Oh-Kyong Kwon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oh-Kyong Kwon has a total of 128 co-authors. Here are the top co-authors by number of shared publications:
- Seong-Kwan Hong
Hanyang University, Seoul, Republic of Korea
23 shared publications Seong-Kwan Hong
Dept. of Electronic Engineering Hanyang Univerity Seoul South Korea
9 shared publicationsSeong‐Kwan Hong
Hanyang University Seoul South Korea
7 shared publicationsHai-Jung In
Department of Electronic Engineering, Hanyang University, Seoul, Korea
5 shared publications- Jae-Sung An
Hanyang University, Seoul, South Korea
5 shared publications - Jaemyung Lim
Hanyang University
5 shared publications
Latest Publications
- 18 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 352-359
Low-Power, High-Performance, and Highly Reliable EM Gate Driver Circuit Using LTPO Technology for Mobile Displays
This article presents a compact, low-power, and high-performance pulsewidth-modulated (PWM) row driver circuit designed for high-resolution active-matrix organic light-emitting diode (AMOLED) displays, leveraging low-temperature polycrystalline silicon and oxide thin-film transistors (LTPO TFTs). The proposed 11T3C structure eliminates output intermediate voltage transitions and supports a wide range of variable refresh rates (VRRs) from 1 to 120 Hz, while minimizing both static and dynamic power consumption. A key innovation lies in the robust handling of oxide TFT threshold voltage variations using a bootstrapped control scheme that ensures stable turn-off behavior under stress-induced degradation. The proposed driver achieves fast transition times ( $1.01~\mu $ s rising and $1.56~\mu $ s falling) and maintains stable output across a 14 V swing, even under oxide ${V}_{\text {TH}}$ shifts from –7 to + 7 V. Power consumption was measured to be 4.35 mW at 1 Hz and 8.98 mW at 120 Hz for 1600 driver stages (3200 channels), demonstrating significant power reductions compared to conventional circuits. Full-panel measurements on a 6.81-in QHD AMOLED display demonstrate superior performance in terms of power and reliability compared to prior art, and were validated through industry-level qualification testing, supporting its suitability for ultralow-power displaysystems.
- 18 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 352-359
Low-Power, High-Performance, and Highly Reliable EM Gate Driver Circuit Using LTPO Technology for Mobile Displays
This article presents a compact, low-power, and high-performance pulsewidth-modulated (PWM) row driver circuit designed for high-resolution active-matrix organic light-emitting diode (AMOLED) displays, leveraging low-temperature polycrystalline silicon and oxide thin-film transistors (LTPO TFTs). The proposed 11T3C structure eliminates output intermediate voltage transitions and supports a wide range of variable refresh rates (VRRs) from 1 to 120 Hz, while minimizing both static and dynamic power consumption. A key innovation lies in the robust handling of oxide TFT threshold voltage variations using a bootstrapped control scheme that ensures stable turn-off behavior under stress-induced degradation. The proposed driver achieves fast transition times ( $1.01~\mu $ s rising and $1.56~\mu $ s falling) and maintains stable output across a 14 V swing, even under oxide ${V}_{\text {TH}}$ shifts from –7 to + 7 V. Power consumption was measured to be 4.35 mW at 1 Hz and 8.98 mW at 120 Hz for 1600 driver stages (3200 channels), demonstrating significant power reductions compared to conventional circuits. Full-panel measurements on a 6.81-in QHD AMOLED display demonstrate superior performance in terms of power and reliability compared to prior art, and were validated through industry-level qualification testing, supporting its suitability for ultralow-power displaysystems.
- 3 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (12) , 2285-2288
Highly Uniform and Flicker-Free Pixel Circuit for Wide Variable Refresh Rate AMOLED Displays
This letter proposes a 9T2C AMOLED pixel circuit that achieves high luminance uniformity and low flicker across a wide variable refresh rate (VRR) range of 15 to 360 Hz using LTPS TFTs. To enhance uniformity, the circuit compensates for threshold voltage (ΔVTH) and subthreshold slope (ΔSS) variations of the driving TFT by securing sufficient compensation time and employing a diode-connected current sink method. Flicker is significantly reduced by alleviating the effects of switching TFT leakage current, driving TFT hysteresis, and OLED parasitic capacitance (COLED) through a pulse-referenced method and maximum refresh rate (MRR) driving method. The circuit was fabricated on a 14-inch 4K AMOLED panel and experimentally verified. The measured worst-case spatial emission current errors (SECEs) were +2.8/-2.9 LSB and +0.4/-0.4 LSB at high and low gray levels, respectively. Regarding flicker, the worst temporal errors (TECEs) were measured to -1.7 LSB and +0.3 LSB at high and low gray levels, respectively.
