Dilip Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dilip Sharma has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Digambar Singh
Malaviya National Institute of Technology Jaipur
3 shared publications - Sumit Sharma
Malaviya National Institute of Technology Jaipur
3 shared publications - Ahmed Hamza Hossieny Ali
Department of Mechanical Engineering, Faculty of Engineering, Assiut University, Assiut 71516, Egypt
2 shared publications - Dinesh Kumar Sharma
Department of Mechanical Engineering, Swami Keshvanand Institute of Technology, Management and Gramothan, Jaipur, India
2 shared publications - Pushpendra Kumar Sharma
Malaviya National Institute of Technology Jaipur
2 shared publications Shyam Lal Soni
2 shared publications
Latest Publications
- 25 October 2026
- Published by Wiley in Environmental Progress & Sustainable Energy
Design and performance of hybrid thermal energy storage integrated within a solar‐powered vapor absorption cooling system for milk chilling
Solar‐powered sorption cooling systems inevitably require optimized thermal energy storage to achieve consistent performance and economic viability, thereby ensuring sustainability. This study presents the design, performance, productivity, cost performance, and environmental impact of a 400 MJ hybrid sensible and latent thermal energy storage (comprising Xylitol as a phase change material and soft water as a heat transfer fluid) when integrated within a system that has a 17.5 kW single‐effect LiBr‐H 2 O vapor absorption driven by a hot water outlet from an 81 m 2 solar collector field used for cooling 1000 L of milk per day. The dynamic modeling of the entire system as a function of time is performed, along with the integration of a hybrid thermal energy storage system, using fundamental and empirical relations. Furthermore, a year‐round analysis is conducted to estimate the amount of cold energy produced and the overall system performance. The results clearly show that the system can produce up to 28,360 kWh of cold energy annually, thereby reducing annual CO 2 emissions by 2.98 tonnes in the Indian context. The economics of cooling produced with this system have been improved investigated with carbon credit‐linked incentives, which resulted in the simple and discounted payback periods of 8.9 and 12.23 years, respectively. The levelized cost of cooling of 0.103 $/kWhc has been achieved for the system, with an internal rate of return of 15.4%.
- 25 October 2026
- Published by Wiley in Environmental Progress & Sustainable Energy
Design and performance of hybrid thermal energy storage integrated within a solar‐powered vapor absorption cooling system for milk chilling
Solar‐powered sorption cooling systems inevitably require optimized thermal energy storage to achieve consistent performance and economic viability, thereby ensuring sustainability. This study presents the design, performance, productivity, cost performance, and environmental impact of a 400 MJ hybrid sensible and latent thermal energy storage (comprising Xylitol as a phase change material and soft water as a heat transfer fluid) when integrated within a system that has a 17.5 kW single‐effect LiBr‐H 2 O vapor absorption driven by a hot water outlet from an 81 m 2 solar collector field used for cooling 1000 L of milk per day. The dynamic modeling of the entire system as a function of time is performed, along with the integration of a hybrid thermal energy storage system, using fundamental and empirical relations. Furthermore, a year‐round analysis is conducted to estimate the amount of cold energy produced and the overall system performance. The results clearly show that the system can produce up to 28,360 kWh of cold energy annually, thereby reducing annual CO 2 emissions by 2.98 tonnes in the Indian context. The economics of cooling produced with this system have been improved investigated with carbon credit‐linked incentives, which resulted in the simple and discounted payback periods of 8.9 and 12.23 years, respectively. The levelized cost of cooling of 0.103 $/kWhc has been achieved for the system, with an internal rate of return of 15.4%.
