Eduardo Ariel Ponzio
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Eduardo Ariel Ponzio has a total of 203 co-authors. Here are the top co-authors by number of shared publications:
- Caio Machado Fernandes
Universidade Federal do ABC Rua Santa Adélia 166 , Bairro Bangu
8 shared publications - Felipe Silva Semaan
Institute of Chemistry, Fluminense Federal University, Niterói, 24020-141, RJ, Brazil
8 shared publications - Juan Manuel Pardal
Universidade Federal Fluminense, Brasil
8 shared publications Marcelo T. G. de Sampaio
Laboratório de Materiais da UFF (G2E/LaMUFF), Instituto de Química, Universidade Federal Fluminense, Outeiro de São João Batista, s/n, Niterói, Rio de Janeiro, CEP 24020-141, Brazil
7 shared publicationsSergio S. M. Tavares
*****Programa de Pós-Graduação em Engenharia Mecânica e Montagem Industrial, Escola de Engenharia, Universidade Federal Fluminense, Rua Passo da Pátria, 156, Niterói, Rio de Janeriro, CEP 24210-240, Brazil
5 shared publications- Yutao Xing
Universidade Federal Fluminense
5 shared publications
Latest Publications
- 29 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (31) , 22657-22677
Electrochemical and Theoretical Evaluation of Carbothioamide-Derived Corrosion Inhibitors for Mild Steel in Acidic Environments
Organic inhibitors that couple strong heteroatom donor centers with tunable aromatic substituents are valuable platforms for clarifying structure-adsorption relationships in steel corrosion under acidic condition. Here, three 1H-1,2,3-triazol-4-yl carbothioamide derivatives bearing para-methoxy (MTCT), hydrogen (PTCT) or para-chloro (CTCT) substituents were synthesized and evaluated as inhibitors for mild steel in 1.0 mol L–1 HCl. Gravimetric tests at 298–338 K, electrochemical experiments, surface analysis, adsorption thermodynamics evaluation and DFT calculations were combined to relate macroscopic corrosion protection to molecular adsorption. All derivatives decreased the corrosion rate and suppressed both anodic, iron dissolution, and cathodic, hydrogen evolution, indicating mixed-type inhibition. At 1.0 mmol L–1 and 298 K, the inhibition efficiency followed CTCT > PTCT > MTCT, with CTCT reaching 94.1% by weight loss and 93.7% by EIS, with the same order maintained at higher temperatures. Increasing charge-transfer resistance and decreasing double-layer capacitance supported formation of an adsorbed protective layer, while Langmuir-type adsorption and negative Gibbs free energies indicated spontaneous adsorption with increasing chemisorptive contribution at elevated temperature. DFT-based descriptors, optimized Fe(110) adsorption geometries, and PDOS analyses showed that the superior performance of CTCT arises not simply from global electron-donating ability, but from a more favorable adsorption geometry, stronger molecule–surface interaction energy, and enhanced orbital hybridization with Fe states. These results identify triazole-carbothioamide derivatives as efficient acid corrosion inhibitors and clarify how subtle para-substitution modulates adsorption-controlled protection.
- 29 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (31) , 22657-22677
Electrochemical and Theoretical Evaluation of Carbothioamide-Derived Corrosion Inhibitors for Mild Steel in Acidic Environments
Organic inhibitors that couple strong heteroatom donor centers with tunable aromatic substituents are valuable platforms for clarifying structure-adsorption relationships in steel corrosion under acidic condition. Here, three 1H-1,2,3-triazol-4-yl carbothioamide derivatives bearing para-methoxy (MTCT), hydrogen (PTCT) or para-chloro (CTCT) substituents were synthesized and evaluated as inhibitors for mild steel in 1.0 mol L–1 HCl. Gravimetric tests at 298–338 K, electrochemical experiments, surface analysis, adsorption thermodynamics evaluation and DFT calculations were combined to relate macroscopic corrosion protection to molecular adsorption. All derivatives decreased the corrosion rate and suppressed both anodic, iron dissolution, and cathodic, hydrogen evolution, indicating mixed-type inhibition. At 1.0 mmol L–1 and 298 K, the inhibition efficiency followed CTCT > PTCT > MTCT, with CTCT reaching 94.1% by weight loss and 93.7% by EIS, with the same order maintained at higher temperatures. Increasing charge-transfer resistance and decreasing double-layer capacitance supported formation of an adsorbed protective layer, while Langmuir-type adsorption and negative Gibbs free energies indicated spontaneous adsorption with increasing chemisorptive contribution at elevated temperature. DFT-based descriptors, optimized Fe(110) adsorption geometries, and PDOS analyses showed that the superior performance of CTCT arises not simply from global electron-donating ability, but from a more favorable adsorption geometry, stronger molecule–surface interaction energy, and enhanced orbital hybridization with Fe states. These results identify triazole-carbothioamide derivatives as efficient acid corrosion inhibitors and clarify how subtle para-substitution modulates adsorption-controlled protection.
