Zhiyong Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhiyong Chen has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Wenku Shi
State Key Laboratory of Automotive Simulation and Control, Jilin University, Changchun, China
9 shared publications Wenku Shi
State Key Laboratory of Automotive Simulation and Control, Jilin University, Changchun, China
6 shared publications- Henghai Zhang
State Key Laboratory of Automotive Simulation and Control, Jilin University, Changchun 130022, China
4 shared publications Haisheng Song
School of Vehicle and Traffic Engineering, Henan Institute of Technology
3 shared publications- Qiangqiang Li
Jilin University
3 shared publications Guozheng Liu
State Key Laboratory of Automotive Simulation and Control
2 shared publications
Latest Publications
- 27 September 2026
- Published by SAGE Publications in Journal of Vibration and Control
Study on bandgap modulation of partially covered cantilever-type piezoelectric phononic crystals
Low-frequency vibration and noise control remain critical challenges in automotive systems, rail transportation, and precision equipment. Cantilever-based piezoelectric phononic crystals (PPCs) exhibit wide bandgaps, strong attenuation, and compact configurations, offering considerable potential for low-frequency vibration suppression. However, conventional fully covered piezoelectric layouts suffer from limited tunability and inefficient material utilization. This study proposes a partially covered cantilever-type PPC and investigates its bandgap characteristics through theoretical modeling, numerical simulation, and experimental validation. An electromechanically coupled model is established based on Timoshenko beam theory and the Precise Integration Method, and the band structure is derived using the Transfer Matrix Method. Finite element simulations demonstrate high accuracy of the proposed formulation in predicting localized resonance bandgaps. Vibration transmissibility experiments conducted on a six-period prototype further confirm the predicted bandgap locations and support the validity of the theoretical model. The influence of different shunt circuit configurations is analyzed, showing that RC circuits effectively suppress electrical resonance and improve bandgap stability. A modulation factor is introduced to quantify tunability, and its dependence on key geometric parameters is examined. The results show that, for the same short-circuit bandgap center frequency of 702 Hz, the partially covered design expands the tunable bandgap range from 615–764 Hz to 589–791 Hz. Consequently, the tuning efficiency is improved by 7.67% while the piezoelectric material usage is reduced by 38.69%. The underlying mechanism is further clarified by showing that the enhanced tunability arises from the competition between electrically induced stiffness modulation and inertia effects, which governs the effectiveness of piezoelectric material distribution. These findings demonstrate enhanced tunability and material utilization efficiency.
- 27 September 2026
- Published by SAGE Publications in Journal of Vibration and Control
Study on bandgap modulation of partially covered cantilever-type piezoelectric phononic crystals
Low-frequency vibration and noise control remain critical challenges in automotive systems, rail transportation, and precision equipment. Cantilever-based piezoelectric phononic crystals (PPCs) exhibit wide bandgaps, strong attenuation, and compact configurations, offering considerable potential for low-frequency vibration suppression. However, conventional fully covered piezoelectric layouts suffer from limited tunability and inefficient material utilization. This study proposes a partially covered cantilever-type PPC and investigates its bandgap characteristics through theoretical modeling, numerical simulation, and experimental validation. An electromechanically coupled model is established based on Timoshenko beam theory and the Precise Integration Method, and the band structure is derived using the Transfer Matrix Method. Finite element simulations demonstrate high accuracy of the proposed formulation in predicting localized resonance bandgaps. Vibration transmissibility experiments conducted on a six-period prototype further confirm the predicted bandgap locations and support the validity of the theoretical model. The influence of different shunt circuit configurations is analyzed, showing that RC circuits effectively suppress electrical resonance and improve bandgap stability. A modulation factor is introduced to quantify tunability, and its dependence on key geometric parameters is examined. The results show that, for the same short-circuit bandgap center frequency of 702 Hz, the partially covered design expands the tunable bandgap range from 615–764 Hz to 589–791 Hz. Consequently, the tuning efficiency is improved by 7.67% while the piezoelectric material usage is reduced by 38.69%. The underlying mechanism is further clarified by showing that the enhanced tunability arises from the competition between electrically induced stiffness modulation and inertia effects, which governs the effectiveness of piezoelectric material distribution. These findings demonstrate enhanced tunability and material utilization efficiency.
