Scott I. Jackson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Scott I. Jackson has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Eric Karl Anderson
Los Alamos National Laboratory 1 , Los Alamos, New Mexico 87545
10 shared publications - Joseph Emmett Shepherd
California Institute of Technology
8 shared publications Mark Short
7 shared publications- Mark Short
Los Alamos National Laboratory
7 shared publications - Carlos Chiquete
Los Alamos National Laboratory 1 , Los Alamos, New Mexico 87545
6 shared publications Larry G. Hill
5 shared publications
Latest Publications
- 7 October 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (13)
Evaluation of liquid equation of state for deuterium oxide (D2O) and perfluorooctane (C8F18) via tamped Richtmyer–Meshkov instability experiments
Window materials in shock compression experiments maintain shock stresses in samples and enable optical velocimetry measurements of the sample–window interface. Transparent liquids present unique opportunities as negligible-strength window materials that conform to nonuniform surfaces without adhesives or gaps. The equation of state (EOS) and dynamic strength of shock-loaded materials must be defined to accurately predict their behavior. Traditionally, these properties are characterized through separate experiments, including uniaxial-strain shock compression experiments for EOS and pressure-shear experiments for dynamic strength. More recently, the tamped Richtmyer–Meshkov instability (RMI) method was developed to measure dynamic strength through combined experiment and simulation. Here, we improve the tamped RMI method by directly determining the shock-compressed state of liquid tamper materials from dynamic radiographs. Impact experiments driving shock waves across corrugated metal–liquid interfaces at 2.5–5.2 km/s were recorded using x-ray phase contrast imaging. Radiographs of the tamper response were analyzed to define the EOS of D2O and C8F18. Material interface and shock wave locations were tracked to obtain shock and particle velocities, which calibrated linear shock-particle velocity Hugoniot relationships serving as reference curves for EOS surfaces, such as the Mie–Grüneisen EOS. The resulting EOS is compared to prior data and can be used in designing and analyzing experiments employing D2O and C8F18 as liquid windows. This method extends the utility of the tamped RMI method by allowing measurement of a sample EOS in addition to dynamic strength.
- 7 October 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (13)
Evaluation of liquid equation of state for deuterium oxide (D2O) and perfluorooctane (C8F18) via tamped Richtmyer–Meshkov instability experiments
Window materials in shock compression experiments maintain shock stresses in samples and enable optical velocimetry measurements of the sample–window interface. Transparent liquids present unique opportunities as negligible-strength window materials that conform to nonuniform surfaces without adhesives or gaps. The equation of state (EOS) and dynamic strength of shock-loaded materials must be defined to accurately predict their behavior. Traditionally, these properties are characterized through separate experiments, including uniaxial-strain shock compression experiments for EOS and pressure-shear experiments for dynamic strength. More recently, the tamped Richtmyer–Meshkov instability (RMI) method was developed to measure dynamic strength through combined experiment and simulation. Here, we improve the tamped RMI method by directly determining the shock-compressed state of liquid tamper materials from dynamic radiographs. Impact experiments driving shock waves across corrugated metal–liquid interfaces at 2.5–5.2 km/s were recorded using x-ray phase contrast imaging. Radiographs of the tamper response were analyzed to define the EOS of D2O and C8F18. Material interface and shock wave locations were tracked to obtain shock and particle velocities, which calibrated linear shock-particle velocity Hugoniot relationships serving as reference curves for EOS surfaces, such as the Mie–Grüneisen EOS. The resulting EOS is compared to prior data and can be used in designing and analyzing experiments employing D2O and C8F18 as liquid windows. This method extends the utility of the tamped RMI method by allowing measurement of a sample EOS in addition to dynamic strength.
- Open Access
- 13 August 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (6)
The effect of aging and charge variability on the detonation performance of a conventional plastic-bonded high explosive
Plastic-bonded explosives (PBXs) are pressed composites of energetic crystals (>90 wt. %), polymeric binder, and an internal porosity structure (1–2 vol. %). The binder ensures material stability, while porosity promotes more reliable reaction initiation. These microstructural features critically influence the bulk mechanical and detonation performance properties of the high explosive (HE), yet the connection between microstructure and bulk behavior remains incompletely understood, complicating both manufacture and characterization. Aging of HE constituents under varying environmental conditions introduces additional uncertainty. For PBXs composed of cyclotetramethylene–tetranitramine (HMX), it is commonly assumed that detonation performance, specifically detonation velocity and energy release, are insensitive to microstructural details and do not vary significantly over time. This assumption simplifies constitutive modeling choices at the engineering scale. Here, we analyze four high-precision cylinder expansion tests of an HMX-based PBX varying in molding powder lot, pressing method, final pressed density, and pressing age. These data support hydrocode-based model calibrations of the explosive product equation of state, and these are used to quantify the effect of the described material variability on energy release characteristics. The results indicate that the detonation velocity increases with density and may also increase with age, though further experiments would be required for confirmation. No significant variation in energy delivery was observed across the tests.