- 1 April 2025
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 81 (5) , 515-527
Influence of Excessive Nitrogen on Sensitization and Hardness of a Supermartensitic Stainless Steel
Supermartensitic stainless steel (SMSS) might be considered an advance in ordinary martensitic steel grade development, achieved by lowering carbon content and increasing key alloy elements such as nickel and molybdenum. Nitrogen may be added to improve mechanical resistance through a solid solution and, in specific cases, secondary hardening in the tempering treatment. Therefore, this work aims to investigate how the heat treatments might affect both the hardness and the degree of sensitization (DOS) of an SMSS type 13Cr-5Ni-2Mo with N microaddition (0.18%). In this regard, double loop electrochemical potentiokinetic reactivation tests were used to obtain the DOS, after which the surface of specimens was observed in the light optic microscope and scanning electron microscope. Thermo-Calc® analyses indicate several possible deleterious phases, and the x-ray diffraction measurements confirm low austenite content after 1 h of tempering. The results showed that this N-alloyed SMSS has higher DOS and hardness than the other 13Cr-5Ni-2Mo without nitrogen tempered in the 550°C to 600°C range. Finally, it was possible to correlate the DOS and hardness.
- 1 April 2025
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 81 (5) , 515-527
Influence of Excessive Nitrogen on Sensitization and Hardness of a Supermartensitic Stainless Steel
Supermartensitic stainless steel (SMSS) might be considered an advance in ordinary martensitic steel grade development, achieved by lowering carbon content and increasing key alloy elements such as nickel and molybdenum. Nitrogen may be added to improve mechanical resistance through a solid solution and, in specific cases, secondary hardening in the tempering treatment. Therefore, this work aims to investigate how the heat treatments might affect both the hardness and the degree of sensitization (DOS) of an SMSS type 13Cr-5Ni-2Mo with N microaddition (0.18%). In this regard, double loop electrochemical potentiokinetic reactivation tests were used to obtain the DOS, after which the surface of specimens was observed in the light optic microscope and scanning electron microscope. Thermo-Calc® analyses indicate several possible deleterious phases, and the x-ray diffraction measurements confirm low austenite content after 1 h of tempering. The results showed that this N-alloyed SMSS has higher DOS and hardness than the other 13Cr-5Ni-2Mo without nitrogen tempered in the 550°C to 600°C range. Finally, it was possible to correlate the DOS and hardness.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250248
Influence of Microstructure on the Corrosion Resistance of Low Carbon Uns S41003 Stainless Steel
The UNS S41003 (ASTM A1010) is a lean stainless steel with a chromium content of 10.5-11.0%. Its relatively low cost and enhanced corrosion resistance make it a promising alternative to carbon steels in various applications. Depending on the processing route the UNS S41003 with low carbon (<0.02%) and small Ni addition (~0.30%) may present ferritic, martensitic or ferritic-martensitic microstructures. In this work the corrosion resistance was evaluated in specimens processed by three different ways: hot rolling (HR), batch annealing (ANN), and water quenching from 1000ºC (Q). The microstructure of the HR is majoritarily martensitic, but also contains delta (δ) ferrite and fine dispersed carbides. The ANN specimen has equiaxial α ferritic grains with intergranular Cr carbides, and the quenched (Q) was martensitic. Polarization curves were carried out in 0.1M HCl solution. DL-EPR tests were also performed to evaluate the intergranular corrosion susceptibilities. It was observed that the martensitic microstructures have better corrosion than the annealed steel in polarization tests. which was highly susceptible to intergranular attack due to sensitization caused by intergranular Cr carbides.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250248
Open AccessInfluence of Microstructure on the Corrosion Resistance of Low Carbon Uns S41003 Stainless Steel
The UNS S41003 (ASTM A1010) is a lean stainless steel with a chromium content of 10.5-11.0%. Its relatively low cost and enhanced corrosion resistance make it a promising alternative to carbon steels in various applications. Depending on the processing route the UNS S41003 with low carbon (<0.02%) and small Ni addition (~0.30%) may present ferritic, martensitic or ferritic-martensitic microstructures. In this work the corrosion resistance was evaluated in specimens processed by three different ways: hot rolling (HR), batch annealing (ANN), and water quenching from 1000ºC (Q). The microstructure of the HR is majoritarily martensitic, but also contains delta (δ) ferrite and fine dispersed carbides. The ANN specimen has equiaxial α ferritic grains with intergranular Cr carbides, and the quenched (Q) was martensitic. Polarization curves were carried out in 0.1M HCl solution. DL-EPR tests were also performed to evaluate the intergranular corrosion susceptibilities. It was observed that the martensitic microstructures have better corrosion than the annealed steel in polarization tests. which was highly susceptible to intergranular attack due to sensitization caused by intergranular Cr carbides.
