Mauro Passarotto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mauro Passarotto has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Ruben Specogna
EMC Lab, University of Udine, Udine, Italy
9 shared publications - Aldi Hoxha
EMCLab, DPIA, University of Udine, Udine, Italy
2 shared publications Paolo Bettini
Consorzio RFX, Padua, Italy
2 shared publications- Bernard Kapidani
Institute for Analysis and Scientific Computing, TU Wien, Vienna, Austria
1 shared publication - Christophe Geuzaine
University of Liège
1 shared publication Daniel Klis
Robert Bosch GmbH, 71272 Renningen, Germany
1 shared publication
Latest Publications
- Open Access
Design Optimization of PCB-Based Rotary-Inductive Position Sensors
This paper introduces a novel methodology to optimize the design of a ratiometric rotary inductive position sensor (IPS) fabricated in printed circuit board (PCB) technology. The optimization aims at reducing the linearity error of the sensor and amplitude mismatch between the voltages on the two receiving (RX) coils. Distinct from other optimization techniques proposed in the literature, the sensor footprint and the target geometry are considered as a non-modifiable input. This is motivated by the fact that, for sensor replacement purposes, the target has to fit a predefined space. For this reason, the original optimization technique proposed in this paper modifies the shape of the RX coils to reproduce theoretical coil voltages as much as possible. The optimized RX shape was obtained by means of a non-linear least-square solver, whereas the electromagnetic simulation of the sensor is performed with an original surface integral method, which are orders of magnitude faster than commercial software based on finite elements. Comparisons between simulations and measurements performed on different prototypes of an absolute rotary sensor show the effectiveness of the optimization tool. The optimized sensors exhibit a linearity error below 0.1% of the full scale (FS) without any signal calibration or post-processing manipulation.
Open AccessDesign Optimization of PCB-Based Rotary-Inductive Position Sensors
This paper introduces a novel methodology to optimize the design of a ratiometric rotary inductive position sensor (IPS) fabricated in printed circuit board (PCB) technology. The optimization aims at reducing the linearity error of the sensor and amplitude mismatch between the voltages on the two receiving (RX) coils. Distinct from other optimization techniques proposed in the literature, the sensor footprint and the target geometry are considered as a non-modifiable input. This is motivated by the fact that, for sensor replacement purposes, the target has to fit a predefined space. For this reason, the original optimization technique proposed in this paper modifies the shape of the RX coils to reproduce theoretical coil voltages as much as possible. The optimized RX shape was obtained by means of a non-linear least-square solver, whereas the electromagnetic simulation of the sensor is performed with an original surface integral method, which are orders of magnitude faster than commercial software based on finite elements. Comparisons between simulations and measurements performed on different prototypes of an absolute rotary sensor show the effectiveness of the optimization tool. The optimized sensors exhibit a linearity error below 0.1% of the full scale (FS) without any signal calibration or post-processing manipulation.
- 10 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 58 (9) , 1-4
Fast Computation of Eddy Currents for Multiple Conductors
In this work the solution of the eddy current problem for slowly moving conductors is investigated with the volume integral formulation of the EFIE. If in one hand the formulation gives the possibility to mesh only the conductors, if embedded in a uniform insulator, on the other hand the inductance matrix is fully populated limiting thus the size of the problem. Furthermore, the standard solution implies the reassembling of the stiffness matrix for each position assumed by the moving conductors. This results in a limit in the size of the problem to treat and a relevant cost in the computation time. To overcome this limit, in this work, the mutual coupling part of the system with two conductors is computed on the fly giving thus the possibility to solve problems with a higher number of unknowns. Finally, to speed up the solution of the system, the Gauss–Seidel iterative techniques and the Fast Multipole Method (FMM) are applied to take into account the mutual effects between the conductors. A comparison of the proposed method with a reference one shows the effectiveness of this technique.
- 10 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 58 (9) , 1-4
Fast Computation of Eddy Currents for Multiple Conductors
In this work the solution of the eddy current problem for slowly moving conductors is investigated with the volume integral formulation of the EFIE. If in one hand the formulation gives the possibility to mesh only the conductors, if embedded in a uniform insulator, on the other hand the inductance matrix is fully populated limiting thus the size of the problem. Furthermore, the standard solution implies the reassembling of the stiffness matrix for each position assumed by the moving conductors. This results in a limit in the size of the problem to treat and a relevant cost in the computation time. To overcome this limit, in this work, the mutual coupling part of the system with two conductors is computed on the fly giving thus the possibility to solve problems with a higher number of unknowns. Finally, to speed up the solution of the system, the Gauss–Seidel iterative techniques and the Fast Multipole Method (FMM) are applied to take into account the mutual effects between the conductors. A comparison of the proposed method with a reference one shows the effectiveness of this technique.
- 22 February 2022
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 392
Foundations of volume integral methods for eddy current problems
- 22 February 2022
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 392
Foundations of volume integral methods for eddy current problems
- 10 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 57 (6) , 1-4
Mirror Symmetry in Integral Formulations for Eddy Currents
This contribution addresses the exploitation of mirror symmetry (formally, the abelian D1 and D2 dihedral symmetry groups) in various integral formulations for eddy current problems. The novelty of the contribution is in particular how to rigorously treat non simply-connected conductors when computing first cohomology group generators on the symmetry cell of the problem only.