- 25 June 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (54) , 82390-82410
Energy, exergy, environmental impact, and economic analyses of evacuated tube compound parabolic concentrator–powered solar thermal domestic water heating system
In the reported study, a dynamic analytical model is developed to propose the energy, exergy, environmental impact, and economic analyses of the water heating system at Jaipur (India) with an evacuated tube compound parabolic concentrator field of a total area of 81 m2. Consequently, the model is used to perform parametric studies to report the effect of operating and meteorological parameters on the productivity and performance of the system. Moreover, the system’s performance, environmental impact, and economic aspects have been investigated and compared under different meteorological conditions at four different Rajasthan (India) locations using TMY2 weather data files. Results clarified that Jodhpur receives the highest solar radiation intensity from these four locations. The model results were validated with the experimental data, and a good agreement has prevailed. Consequently, the results indicate the highest annual energy and exergy gain for Jodhpur with 79.72 MWh and 9.311 MWh, respectively, followed by Jaisalmer, Barmer, and Jaipur. The economic analysis results clarified that the simple payback period ranged from 4.5 to 4.75 years and the discounted payback period ranged from 6.6 to 7 years based on a 6% discount rate. At the same time, the levelized cost of heating for the given system is around 0.023 $/kWh which is very economical closest to that of CNG as a fuel which costs around 0.059 $/kWh. The internal rate of return is reported to be 16.76, 16.82, 16.77, and 16.75% for Barmer, Jodhpur, Jaipur, and Jaisalmer, respectively, and savings of 74.4, 78.1, 75.4, and 73.8 tonnes of CO2 emission to the environment.
- 25 June 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (54) , 82390-82410
Energy, exergy, environmental impact, and economic analyses of evacuated tube compound parabolic concentrator–powered solar thermal domestic water heating system
In the reported study, a dynamic analytical model is developed to propose the energy, exergy, environmental impact, and economic analyses of the water heating system at Jaipur (India) with an evacuated tube compound parabolic concentrator field of a total area of 81 m2. Consequently, the model is used to perform parametric studies to report the effect of operating and meteorological parameters on the productivity and performance of the system. Moreover, the system’s performance, environmental impact, and economic aspects have been investigated and compared under different meteorological conditions at four different Rajasthan (India) locations using TMY2 weather data files. Results clarified that Jodhpur receives the highest solar radiation intensity from these four locations. The model results were validated with the experimental data, and a good agreement has prevailed. Consequently, the results indicate the highest annual energy and exergy gain for Jodhpur with 79.72 MWh and 9.311 MWh, respectively, followed by Jaisalmer, Barmer, and Jaipur. The economic analysis results clarified that the simple payback period ranged from 4.5 to 4.75 years and the discounted payback period ranged from 6.6 to 7 years based on a 6% discount rate. At the same time, the levelized cost of heating for the given system is around 0.023 $/kWh which is very economical closest to that of CNG as a fuel which costs around 0.059 $/kWh. The internal rate of return is reported to be 16.76, 16.82, 16.77, and 16.75% for Barmer, Jodhpur, Jaipur, and Jaisalmer, respectively, and savings of 74.4, 78.1, 75.4, and 73.8 tonnes of CO2 emission to the environment.
- 2 December 2021
- Published by Inderscience Publishers in International Journal of Environment and Sustainable Development
- Vol. 21 (1/2) , 76-96
A review on production processes, performance and emissions analysis of hydrogen as a fuel in I.C. engines
The energy demand increases continuously with rapid increase in the world's population. Continuous depletion of limited non conventional energy resources forces the move towards alternate energy solution. Hydrogen is the environment-friendly and most promising source to meet future energy demand. Non-toxic, non-metallic and high energy content make the hydrogen as a future generation fuel. The main sources of hydrogen production are hydro, biomass, nuclear, wind, geothermal, and solar. Hydrogen can be produced from different methods like thermal, biological, electrical, and photonic. This review article provides detailed information about the production processes of hydrogen, and performance and emissions analysis of hydrogen when it is used as a fuel in internal combustion engines. Brake thermal efficiency of the engine increases with the increase of hydrogen energy share at high and moderate loads. However, at low loads, the efficiency decreases. Carbon-based emissions (HC, CO and CO
- 2 December 2021
- Published by Inderscience Publishers in International Journal of Environment and Sustainable Development
- Vol. 21 (1/2) , 76-96