- 3 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (12) , 2285-2288
Highly Uniform and Flicker-Free Pixel Circuit for Wide Variable Refresh Rate AMOLED Displays
This letter proposes a 9T2C AMOLED pixel circuit that achieves high luminance uniformity and low flicker across a wide variable refresh rate (VRR) range of 15 to 360 Hz using LTPS TFTs. To enhance uniformity, the circuit compensates for threshold voltage (ΔVTH) and subthreshold slope (ΔSS) variations of the driving TFT by securing sufficient compensation time and employing a diode-connected current sink method. Flicker is significantly reduced by alleviating the effects of switching TFT leakage current, driving TFT hysteresis, and OLED parasitic capacitance (COLED) through a pulse-referenced method and maximum refresh rate (MRR) driving method. The circuit was fabricated on a 14-inch 4K AMOLED panel and experimentally verified. The measured worst-case spatial emission current errors (SECEs) were +2.8/-2.9 LSB and +0.4/-0.4 LSB at high and low gray levels, respectively. Regarding flicker, the worst temporal errors (TECEs) were measured to -1.7 LSB and +0.3 LSB at high and low gray levels, respectively.
- 28 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (4) , 600-603
A Pixel Circuit With Improved Luminance Uniformity and Flicker for AMOLED Displays With a Wide VRR Range of 15 Hz to 360 Hz
This letter proposes a 6T2C pixel circuit designed for LTPS-based AMOLED displays to improve luminance uniformity and reduce flicker across a wide range of variable refresh rates (VRRs). The proposed circuit employs a two-step compensation method to address variations in the threshold voltage and subthreshold slope of driving thin-film transistors (TFTs), improving luminance uniformity. Additionally, it minimizes the hysteresis effect of TFTs using an inducing hole-trapping technique, resulting in lower flicker. The proposed pixel circuit was verified with 48 samples for a 5.8-inch QHD AMOLED display, achieving notable reductions in emission current errors (ECEs) within a VRR range of 15 Hz to 360 Hz. The luminance uniformity performance was improved compared to a previous 7T2C circuit, with measured spatial ECEs of +3.4/−3.4 LSB versus +4.1/−4.2 LSB at the 256th gray level. The flicker performance was also improved, with measured temporal ECEs of +0.4 LSB and −1.1 LSB versus −0.8 LSB and −3.2 LSB at the 16th and 256th gray levels, respectively.
- 28 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (4) , 600-603
A Pixel Circuit With Improved Luminance Uniformity and Flicker for AMOLED Displays With a Wide VRR Range of 15 Hz to 360 Hz
This letter proposes a 6T2C pixel circuit designed for LTPS-based AMOLED displays to improve luminance uniformity and reduce flicker across a wide range of variable refresh rates (VRRs). The proposed circuit employs a two-step compensation method to address variations in the threshold voltage and subthreshold slope of driving thin-film transistors (TFTs), improving luminance uniformity. Additionally, it minimizes the hysteresis effect of TFTs using an inducing hole-trapping technique, resulting in lower flicker. The proposed pixel circuit was verified with 48 samples for a 5.8-inch QHD AMOLED display, achieving notable reductions in emission current errors (ECEs) within a VRR range of 15 Hz to 360 Hz. The luminance uniformity performance was improved compared to a previous 7T2C circuit, with measured spatial ECEs of +3.4/−3.4 LSB versus +4.1/−4.2 LSB at the 256th gray level. The flicker performance was also improved, with measured temporal ECEs of +0.4 LSB and −1.1 LSB versus −0.8 LSB and −3.2 LSB at the 16th and 256th gray levels, respectively.
