Peiwen Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Peiwen Li has a total of 101 co-authors. Here are the top co-authors by number of shared publications:
Xiankun Xu
Department of Aerospace and Mechanical Engineering, The University of Arizona, Tucson, AZ, USA
6 shared publicationsBen Xu
Department of Mechanical Engineering, The University of Texas Rio Grande Valley, Edinburg, TX, USA
4 shared publicationsBharath Pidaparthi
University of Arizona Department of Aerospace and Mechanical Engineering Tucson, AZ 85721
4 shared publicationsCho Lik Chan
Department of Aerospace and Mechanical Engineering, The University of Arizona (USA)
4 shared publications- Yuesong Shen
School of Materials Science and Engineering Nanjing Tech University Nanjing China
4 shared publications Cholik Chan
3 shared publications
Latest Publications
- 10 April 2026
- Published by Elsevier in Solar Energy
- Vol. 312
Performance analysis of helium gas jet impingement heat transfer enhanced concentrating solar receiver
- 10 April 2026
- Published by Elsevier in Solar Energy
- Vol. 312
Performance analysis of helium gas jet impingement heat transfer enhanced concentrating solar receiver
- Open Access
- 1 January 2025
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Energy
- Vol. 13 (2) , 248-249
Journal Summary 2024 from Editor in Chief
- 1 January 2025
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Energy
- Vol. 13 (2) , 248-249
Open AccessJournal Summary 2024 from Editor in Chief
- 24 May 2024
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 147 (1) , 1-14
Analysis of Heat Transfer of Molten Salts Startup Flow in Cold Pipes Avoiding Freezing in Solar and Nuclear Energy Systems
Molten salts are employed as the heat transfer fluid to carry the thermal energy from a solar receiver or a nuclear reactor for delivering to thermal storage systems or thermal power plants for power generation. For the startup operation, molten salts need to be pumped to flow into the pipes which may have lower temperature than the freezing point of molten salt due to the cold ambient temperature overnight or over the suspension of operation. Preventing the freezing of molten salt in cold pipes becomes a critical issue to the safe operation of a concentrating solar thermal power plant or a molten salt nuclear power plant. This study conducted a basic heat transfer analysis of the transient heat transfer from flowing molten salt to a cold pipe to determine the length from entrance to the onset of freezing of the fluid. From our modeling and analytical solution using method of characteristics, the correlation of the location of onset of freezing of molten salt with respect to the flow velocity, heat capacities of molten salt and pipes, dimension of the pipes, and the initial temperatures of salts and pipes, have been understood clearly. The modeling and computational tool can fundamentally help engineers to design a system to avoid freezing and clogging at cold startup when molten salt is applied as a heat transfer fluid.
- 24 May 2024
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 147 (1) , 1-14
Analysis of Heat Transfer of Molten Salts Startup Flow in Cold Pipes Avoiding Freezing in Solar and Nuclear Energy Systems
Molten salts are employed as the heat transfer fluid to carry the thermal energy from a solar receiver or a nuclear reactor for delivering to thermal storage systems or thermal power plants for power generation. For the startup operation, molten salts need to be pumped to flow into the pipes which may have lower temperature than the freezing point of molten salt due to the cold ambient temperature overnight or over the suspension of operation. Preventing the freezing of molten salt in cold pipes becomes a critical issue to the safe operation of a concentrating solar thermal power plant or a molten salt nuclear power plant. This study conducted a basic heat transfer analysis of the transient heat transfer from flowing molten salt to a cold pipe to determine the length from entrance to the onset of freezing of the fluid. From our modeling and analytical solution using method of characteristics, the correlation of the location of onset of freezing of molten salt with respect to the flow velocity, heat capacities of molten salt and pipes, dimension of the pipes, and the initial temperatures of salts and pipes, have been understood clearly. The modeling and computational tool can fundamentally help engineers to design a system to avoid freezing and clogging at cold startup when molten salt is applied as a heat transfer fluid.
- Open Access
- 1 January 2024
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Energy
- Vol. 12 (1) , 271-276
Annual Report 2023
- 1 January 2024
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Energy
- Vol. 12 (1) , 271-276
Open AccessAnnual Report 2023
- 29 September 2023
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (12) , 1-12
Helical Fins for Concentrated Solar Receivers: Design Optimization and Entropy Analysis
Concentrated solar power (CSP) with thermal energy storage (TES) has the potential to achieve grid parity. This can be realized by operating CSP systems at temperatures above 700 °C with high-efficiency sCO2 power cycles. However, operating CSP systems at such temperatures poses several challenges, among which the design of solar receivers to accommodate increased thermal loads is critical. To this end, this work explores and optimizes various swirl-inducing internal fin designs for solar receiver tubes. These fin designs not only improve the thermal performance of receiver tubes but also levelize temperature unevenness caused by non-uniform thermal loading. In this work, the geometric parameters of the fin designs are optimized to maximize the Nusselt number with a constraint on the friction factor. This optimization, however, is computationally intensive, requiring hundreds of simulation calls to computational fluid dynamics (CFD) models. To circumvent this problem, surrogate models are used to approximate the simulation outputs needed during the optimization. In addition, this study also examines the fin designs from an entropy generation perspective. To this end, the entropy contributions from thermal and viscous effects are quantitatively compared while varying the operational Reynolds number.