- 26 August 2026
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 645
A set-membership filtered-x normalized LMS algorithm with correntropy-induced metric constraint for active noise control
- 26 August 2026
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 645
A set-membership filtered-x normalized LMS algorithm with correntropy-induced metric constraint for active noise control
- 10 January 2026
- Published by Elsevier in Digital Signal Processing
- Vol. 173
Logarithmic-sum function constrained set-membership FxNLMS algorithm for active noise control
- 10 January 2026
- Published by Elsevier in Digital Signal Processing
- Vol. 173
Logarithmic-sum function constrained set-membership FxNLMS algorithm for active noise control
- Open Access
A Overview of Energy Management Strategies for Hybrid Power Systems
This paper systematically reviews and analyzes various energy management strategies, as well as the characteristics, core challenges, and general processes of energy management for hybrid vehicles, aircraft, and ships. It also Analyzes the application scenarios, advantages, and limitations of rule-based energy management strategies. Based on the characteristics, design challenges, and general processes of optimized energy management strategies, a comparative analysis was conducted of mainstream strategies such as dynamic programming algorithms, Pontryagin’s minimum principle, equivalent energy consumption minimization, and multi-objective prediction. The focus was on analyzing intelligent control energy management strategies, including hybrid power system energy management strategies and their control effects based on neural network control, adaptive dynamic programming, reinforcement learning, and deep reinforcement learning. Finally, this paper addresses the challenges in applying energy management strategies, the limitations of modeling approaches, the validation of their effectiveness, and future research directions.
Open AccessA Overview of Energy Management Strategies for Hybrid Power Systems
This paper systematically reviews and analyzes various energy management strategies, as well as the characteristics, core challenges, and general processes of energy management for hybrid vehicles, aircraft, and ships. It also Analyzes the application scenarios, advantages, and limitations of rule-based energy management strategies. Based on the characteristics, design challenges, and general processes of optimized energy management strategies, a comparative analysis was conducted of mainstream strategies such as dynamic programming algorithms, Pontryagin’s minimum principle, equivalent energy consumption minimization, and multi-objective prediction. The focus was on analyzing intelligent control energy management strategies, including hybrid power system energy management strategies and their control effects based on neural network control, adaptive dynamic programming, reinforcement learning, and deep reinforcement learning. Finally, this paper addresses the challenges in applying energy management strategies, the limitations of modeling approaches, the validation of their effectiveness, and future research directions.
- Open Access
- 25 February 2025
- Published by SAGE Publications in Journal of Low Frequency Noise, Vibration and Active Control
- Vol. 44 (3) , 1855-1875
Research and application of the algorithm editing method for improving active noise control performance
In the field of active noise control systems, combining multiple algorithms to improve equalization performance has generated notable interest. Nevertheless, the computation of threshold control parameters for algorithm switching during each iteration leads to a significant increase in computational complexity. Additionally, the frequent switching of algorithms poses challenges in fully leveraging the performance of individual algorithms. Therefore, this paper utilizes the film editing concept to introduce the Algorithm Editing Method (AEM). AEM entails selecting appropriate algorithms based on distinctive iteration stages, followed by precise cutting and splicing according to the defined switching coefficient. Appropriate algorithms are implemented at specific iteration stages, eliminating the requirement for frequent algorithm switching during the iterative process. To substantiate the effectiveness of this approach, the FxLMS and Momentum-FxLMS algorithms serve as foundational components of AEM, enhancing convergence performance in an active noise control system. The results show a noteworthy enhancement in convergence speed and reduction of steady-state error, attained without a simultaneous escalation in computational complexity. Additionally, this study extends the application of AEM to improve the system’s robustness against impulse signals. The simulations and tests results demonstrate the method’s effectiveness, achieving a balance of optimized convergence speed, reduction in steady-state error, and minimized computational complexity.