- 10 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 57 (6) , 1-4
Mirror Symmetry in Integral Formulations for Eddy Currents
This contribution addresses the exploitation of mirror symmetry (formally, the abelian D1 and D2 dihedral symmetry groups) in various integral formulations for eddy current problems. The novelty of the contribution is in particular how to rigorously treat non simply-connected conductors when computing first cohomology group generators on the symmetry cell of the problem only.
- 13 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 56 (2) , 1-4
Cyclic Symmetry in Volume Integral Formulations for Eddy Currents: Cohomology Computation and Gauging
This contribution addresses the solution of eddy-current problems by means of a volume integral formulation based on the electric vector potential on a computational domain that exhibits a cyclic symmetry. Even if grids discretizing the domain are typically composed of tetrahedral or hexahedral elements, the proposed approach also works for general polyhedral meshes, such as those ones obtained by subgridding. In this article, an algorithm to compute a set of suitable cohomology generators needed when the conductors are not simply connected is introduced first. Besides being purely combinatorial, with linear-time worst case complexity and suitable with polyhedral meshes, it reuses a code that computes generators for triangular surface meshes, with obvious advantages concerning the implementation effort. Second, the formulation and the algorithm for cohomology computation are tweaked to be able to solve eddy-current problems with cyclic symmetry reserving specific attention to the construction of suitable tree-cotree decomposition for the problem gauging.
- 13 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 56 (2) , 1-4
Cyclic Symmetry in Volume Integral Formulations for Eddy Currents: Cohomology Computation and Gauging
This contribution addresses the solution of eddy-current problems by means of a volume integral formulation based on the electric vector potential on a computational domain that exhibits a cyclic symmetry. Even if grids discretizing the domain are typically composed of tetrahedral or hexahedral elements, the proposed approach also works for general polyhedral meshes, such as those ones obtained by subgridding. In this article, an algorithm to compute a set of suitable cohomology generators needed when the conductors are not simply connected is introduced first. Besides being purely combinatorial, with linear-time worst case complexity and suitable with polyhedral meshes, it reuses a code that computes generators for triangular surface meshes, with obvious advantages concerning the implementation effort. Second, the formulation and the algorithm for cohomology computation are tweaked to be able to solve eddy-current problems with cyclic symmetry reserving specific attention to the construction of suitable tree-cotree decomposition for the problem gauging.
- 3 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (6) , 1-4
Exploiting Cyclic Symmetry in Stream Function-Based Boundary Integral Formulations
This contribution addresses the exploitation of cyclic symmetry in boundary integral formulations for eddy current problems formulated with a magnetic scalar potential. The novelty of the contribution is how to rigorously treat non-simply connected conductors. In particular, a general algorithm to compute a set of suitable cohomology generators is introduced. The algorithm is purely combinatorial and exhibits a linear-time worst-case complexity.
- 3 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (6) , 1-4
Exploiting Cyclic Symmetry in Stream Function-Based Boundary Integral Formulations
This contribution addresses the exploitation of cyclic symmetry in boundary integral formulations for eddy current problems formulated with a magnetic scalar potential. The novelty of the contribution is how to rigorously treat non-simply connected conductors. In particular, a general algorithm to compute a set of suitable cohomology generators is introduced. The algorithm is purely combinatorial and exhibits a linear-time worst-case complexity.
- 6 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (6) , 1-4
Novel Geometrically Defined Mass Matrices for Tetrahedral Meshes
- 6 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (6) , 1-4
Novel Geometrically Defined Mass Matrices for Tetrahedral Meshes
- 8 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 64 (7) , 1983-1987
Fast and Efficient Algorithms for Computational Electromagnetics on GPU Architecture
Magnetic diagnostics are essential for the operation and understanding of a magnetic confinement fusion (MCF) device, for example, by providing in real-time, the axisymmetric measurements needed for plasma equilibrium reconstructions or magnetohydrodynamic instabilities control. In this paper, we present a fast and robust implementation on GPU architecture of an accurate algorithm suitable for the computation of synthetic magnetic measurements used both in real time applications and off-line reconstruction procedures. The proposed procedure is first applied to benchmark problems, to validate the compute unified device architecture implementation, and then to cases of practical interests in MCF.
- 8 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 64 (7) , 1983-1987
Fast and Efficient Algorithms for Computational Electromagnetics on GPU Architecture
Magnetic diagnostics are essential for the operation and understanding of a magnetic confinement fusion (MCF) device, for example, by providing in real-time, the axisymmetric measurements needed for plasma equilibrium reconstructions or magnetohydrodynamic instabilities control. In this paper, we present a fast and robust implementation on GPU architecture of an accurate algorithm suitable for the computation of synthetic magnetic measurements used both in real time applications and off-line reconstruction procedures. The proposed procedure is first applied to benchmark problems, to validate the compute unified device architecture implementation, and then to cases of practical interests in MCF.
- 2 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (6) , 1-4
A Volume Integral Formulation for Solving Eddy Current Problems on Polyhedral Meshes
This paper presents a volume integral formulation to solve eddy current problems on general polyhedral meshes. The required topological preprocessing is efficiently addressed in linear worst case complexity by using the idea of lazy cohomology generators.
- 2 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (6) , 1-4
A Volume Integral Formulation for Solving Eddy Current Problems on Polyhedral Meshes
This paper presents a volume integral formulation to solve eddy current problems on general polyhedral meshes. The required topological preprocessing is efficiently addressed in linear worst case complexity by using the idea of lazy cohomology generators.