A review on production processes, performance and emissions analysis of hydrogen as a fuel in I.C. engines
The energy demand increases continuously with rapid increase in the world's population. Continuous depletion of limited non conventional energy resources forces the move towards alternate energy solution. Hydrogen is the environment-friendly and most promising source to meet future energy demand. Non-toxic, non-metallic and high energy content make the hydrogen as a future generation fuel. The main sources of hydrogen production are hydro, biomass, nuclear, wind, geothermal, and solar. Hydrogen can be produced from different methods like thermal, biological, electrical, and photonic. This review article provides detailed information about the production processes of hydrogen, and performance and emissions analysis of hydrogen when it is used as a fuel in internal combustion engines. Brake thermal efficiency of the engine increases with the increase of hydrogen energy share at high and moderate loads. However, at low loads, the efficiency decreases. Carbon-based emissions (HC, CO and CO
- 27 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Impact assessment of acetylene fueling on the performance, emissions, and combustion of a spark-ignition engine
Along with industrialization and transportation, the higher living standard is also the main reason for the increase in energy demand. This increasing energy demand motivates researchers to find new alternative fuels that are eco-friendly and sustainable. In this concern, to analyze the performance, emissions, and combustion characteristics of an SI engine fueled by petrol-acetylene under DF mode is the main purpose of this study. For this purpose, a VCR spark ignition engine was used and operated at the engine maximum speed (1800 rpm). The experimental study was carried out at different acetylene gas flow rates and spark timing. In this study, the acetylene gas flow rate was first optimized on a performance basis. Furthermore, the engine was run at an optimized acetylene gas flow rate (100 LPH) to find out the optimum value of spark timing. In further experimentation, it is also found that the BThE to be maximum and emissions were significantly low or comparable at spark timing 20º CA bTDC (at 100 LPH) as compared to other spark timing and baseline case at all loads. The effects of NOx and smoke are not considerable. Hence, it is not covered in this study. The heat release rate and peak cylinder pressure are found to increase with the advancement of spark timing. But knocking was observed at higher spark advance.
- 27 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Impact assessment of acetylene fueling on the performance, emissions, and combustion of a spark-ignition engine
Along with industrialization and transportation, the higher living standard is also the main reason for the increase in energy demand. This increasing energy demand motivates researchers to find new alternative fuels that are eco-friendly and sustainable. In this concern, to analyze the performance, emissions, and combustion characteristics of an SI engine fueled by petrol-acetylene under DF mode is the main purpose of this study. For this purpose, a VCR spark ignition engine was used and operated at the engine maximum speed (1800 rpm). The experimental study was carried out at different acetylene gas flow rates and spark timing. In this study, the acetylene gas flow rate was first optimized on a performance basis. Furthermore, the engine was run at an optimized acetylene gas flow rate (100 LPH) to find out the optimum value of spark timing. In further experimentation, it is also found that the BThE to be maximum and emissions were significantly low or comparable at spark timing 20º CA bTDC (at 100 LPH) as compared to other spark timing and baseline case at all loads. The effects of NOx and smoke are not considerable. Hence, it is not covered in this study. The heat release rate and peak cylinder pressure are found to increase with the advancement of spark timing. But knocking was observed at higher spark advance.
- 9 March 2020
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 43 (1) , 2369-2375
Experimental investigation on spark-ignition (SI) engine fuelled with acetylene in dual-fuel mode
In this study, the effect of acetylene induction on the performance, emissions, and combustion characteristics of a petrol-acetylene fuelled spark ignition engine at 1400 rpm was experimentally investigated. Initially, the optimum flow rate of acetylene was found by analyzing the performance and emissions for different flow rates of acetylene i.e 50LPH, 100LPH, 150LPH, and 200LPH. It was observed that at 100LPH flow rate the performance was the best and major emissions were either low or comparable to other cases. After finalizing the optimum acetylene flow rate the combustion studies were carried out at this flow rate only. Pressure vs Crank angle plots indicates normal combustion with acetylene with slight abnormality at high loads. When compared with gasoline the peak pressures at different loads were found slightly higher resulting in improved combustion. Thus it can be concluded that acetylene can be a good gasoline substitute.