- 25 February 2025
- Published by SAGE Publications in Journal of Low Frequency Noise, Vibration and Active Control
- Vol. 44 (3) , 1855-1875
Open AccessResearch and application of the algorithm editing method for improving active noise control performance
In the field of active noise control systems, combining multiple algorithms to improve equalization performance has generated notable interest. Nevertheless, the computation of threshold control parameters for algorithm switching during each iteration leads to a significant increase in computational complexity. Additionally, the frequent switching of algorithms poses challenges in fully leveraging the performance of individual algorithms. Therefore, this paper utilizes the film editing concept to introduce the Algorithm Editing Method (AEM). AEM entails selecting appropriate algorithms based on distinctive iteration stages, followed by precise cutting and splicing according to the defined switching coefficient. Appropriate algorithms are implemented at specific iteration stages, eliminating the requirement for frequent algorithm switching during the iterative process. To substantiate the effectiveness of this approach, the FxLMS and Momentum-FxLMS algorithms serve as foundational components of AEM, enhancing convergence performance in an active noise control system. The results show a noteworthy enhancement in convergence speed and reduction of steady-state error, attained without a simultaneous escalation in computational complexity. Additionally, this study extends the application of AEM to improve the system’s robustness against impulse signals. The simulations and tests results demonstrate the method’s effectiveness, achieving a balance of optimized convergence speed, reduction in steady-state error, and minimized computational complexity.
- Open Access
- 17 December 2024
- Published by SAGE Publications in Journal of Low Frequency Noise, Vibration and Active Control
- Vol. 44 (2) , 1200-1219
Vehicle active suspension control considering parameter uncertainty and velocity variation
Due to the uncertainty in vehicle model parameters, the control performance of active suspensions often deteriorates, especially under extreme conditions such as high velocities and full loads. To address this challenge, this paper proposes a novel robust finite frequency H ∞ output feedback control strategy based on linear parameter varying (LPV) systems. First, we establish a new LPV model for the half-car active suspension control system, taking into account the uncertainties associated with vehicle velocity and sprung mass. Next, a robust finite frequency H ∞ output feedback controller is designed using a gain scheduling approach, formulated through a set of linear matrix inequalities (LMIs). Finally, simulation results demonstrate that the proposed velocity-dependent robust control strategy significantly reduces the root mean square (RMS) values of vertical acceleration by approximately 21% to 31% under various conditions of sprung mass and vehicle speed compared to traditional control methods.
- 17 December 2024
- Published by SAGE Publications in Journal of Low Frequency Noise, Vibration and Active Control
- Vol. 44 (2) , 1200-1219
Open AccessVehicle active suspension control considering parameter uncertainty and velocity variation
Due to the uncertainty in vehicle model parameters, the control performance of active suspensions often deteriorates, especially under extreme conditions such as high velocities and full loads. To address this challenge, this paper proposes a novel robust finite frequency H ∞ output feedback control strategy based on linear parameter varying (LPV) systems. First, we establish a new LPV model for the half-car active suspension control system, taking into account the uncertainties associated with vehicle velocity and sprung mass. Next, a robust finite frequency H ∞ output feedback controller is designed using a gain scheduling approach, formulated through a set of linear matrix inequalities (LMIs). Finally, simulation results demonstrate that the proposed velocity-dependent robust control strategy significantly reduces the root mean square (RMS) values of vertical acceleration by approximately 21% to 31% under various conditions of sprung mass and vehicle speed compared to traditional control methods.
- Open Access
Model Predictive Control for Speed-Dependent Active Suspension System with Road Preview Information
This paper proposes a model predictive control (MPC) scheme based on linear parameter variation to enhance the damping control of speed-dependent active suspensions. The controller is developed by introducing a speed-dependent term, specifically front- and rear-wheel time delays, to the half-car model using the Padé approximation. Subsequently, the model is augmented with time-varying parameter dependence. An adaptive Kalman filter based on variance matching is employed to estimate system states affected by imprecise sensor measurement noise. Finally, a set of explicit control laws incorporating road preview information and available vehicle speed are determined offline using multi-parameter linear programming (mp-LP), simplifying online implementation to searching for optimal solutions in a lookup table. Simulation results demonstrate a significant improvement in active suspension control under changing vehicle speeds compared to passive control.
Open AccessModel Predictive Control for Speed-Dependent Active Suspension System with Road Preview Information
This paper proposes a model predictive control (MPC) scheme based on linear parameter variation to enhance the damping control of speed-dependent active suspensions. The controller is developed by introducing a speed-dependent term, specifically front- and rear-wheel time delays, to the half-car model using the Padé approximation. Subsequently, the model is augmented with time-varying parameter dependence. An adaptive Kalman filter based on variance matching is employed to estimate system states affected by imprecise sensor measurement noise. Finally, a set of explicit control laws incorporating road preview information and available vehicle speed are determined offline using multi-parameter linear programming (mp-LP), simplifying online implementation to searching for optimal solutions in a lookup table. Simulation results demonstrate a significant improvement in active suspension control under changing vehicle speeds compared to passive control.