- Open Access
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 74301-74311
A Highly Uniform Luminance and Low-Flicker Pixel Circuit and Its Driving Methods for Variable Frame Rate AMOLED Displays
This paper proposes a 7T2C pixel circuit for active-matrix organic light-emitting diode (AMOLED) displays using low-temperature poly-crystalline silicon (LTPS) thin-film transistors (TFTs) with two key features: high luminance uniformity and low flicker at a wide range of variable frame rates (VFRs). To achieve a high luminance uniformity, the proposed pixel circuit simultaneously compensates for the threshold voltage variation and subthreshold slope variation of the driving TFT with a sufficient compensation time regardless of the frame rate. Furthermore, flicker is reduced by employing a ramping reference voltage and current blocking method, which reduces the effect of the leakage current of TFTs and OLED capacitance, respectively. Therefore, these techniques reduce spatial emission current errors (ECEs) and temporal ECEs, enabling the circuit to be used in the VFR from 15 Hz to 360 Hz. The proposed pixel circuit was verified with unit sub-pixels designed for a 14-inch 3840×2160 (4K) AMOLED display. The worst-case spatial ECEs of the proposed 7T2C pixel circuit at the frame rate of 360 Hz were measured as +4.1/-4.2 and +1.2/-1.1 LSB at the 255th and 15th gray levels, respectively. They show better luminance uniformity compared to those of the conventional 7T1C pixel circuit, which were measured as +6.1/-8.9 and +3.6/-3.6 LSB. Furthermore, the worst-case temporal ECEs at the frame rate of 15 Hz that shows flicker performance was measured as -0.3 and -3.2 LSB at the 15th and 255th gray levels, respectively, and they are better than those of the 7T1C pixel circuit, which show 11.2 and 2.41 LSB.
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 74301-74311
Open AccessA Highly Uniform Luminance and Low-Flicker Pixel Circuit and Its Driving Methods for Variable Frame Rate AMOLED Displays
This paper proposes a 7T2C pixel circuit for active-matrix organic light-emitting diode (AMOLED) displays using low-temperature poly-crystalline silicon (LTPS) thin-film transistors (TFTs) with two key features: high luminance uniformity and low flicker at a wide range of variable frame rates (VFRs). To achieve a high luminance uniformity, the proposed pixel circuit simultaneously compensates for the threshold voltage variation and subthreshold slope variation of the driving TFT with a sufficient compensation time regardless of the frame rate. Furthermore, flicker is reduced by employing a ramping reference voltage and current blocking method, which reduces the effect of the leakage current of TFTs and OLED capacitance, respectively. Therefore, these techniques reduce spatial emission current errors (ECEs) and temporal ECEs, enabling the circuit to be used in the VFR from 15 Hz to 360 Hz. The proposed pixel circuit was verified with unit sub-pixels designed for a 14-inch 3840×2160 (4K) AMOLED display. The worst-case spatial ECEs of the proposed 7T2C pixel circuit at the frame rate of 360 Hz were measured as +4.1/-4.2 and +1.2/-1.1 LSB at the 255th and 15th gray levels, respectively. They show better luminance uniformity compared to those of the conventional 7T1C pixel circuit, which were measured as +6.1/-8.9 and +3.6/-3.6 LSB. Furthermore, the worst-case temporal ECEs at the frame rate of 15 Hz that shows flicker performance was measured as -0.3 and -3.2 LSB at the 15th and 255th gray levels, respectively, and they are better than those of the 7T1C pixel circuit, which show 11.2 and 2.41 LSB.