- 9 March 2020
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 43 (1) , 2369-2375
Experimental investigation on spark-ignition (SI) engine fuelled with acetylene in dual-fuel mode
In this study, the effect of acetylene induction on the performance, emissions, and combustion characteristics of a petrol-acetylene fuelled spark ignition engine at 1400 rpm was experimentally investigated. Initially, the optimum flow rate of acetylene was found by analyzing the performance and emissions for different flow rates of acetylene i.e 50LPH, 100LPH, 150LPH, and 200LPH. It was observed that at 100LPH flow rate the performance was the best and major emissions were either low or comparable to other cases. After finalizing the optimum acetylene flow rate the combustion studies were carried out at this flow rate only. Pressure vs Crank angle plots indicates normal combustion with acetylene with slight abnormality at high loads. When compared with gasoline the peak pressures at different loads were found slightly higher resulting in improved combustion. Thus it can be concluded that acetylene can be a good gasoline substitute.
- 19 February 2019
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 141 (4)
Development and Operationalization of Solar-Assisted Rapid Bulk Milk Cooler
This work aims at providing insight into developmental and operational experience of an innovative milk cooler which uses solar thermal energy for cooling of fresh milk by way of vapor absorption refrigeration system (VARS). The system uses CPC solar collector(s) producing medium temperature that is desired to provide required thermal energy to the generator of VARS. However, mismatch between the time of availability of solar energy and cooling period of milk raises a demand of integrating thermal storage to this system for use of thermal energy at appropriate times. The novelty of this work is the development of experimental setup and its operation as innovative design to meet the requirement and possible model for the industry to operate and grow using the suggested system. The design, while addressing the problem of grass root level people for generation of income, also helps in reducing the carbon footprint of milk industry, and in the world environment as a whole.
- 19 February 2019
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 141 (4)
Development and Operationalization of Solar-Assisted Rapid Bulk Milk Cooler
This work aims at providing insight into developmental and operational experience of an innovative milk cooler which uses solar thermal energy for cooling of fresh milk by way of vapor absorption refrigeration system (VARS). The system uses CPC solar collector(s) producing medium temperature that is desired to provide required thermal energy to the generator of VARS. However, mismatch between the time of availability of solar energy and cooling period of milk raises a demand of integrating thermal storage to this system for use of thermal energy at appropriate times. The novelty of this work is the development of experimental setup and its operation as innovative design to meet the requirement and possible model for the industry to operate and grow using the suggested system. The design, while addressing the problem of grass root level people for generation of income, also helps in reducing the carbon footprint of milk industry, and in the world environment as a whole.
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Renewable Energy Technology
- Vol. 10 (3) , 167
Studies on hydrogen fuelled stationary C.I. engine operated end-utility system
The world is presently confronted with the twin crisis of fossil fuel depletion and environmental degradation. The search for an alternative fuel, which promises a pleasant link with sustainable development, energy conservation, management, efficiency, and environmental safeguarding, has become highly noticeable in the present context. In this investigation, experiments were conducted on a 1-C, 4-S, air-cooled, stationary direct-injection diesel engine (Kirlosker TAF1) with maximum 1,500 rpm and maximum 4.4 kW capacity coupled to an electrical generator. The injection timing (17°, 18.5°, 20°, 21.5°, 23°, 24.5° Ca) and flow rate (80, 120, 150, 250, 600 g/hr) of hydrogen were varied with 0%, 10%, 20% and 30% EGR to find out the optimum condition for hydrogen enrichment to meet the best performance with lowest emission. It can be safely concluded that 120 g/hr hydrogen enrichment can be conveniently used at 20° CA BTDC and no major engine modifications are required for the same.