- 29 September 2023
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (12) , 1-12
Helical Fins for Concentrated Solar Receivers: Design Optimization and Entropy Analysis
Concentrated solar power (CSP) with thermal energy storage (TES) has the potential to achieve grid parity. This can be realized by operating CSP systems at temperatures above 700 °C with high-efficiency sCO2 power cycles. However, operating CSP systems at such temperatures poses several challenges, among which the design of solar receivers to accommodate increased thermal loads is critical. To this end, this work explores and optimizes various swirl-inducing internal fin designs for solar receiver tubes. These fin designs not only improve the thermal performance of receiver tubes but also levelize temperature unevenness caused by non-uniform thermal loading. In this work, the geometric parameters of the fin designs are optimized to maximize the Nusselt number with a constraint on the friction factor. This optimization, however, is computationally intensive, requiring hundreds of simulation calls to computational fluid dynamics (CFD) models. To circumvent this problem, surrogate models are used to approximate the simulation outputs needed during the optimization. In addition, this study also examines the fin designs from an entropy generation perspective. To this end, the entropy contributions from thermal and viscous effects are quantitatively compared while varying the operational Reynolds number.
- 11 September 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 217
Thermal conductivity measurement using modulated photothermal radiometry for nitrate and chloride molten salts
- 11 September 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 217
Thermal conductivity measurement using modulated photothermal radiometry for nitrate and chloride molten salts
- 7 September 2023
- Published by Japan Society of Applied Physics
Generative Adversarial Network Applied to Neuroevolution-based Compact Device models
2023 International Conference on Solid State Devices and Materials ,Generative Adversarial Network Applied to Neuroevolution-based Compact Device models
- 7 September 2023
- Published by Japan Society of Applied Physics
Generative Adversarial Network Applied to Neuroevolution-based Compact Device models
2023 International Conference on Solid State Devices and Materials ,Generative Adversarial Network Applied to Neuroevolution-based Compact Device models
- 26 June 2023
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 146 (1) , 1-9
Optimization of Dimensions of Smooth and Twisted-Tape-Inserted Tubes for Heat Transfer with NaCl/KCl/MgCl2 Molten Salts by Principle of Entropy Generation Minimization
The entropy generation minimization principle is used as the criterion to optimize the flow and heat transfer of solar collectors and heat exchangers that use molten salts NaCl–KCl–MgCl2 and KCl–MgCl2. The Gnielinski correlation for the Nusselt number versus Reynolds number, as well as the Moody friction factor given by Petukhov, was used for the calculation of the convective heat transfer coefficient and pressure loss due to friction in smooth tubes. For twisted-tap-inserted tube, equations of Nu and friction factor provided by Manglik and Bergles were used. The objective function, the entropy generation rate of the heat transfer system, was expressed as the function of Reynolds number, Prandtl number, heating flux, tube diameter, etc. As a result of the analysis, the optimum Reynolds number was determined and thereby to determine the optimum Nusselt number, convective heat transfer coefficient, friction factor, and tube diameter, which also allows the calculation of optimum flow velocity. The analysis was conducted in the fluid temperature range of 500–700 °C, which covers the operation temperature for supercritical CO2 power cycles in concentrated solar power (CSP) system. Optimized results from the smooth tube and twisted-tap-inserted tube are compared, which is important to the design of solar receivers for CSP systems.
- 26 June 2023
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 146 (1) , 1-9
Optimization of Dimensions of Smooth and Twisted-Tape-Inserted Tubes for Heat Transfer with NaCl/KCl/MgCl2 Molten Salts by Principle of Entropy Generation Minimization
The entropy generation minimization principle is used as the criterion to optimize the flow and heat transfer of solar collectors and heat exchangers that use molten salts NaCl–KCl–MgCl2 and KCl–MgCl2. The Gnielinski correlation for the Nusselt number versus Reynolds number, as well as the Moody friction factor given by Petukhov, was used for the calculation of the convective heat transfer coefficient and pressure loss due to friction in smooth tubes. For twisted-tap-inserted tube, equations of Nu and friction factor provided by Manglik and Bergles were used. The objective function, the entropy generation rate of the heat transfer system, was expressed as the function of Reynolds number, Prandtl number, heating flux, tube diameter, etc. As a result of the analysis, the optimum Reynolds number was determined and thereby to determine the optimum Nusselt number, convective heat transfer coefficient, friction factor, and tube diameter, which also allows the calculation of optimum flow velocity. The analysis was conducted in the fluid temperature range of 500–700 °C, which covers the operation temperature for supercritical CO2 power cycles in concentrated solar power (CSP) system. Optimized results from the smooth tube and twisted-tap-inserted tube are compared, which is important to the design of solar receivers for CSP systems.