- 11 September 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (13) , 12494-12507
Quantification of Deleterious Phase Precipitation in a Hyper Duplex Stainless Steel Aged at 700-950 °C Using Optimized Linear Sweep Voltammetry: Effect of KOH Concentration
- 11 September 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (13) , 12494-12507
Quantification of Deleterious Phase Precipitation in a Hyper Duplex Stainless Steel Aged at 700-950 °C Using Optimized Linear Sweep Voltammetry: Effect of KOH Concentration
- Open Access
Solketal Production Using Eco-Friendly Reduced Graphene Oxide as the Catalyst
In this study, two materials based on reduced graphene oxide (rGOH or rGOE) were synthesized through the Hummers methodology and a more sustainable electrochemical method. These materials were extensively characterized and tested as catalysts in solketal production. Both rGOH and rGOE demonstrated significant catalytic activity, achieving 66.18% and 63.97% conversion rates, respectively. The catalytic activity of the synthesized materials was 30 times more efficient than the homogeneous catalyst p-Toluenesulfonic acid. Pseudo-homogeneous and heterogeneous kinetic models were employed to gain further insights into the glycerol ketalization reaction with acetone. The pseudo-homogeneous model suggested that the direct rate constant was lower than the reverse rate constant. In this sense, a reversible bimolecular reaction was proposed. The heterogeneous kinetic models revealed that in the Langmuir-Hinshelwood-Hougen-Watson mechanism, the controlling step of the reaction was the glycerol-acetone surface reaction on the catalyst. In contrast, in the Eley-Rideal mechanism, the reaction was controlled by the adsorbed glycerol on the reaction surface reacting with the available acetone in the bulk fluid. In the reusability tests, the rGOE catalyst demonstrated superior performance over five consecutive cycles, maintaining the highest activity without needing post-reaction washing or treatment.
Open AccessSolketal Production Using Eco-Friendly Reduced Graphene Oxide as the Catalyst
In this study, two materials based on reduced graphene oxide (rGOH or rGOE) were synthesized through the Hummers methodology and a more sustainable electrochemical method. These materials were extensively characterized and tested as catalysts in solketal production. Both rGOH and rGOE demonstrated significant catalytic activity, achieving 66.18% and 63.97% conversion rates, respectively. The catalytic activity of the synthesized materials was 30 times more efficient than the homogeneous catalyst p-Toluenesulfonic acid. Pseudo-homogeneous and heterogeneous kinetic models were employed to gain further insights into the glycerol ketalization reaction with acetone. The pseudo-homogeneous model suggested that the direct rate constant was lower than the reverse rate constant. In this sense, a reversible bimolecular reaction was proposed. The heterogeneous kinetic models revealed that in the Langmuir-Hinshelwood-Hougen-Watson mechanism, the controlling step of the reaction was the glycerol-acetone surface reaction on the catalyst. In contrast, in the Eley-Rideal mechanism, the reaction was controlled by the adsorbed glycerol on the reaction surface reacting with the available acetone in the bulk fluid. In the reusability tests, the rGOE catalyst demonstrated superior performance over five consecutive cycles, maintaining the highest activity without needing post-reaction washing or treatment.