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Renewable Energy Technology
- Vol. 10 (3) , 167
Studies on hydrogen fuelled stationary C.I. engine operated end-utility system
The world is presently confronted with the twin crisis of fossil fuel depletion and environmental degradation. The search for an alternative fuel, which promises a pleasant link with sustainable development, energy conservation, management, efficiency, and environmental safeguarding, has become highly noticeable in the present context. In this investigation, experiments were conducted on a 1-C, 4-S, air-cooled, stationary direct-injection diesel engine (Kirlosker TAF1) with maximum 1,500 rpm and maximum 4.4 kW capacity coupled to an electrical generator. The injection timing (17°, 18.5°, 20°, 21.5°, 23°, 24.5° Ca) and flow rate (80, 120, 150, 250, 600 g/hr) of hydrogen were varied with 0%, 10%, 20% and 30% EGR to find out the optimum condition for hydrogen enrichment to meet the best performance with lowest emission. It can be safely concluded that 120 g/hr hydrogen enrichment can be conveniently used at 20° CA BTDC and no major engine modifications are required for the same.
- 6 September 2017
- Published by Global Research & Development Services in MATTER: International Journal of Science and Technology
- Vol. 3 (2) , 64-79
PERFORMANCE AND EMISSION ANALYSIS OF CONSTANT SPEED SI ENGINE OPERATED ON HYTHANE (HCNG)
Energy is the basic need of human to survive in this dynamic world. The whole world is toiling hard to meet its energy demands. Every country in this world has high energy demand owing to its increasing population which is posing a threat to energy sustainability. Generally, Energy is consumed in Agriculture, Residential and Transportation sector in which transportation sector has a high percentage of energy consumption. Conventional fuels which are used to power vehicles are having limited reserves. In the present scenario, Petroleum reserves are depleting at a faster rate and causing environmental pollution. It has inspired the researchers to develop new alternate fuels. Alternate fuels are having significant energy content and lower emissions as compared to conventional fuels. Alcohol, Biodiesel, Liquefied Petroleum Gas (LPG), Compressed Natural Gas (CNG) and Hydrogen are the alternate fuels which are being used today. CNG is being used extensively all over the world. CNG is having low laminar burning velocity which makes it more prone towards knocking. Hydrogen has high laminar burning velocity which makes it a better supplement to CNG. The blend thus obtained by mixing Hydrogen and CNG is known as Hythane or HCNG. Hythane has the advantages of both the parent fuels which make it a promising fuel for automotives. This paper includes the effect of Hydrogen addition to CNG which is tested on a single cylinder, four-stroke, water cooled SI engine. Determination of optimum percentage of Hydrogen in CNG and emissions analysis is also included in the paper.
- 6 September 2017
- Published by Global Research & Development Services in MATTER: International Journal of Science and Technology
- Vol. 3 (2) , 64-79
PERFORMANCE AND EMISSION ANALYSIS OF CONSTANT SPEED SI ENGINE OPERATED ON HYTHANE (HCNG)
Energy is the basic need of human to survive in this dynamic world. The whole world is toiling hard to meet its energy demands. Every country in this world has high energy demand owing to its increasing population which is posing a threat to energy sustainability. Generally, Energy is consumed in Agriculture, Residential and Transportation sector in which transportation sector has a high percentage of energy consumption. Conventional fuels which are used to power vehicles are having limited reserves. In the present scenario, Petroleum reserves are depleting at a faster rate and causing environmental pollution. It has inspired the researchers to develop new alternate fuels. Alternate fuels are having significant energy content and lower emissions as compared to conventional fuels. Alcohol, Biodiesel, Liquefied Petroleum Gas (LPG), Compressed Natural Gas (CNG) and Hydrogen are the alternate fuels which are being used today. CNG is being used extensively all over the world. CNG is having low laminar burning velocity which makes it more prone towards knocking. Hydrogen has high laminar burning velocity which makes it a better supplement to CNG. The blend thus obtained by mixing Hydrogen and CNG is known as Hythane or HCNG. Hythane has the advantages of both the parent fuels which make it a promising fuel for automotives. This paper includes the effect of Hydrogen addition to CNG which is tested on a single cylinder, four-stroke, water cooled SI engine. Determination of optimum percentage of Hydrogen in CNG and emissions analysis is also included in the paper.