- 13 August 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (6)
Open AccessThe effect of aging and charge variability on the detonation performance of a conventional plastic-bonded high explosive
Plastic-bonded explosives (PBXs) are pressed composites of energetic crystals (>90 wt. %), polymeric binder, and an internal porosity structure (1–2 vol. %). The binder ensures material stability, while porosity promotes more reliable reaction initiation. These microstructural features critically influence the bulk mechanical and detonation performance properties of the high explosive (HE), yet the connection between microstructure and bulk behavior remains incompletely understood, complicating both manufacture and characterization. Aging of HE constituents under varying environmental conditions introduces additional uncertainty. For PBXs composed of cyclotetramethylene–tetranitramine (HMX), it is commonly assumed that detonation performance, specifically detonation velocity and energy release, are insensitive to microstructural details and do not vary significantly over time. This assumption simplifies constitutive modeling choices at the engineering scale. Here, we analyze four high-precision cylinder expansion tests of an HMX-based PBX varying in molding powder lot, pressing method, final pressed density, and pressing age. These data support hydrocode-based model calibrations of the explosive product equation of state, and these are used to quantify the effect of the described material variability on energy release characteristics. The results indicate that the detonation velocity increases with density and may also increase with age, though further experiments would be required for confirmation. No significant variation in energy delivery was observed across the tests.
- Open Access
- 12 August 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Detonation front modes in arced channels
- 12 August 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Open AccessDetonation front modes in arced channels
- Open Access
- 29 July 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Flame speed enhancement in narrow channels of low effusivity aerogel
- 29 July 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Open AccessFlame speed enhancement in narrow channels of low effusivity aerogel
- Open Access
- 20 July 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Multivariate distribution analysis of detonation cell irregularity
- 20 July 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Open AccessMultivariate distribution analysis of detonation cell irregularity
- Open Access
- 9 July 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Characterization of an ethylene–oxygen predetonator for high-speed combustors
- 9 July 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Open AccessCharacterization of an ethylene–oxygen predetonator for high-speed combustors
- Open Access
- 30 September 2025
- Published by Elsevier in Combustion and Flame
- Vol. 282
Cell size and DDT scaling for ethylene–oxygen–nitrogen detonation
- 30 September 2025
- Published by Elsevier in Combustion and Flame
- Vol. 282
Open AccessCell size and DDT scaling for ethylene–oxygen–nitrogen detonation
- Open Access
- 11 January 2024
- Published by Elsevier in Combustion and Flame
- Vol. 261
Effect of elevated initial temperature on the detonation performance of high explosives
- 11 January 2024
- Published by Elsevier in Combustion and Flame
- Vol. 261
Open AccessEffect of elevated initial temperature on the detonation performance of high explosives
- Open Access
- 22 June 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (24)
Validation of a detonation product equation of state for an insensitive high explosive via slab geometry expansion tests
Slab expansion (SLABEX) tests are conducted to validate a process for calibrating the detonation products equation of state (EOS) of a high explosive (HE). The SLABEX tests use rectangular slabs of PBX 9502, a polymer-bonded HE formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene bound with Kel F-800, a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Three PBX 9502 slab thicknesses are examined, each confined symmetrically by two rectangular copper (Cu) plates approximately one-tenth the thickness of the HE slab. For the duration of each experiment, the detonation flow along the central axis of the PBX 9502 slab remains two-dimensional. The lateral flow velocity component of the outer surfaces of the expanding Cu plates is measured, along with the steady axial detonation speed along the central axis of the SLABEX. Hydrodynamic simulations of the Cu plate expansion in the SLABEX geometry, driven by the energy stored in the detonation products by the detonation combustion event, are conducted using a Jones–Wilkins–Lee EOS for the detonation products. This EOS form was recently parameterized for PBX 9502 in the cylinder expansion test geometry using a newly developed calibration technique [Voelkel et al., Combust. Flame 246, 112373 (2022)]. Good agreement between the experiment and prediction is found in each SLABEX test, demonstrating that the detonation product EOS calibration technique produces EOSs that are predictive when applied to other geometries.
- 22 June 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (24)
Open AccessValidation of a detonation product equation of state for an insensitive high explosive via slab geometry expansion tests
Slab expansion (SLABEX) tests are conducted to validate a process for calibrating the detonation products equation of state (EOS) of a high explosive (HE). The SLABEX tests use rectangular slabs of PBX 9502, a polymer-bonded HE formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene bound with Kel F-800, a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Three PBX 9502 slab thicknesses are examined, each confined symmetrically by two rectangular copper (Cu) plates approximately one-tenth the thickness of the HE slab. For the duration of each experiment, the detonation flow along the central axis of the PBX 9502 slab remains two-dimensional. The lateral flow velocity component of the outer surfaces of the expanding Cu plates is measured, along with the steady axial detonation speed along the central axis of the SLABEX. Hydrodynamic simulations of the Cu plate expansion in the SLABEX geometry, driven by the energy stored in the detonation products by the detonation combustion event, are conducted using a Jones–Wilkins–Lee EOS for the detonation products. This EOS form was recently parameterized for PBX 9502 in the cylinder expansion test geometry using a newly developed calibration technique [Voelkel et al., Combust. Flame 246, 112373 (2022)]. Good agreement between the experiment and prediction is found in each SLABEX test, demonstrating that the detonation product EOS calibration technique produces EOSs that are predictive when applied to other geometries.
- 18 July 2022
- Published by Springer Nature in Shock Waves
- Vol. 32 (5) , 427-436
An experimental study of shock transmission from a detonation tube
- 18 July 2022
- Published by Springer Nature in Shock Waves
- Vol. 32 (5) , 427-436
An experimental study of shock transmission from a detonation tube