- Open Access
- 30 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 119298-119309
A High Frame Rate Analog Front-End IC With Piezoelectric Micromachined Ultrasound Transducers Using Analog Multi-Line Acquisition for Ultrasound Imaging Systems
This paper proposes a high frame rate analog front-end (AFE) IC combined with a piezoelectric micromachined ultrasonic transducer (PMUT) for ultrasound imaging systems (UISs). The proposed AFE IC, which consists of 8-channel transceivers and a peripheral circuit, employs analog multi-line acquisition (AMLA) based on sub-array beamforming. This AMLA generates multiple scanlines during a scan time by simultaneously and precisely controlling the delay of the AFE IC, thus achieving the high frame rate of the AFE IC. The sensitivities of the PMUT for transmitting and receiving ultrasound waves are simulated to be 67.5 kPa/V and 1.2 mV/kPa, respectively, which are high enough to mitigate the needs of the high-voltage electronics for UISs. The proposed AFE IC was fabricated using a 0.18- $\mu \text{m}$ silicon-on-insulator process and occupies an active area of 2.56 mm $\times1.68$ mm. The measurement results using the simulated PMUT parameters show that the proposed AFE IC with the AMLA precisely controls its delay up to $1~\mu \text{s}$ at a clock frequency of 40 MHz. It also acquires more than 9,000 scan/s even at a focal depth of 150 mm, which is at least twice greater than those of prior works, achieving a high frame rate of 93 Hz when 100 scanlines are used for a frame. In addition, a figure-of-merit, which considers the energy consumption per channel/scan and the energy loss, is achieved to be 20 nJ/scan/dB at a focal depth of 150 mm and a center frequency of 3.6 MHz; this is the best result compared to previously reported works. Therefore, the proposed AFE IC is suitable for UISs requiring a high frame rate.
- 30 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 119298-119309
Open AccessA High Frame Rate Analog Front-End IC With Piezoelectric Micromachined Ultrasound Transducers Using Analog Multi-Line Acquisition for Ultrasound Imaging Systems
This paper proposes a high frame rate analog front-end (AFE) IC combined with a piezoelectric micromachined ultrasonic transducer (PMUT) for ultrasound imaging systems (UISs). The proposed AFE IC, which consists of 8-channel transceivers and a peripheral circuit, employs analog multi-line acquisition (AMLA) based on sub-array beamforming. This AMLA generates multiple scanlines during a scan time by simultaneously and precisely controlling the delay of the AFE IC, thus achieving the high frame rate of the AFE IC. The sensitivities of the PMUT for transmitting and receiving ultrasound waves are simulated to be 67.5 kPa/V and 1.2 mV/kPa, respectively, which are high enough to mitigate the needs of the high-voltage electronics for UISs. The proposed AFE IC was fabricated using a 0.18- $\mu \text{m}$ silicon-on-insulator process and occupies an active area of 2.56 mm $\times1.68$ mm. The measurement results using the simulated PMUT parameters show that the proposed AFE IC with the AMLA precisely controls its delay up to $1~\mu \text{s}$ at a clock frequency of 40 MHz. It also acquires more than 9,000 scan/s even at a focal depth of 150 mm, which is at least twice greater than those of prior works, achieving a high frame rate of 93 Hz when 100 scanlines are used for a frame. In addition, a figure-of-merit, which considers the energy consumption per channel/scan and the energy loss, is achieved to be 20 nJ/scan/dB at a focal depth of 150 mm and a center frequency of 3.6 MHz; this is the best result compared to previously reported works. Therefore, the proposed AFE IC is suitable for UISs requiring a high frame rate.
- 25 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (7) , 2322-2326
A High-Speed and Energy-Efficient Multi-Bit Cyclic ADC Using Single-Slope Quantizer for CMOS Image Sensors
This brief proposes a high-speed and power-efficient multi-bit cyclic analog-to-digital converter (MC ADC) for CMOS image sensor applications. The proposed 13-bit MC ADC, which uses a 4-bit single-slope (SS) quantizer as a sub-ADC, resolves the sampled input voltage, followed by the cyclic SS quantization operation that repeatedly produces and quantizes the residue voltage. It operates in only seven phases to resolve 13-bit, thus achieving high conversion speed. Moreover, the 4-bit SS quantizer employs a simple and power-efficient structure that includes only the analog circuits of an operational amplifier and a comparator. A test chip with the proposed MC ADC was fabricated using a 0.18-μm standard CMOS process technology. The measurement results show that the proposed MC ADC achieves a differential nonlinearity of +0.5/–0.54 LSB and an integral nonlinearity of +1.7/–2.8 LSB. In addition, the maximum signal-to-noise-and-distortion ratio and the effective number of bits are measured to be 73.14 dB and 11.86-bit, respectively. The measured power consumption per channel is only 87 μW at a sampling frequency of 781 kHz. Moreover, the figure of merit (FoM), which includes the power consumption per channel, row line time, and ADC resolution, is only 13.6 fJ/conversion, achieving the best FoM among the compared works. Therefore, the proposed MC ADC is suitable for CMOS image sensor applications requiring high conversion speed and low power consumption, such as digital single-lens reflex cameras and ultra-high-definition television broadcast cameras.