- 15 August 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 51, 1460-1470
MagnetoElectroCatalysis: A new approach for urea electro-oxidation reaction on nickel-iron oxide catalyst
- 15 August 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 51, 1460-1470
MagnetoElectroCatalysis: A new approach for urea electro-oxidation reaction on nickel-iron oxide catalyst
- 6 October 2022
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 58 (1) , 1-11
DL-EPR vs. LSV-KOH: from simple detection of deleterious phases to analysis of morphology and high accuracy on determination of sigma phase in UNS S32750 stainless steel
An optimised electrochemical technique, linear sweep voltammetry (LSV) in KOH solution (LSV-KOH) was confronted with the double loop electrochemical Potentiokinetic reactivation (DL-EPR) to verify which is the best technique to quantify deleterious phases (DP) in a UNS S32750 super duplex stainless steel. DL-EPR presented an error in determination of deleterious phases in the range of 6.9–100%. LSV-KOH show a better accuracy in quantification of deleterious phases volume fractions, the error range for LSV-KOH was 2.4–26.2%. When the morphology of sigma changes from lamellar to divorced, was observed modifications on LSV-KOH voltammograms. In specimens where lamellar morphology is present, the voltammograms show two peaks curve. Meanwhile, in specimens where occurred also divorced precipitation of sigma the voltammograms changes to a 3 peaks curve. This feature is due to the dissolution of sigma phase boundaries which has different compositions according to the form of sigma precipitation.
- 6 October 2022
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 58 (1) , 1-11
DL-EPR vs. LSV-KOH: from simple detection of deleterious phases to analysis of morphology and high accuracy on determination of sigma phase in UNS S32750 stainless steel
An optimised electrochemical technique, linear sweep voltammetry (LSV) in KOH solution (LSV-KOH) was confronted with the double loop electrochemical Potentiokinetic reactivation (DL-EPR) to verify which is the best technique to quantify deleterious phases (DP) in a UNS S32750 super duplex stainless steel. DL-EPR presented an error in determination of deleterious phases in the range of 6.9–100%. LSV-KOH show a better accuracy in quantification of deleterious phases volume fractions, the error range for LSV-KOH was 2.4–26.2%. When the morphology of sigma changes from lamellar to divorced, was observed modifications on LSV-KOH voltammograms. In specimens where lamellar morphology is present, the voltammograms show two peaks curve. Meanwhile, in specimens where occurred also divorced precipitation of sigma the voltammograms changes to a 3 peaks curve. This feature is due to the dissolution of sigma phase boundaries which has different compositions according to the form of sigma precipitation.
- 19 July 2022
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 290
Corrosion inhibition and ecotoxicological assessment of 1,2,3-triazolic alcohols
- 19 July 2022
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 290
Corrosion inhibition and ecotoxicological assessment of 1,2,3-triazolic alcohols
- 25 January 2022
- Published by Wiley in Materials and Corrosion
- Vol. 73 (6) , 866-875
DL‐EPR and AFM study of sensitization of a 17%Cr multiphase stainless steel
The corrosion behavior of a 17Cr multiphase martensitic stainless steel quenched (1000°C, water cooling) and tempered at different temperatures was determined using the double‐loop electrochemical potentiokinetic reactivation (DL‐EPR) test. The specimen tempered at 550°C showed the highest degree of sensitization. For the specimen treated at 600°C, a healing process was observed, followed by a second sensitization at 625°C coincident with an increase in the austenite volume fraction. This phase was quantified using the magnetic method and an increase in this phase was observed with the tempering temperature. The DL‐EPR results were correlated with surface aspects obtained by atomic force microscopy.
- 25 January 2022
- Published by Wiley in Materials and Corrosion
- Vol. 73 (6) , 866-875
DL‐EPR and AFM study of sensitization of a 17%Cr multiphase stainless steel
The corrosion behavior of a 17Cr multiphase martensitic stainless steel quenched (1000°C, water cooling) and tempered at different temperatures was determined using the double‐loop electrochemical potentiokinetic reactivation (DL‐EPR) test. The specimen tempered at 550°C showed the highest degree of sensitization. For the specimen treated at 600°C, a healing process was observed, followed by a second sensitization at 625°C coincident with an increase in the austenite volume fraction. This phase was quantified using the magnetic method and an increase in this phase was observed with the tempering temperature. The DL‐EPR results were correlated with surface aspects obtained by atomic force microscopy.