be concluded that acetylene can be a good gasoline substitute.
- 1 March 2020
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 45 (15) , 8067-8081
Characterization of the hydroxy fueled compression ignition engine under dual fuel mode: Experimental and numerical simulation
- 1 March 2020
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 45 (15) , 8067-8081
Characterization of the hydroxy fueled compression ignition engine under dual fuel mode: Experimental and numerical simulation
- Top Cited Papers
A review on feedstocks, production processes, and yield for different generations of biodiesel
- Top Cited Papers
Chemical compositions, properties, and standards for different generation biodiesels: A review
- 10 September 2019
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 43 (1) , 622-640
Performance, combustion and emission analysis of internal combustion engines fuelled with acetylene – a review
- 10 September 2019
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 43 (1) , 622-640
Performance, combustion and emission analysis of internal combustion engines fuelled with acetylene – a review
- 6 January 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (5) , 4570-4587
A comprehensive review on water-emulsified diesel fuel: chemistry, engine performance and exhaust emissions
Increasing environmental concern, human health and the continuous upgradation in the stringent standards of vehicular emissions have shown much interest in cleaner diesel fuels. Out of various strategies to mitigate the diesel engine emissions, use of water blended diesel in the form of emulsion has grabbed sufficient attention of the fuel research community. Various researches have shown that water-emulsified diesel has sufficient potential to improve the engine performance simultaneously with a significant reduction in the levels of nitrogen oxides (NOx) and particulate matter (PM) emissions. Micro-explosion phenomenon of combustion in emulsion fuel helps to provide efficient and complete combustion which in turn improves brake thermal efficiency. The current study presents a comprehensive review of the usage of water-emulsified diesel fuel in CI engines. Focusing on the performance, combustion, and emission analysis, it also talks in detail about the principle and the chemistry involved in making of a stable and homogeneous water–diesel emulsion compatible for CI engine. The literature survey concludes two crucial points. First, the water-blended diesel emulsion serves as an economical, fuel efficient, and cleaner combustion technology. Second, the optimum blend ratio, emulsifier quantity, and proper process differs in almost all the research papers and hence needed to be standardized.
- 6 January 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (5) , 4570-4587
A comprehensive review on water-emulsified diesel fuel: chemistry, engine performance and exhaust emissions
Increasing environmental concern, human health and the continuous upgradation in the stringent standards of vehicular emissions have shown much interest in cleaner diesel fuels. Out of various strategies to mitigate the diesel engine emissions, use of water blended diesel in the form of emulsion has grabbed sufficient attention of the fuel research community. Various researches have shown that water-emulsified diesel has sufficient potential to improve the engine performance simultaneously with a significant reduction in the levels of nitrogen oxides (NOx) and particulate matter (PM) emissions. Micro-explosion phenomenon of combustion in emulsion fuel helps to provide efficient and complete combustion which in turn improves brake thermal efficiency. The current study presents a comprehensive review of the usage of water-emulsified diesel fuel in CI engines. Focusing on the performance, combustion, and emission analysis, it also talks in detail about the principle and the chemistry involved in making of a stable and homogeneous water–diesel emulsion compatible for CI engine. The literature survey concludes two crucial points. First, the water-blended diesel emulsion serves as an economical, fuel efficient, and cleaner combustion technology. Second, the optimum blend ratio, emulsifier quantity, and proper process differs in almost all the research papers and hence needed to be standardized.