- Open Access
- 19 January 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-16
Adaptive suspension state estimation based on IMMAKF on variable vehicle speed, road roughness grade and sprung mass condition
Vehicle speed, road roughness grade and sprung mass are the three main factors to influence suspension control and state estimation. Aiming at the problem that fixed state observer cannot guarantee the estimation accuracy of suspension with driving scenario changes, a suspension state observer based on interactive multiple model adaptive Kalman filter (IMMAKF) is established. Firstly, an adaptive control suspension is proposed based on LQR algorithm and multi-objective optimization algorithm, which can automatically adjust the controller parameters according to the vehicle speed, road roughness grade and sprung acceleration parameters, so as to keep the optimal control effect of the suspension. Secondly, the theoretical model of IMMAKF is derived, and two kinds of IMMAKF suspension state observers and controllers are established. Finally, a simulation condition with the vehicle speed, road roughness grade and sprung mass changing simultaneously is established. The simulation results shows that: compared with ordinary IMMKF, AKF and KF observers, the estimation accuracy of IMMAKF5 is improved. Except for state observation, IMMAKF can be used to identify the road roughness grade and estimate the suspension sprung mass.
- 19 January 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-16
Open AccessAdaptive suspension state estimation based on IMMAKF on variable vehicle speed, road roughness grade and sprung mass condition
Vehicle speed, road roughness grade and sprung mass are the three main factors to influence suspension control and state estimation. Aiming at the problem that fixed state observer cannot guarantee the estimation accuracy of suspension with driving scenario changes, a suspension state observer based on interactive multiple model adaptive Kalman filter (IMMAKF) is established. Firstly, an adaptive control suspension is proposed based on LQR algorithm and multi-objective optimization algorithm, which can automatically adjust the controller parameters according to the vehicle speed, road roughness grade and sprung acceleration parameters, so as to keep the optimal control effect of the suspension. Secondly, the theoretical model of IMMAKF is derived, and two kinds of IMMAKF suspension state observers and controllers are established. Finally, a simulation condition with the vehicle speed, road roughness grade and sprung mass changing simultaneously is established. The simulation results shows that: compared with ordinary IMMKF, AKF and KF observers, the estimation accuracy of IMMAKF5 is improved. Except for state observation, IMMAKF can be used to identify the road roughness grade and estimate the suspension sprung mass.
- 5 March 2023
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 193
Vibration control of commercial vehicle drive axles based on modification of helical gears
- 5 March 2023
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 193
Vibration control of commercial vehicle drive axles based on modification of helical gears
- Open Access
A Novel State Estimation Approach for Suspension System with Time-Varying and Unknown Noise Covariance
In this paper, a novel state estimation approach based on the variational Bayesian adaptive Kalman filter (VBAKF) and road classification is proposed for a suspension system with time-varying and unknown noise covariance. Using the VB approach, the time-varying noise covariance can be inferred from the inverse-Wishart distribution and then optimized state estimation by the finite sampling posterior probability distribution function (PDF) of noise covariance and backward Kalman smoothing. In addition, a new road classification algorithm based on multi-objective optimization and the linear classifier is proposed to identify the unknown noise covariance. Simulation results for a suspension model with time-varying and unknown noise covariance show that the proposed approach has a higher performance in state estimation accuracy than other filters.
Open AccessA Novel State Estimation Approach for Suspension System with Time-Varying and Unknown Noise Covariance
In this paper, a novel state estimation approach based on the variational Bayesian adaptive Kalman filter (VBAKF) and road classification is proposed for a suspension system with time-varying and unknown noise covariance. Using the VB approach, the time-varying noise covariance can be inferred from the inverse-Wishart distribution and then optimized state estimation by the finite sampling posterior probability distribution function (PDF) of noise covariance and backward Kalman smoothing. In addition, a new road classification algorithm based on multi-objective optimization and the linear classifier is proposed to identify the unknown noise covariance. Simulation results for a suspension model with time-varying and unknown noise covariance show that the proposed approach has a higher performance in state estimation accuracy than other filters.