- 25 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (7) , 2322-2326
A High-Speed and Energy-Efficient Multi-Bit Cyclic ADC Using Single-Slope Quantizer for CMOS Image Sensors
This brief proposes a high-speed and power-efficient multi-bit cyclic analog-to-digital converter (MC ADC) for CMOS image sensor applications. The proposed 13-bit MC ADC, which uses a 4-bit single-slope (SS) quantizer as a sub-ADC, resolves the sampled input voltage, followed by the cyclic SS quantization operation that repeatedly produces and quantizes the residue voltage. It operates in only seven phases to resolve 13-bit, thus achieving high conversion speed. Moreover, the 4-bit SS quantizer employs a simple and power-efficient structure that includes only the analog circuits of an operational amplifier and a comparator. A test chip with the proposed MC ADC was fabricated using a 0.18-μm standard CMOS process technology. The measurement results show that the proposed MC ADC achieves a differential nonlinearity of +0.5/–0.54 LSB and an integral nonlinearity of +1.7/–2.8 LSB. In addition, the maximum signal-to-noise-and-distortion ratio and the effective number of bits are measured to be 73.14 dB and 11.86-bit, respectively. The measured power consumption per channel is only 87 μW at a sampling frequency of 781 kHz. Moreover, the figure of merit (FoM), which includes the power consumption per channel, row line time, and ADC resolution, is only 13.6 fJ/conversion, achieving the best FoM among the compared works. Therefore, the proposed MC ADC is suitable for CMOS image sensor applications requiring high conversion speed and low power consumption, such as digital single-lens reflex cameras and ultra-high-definition television broadcast cameras.
- Open Access
- 2 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 162172-162179
A Highly Reliable SIMO Converter Using Hybrid Starter and Overcharging Protector for Energy Harvesting Systems
This paper proposes a highly reliable single-inductor multi-output (SIMO) converter for energy harvesting systems, which is controlled by the power management controller (PMC) including the hybrid starter, overcharging protector (OCP), and switch controller (SWC). The proposed hybrid starter employs the power-on-reset to accurately control the activated and deactivated moments of the SWC, thus generating a system supply voltage (VSYS) within the stable operating voltage range. The proposed OCP employs the diode-connection and Schmitt trigger schemes to monitor the voltage of a storage device (VSTG) in real time, thereby protecting the IC from being damaged without using either a capacitor or Zener diode, which causes the additional area or reverse leakage current, respectively. The proposed SIMO converter with the PMC was fabricated using 0.18-μm CMOS process. The measurement results show that VSYS values at the activated and deactivated moments of the SWC are 1.798 V and 1.510 V, respectively, both of which are within the stable system voltage range for 1.8 V devices. In addition, the measured maximum VSTG is 5.892 V, which is much lower than an absolute maximum rated voltage of 9.2 V for 5 V devices. Furthermore, the measurement results reveal that the hybrid starter allows the proposed SIMO converter to be properly restarted immediately after VSYS is shorted to ground, while the OCP safely protects the SIMO converter even when the storage device is removed from the IC while charging. Therefore, the proposed SIMO converter with the PMC is suitable for energy harvesting systems that require high reliability.
- 2 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 162172-162179
Open AccessA Highly Reliable SIMO Converter Using Hybrid Starter and Overcharging Protector for Energy Harvesting Systems
This paper proposes a highly reliable single-inductor multi-output (SIMO) converter for energy harvesting systems, which is controlled by the power management controller (PMC) including the hybrid starter, overcharging protector (OCP), and switch controller (SWC). The proposed hybrid starter employs the power-on-reset to accurately control the activated and deactivated moments of the SWC, thus generating a system supply voltage (VSYS) within the stable operating voltage range. The proposed OCP employs the diode-connection and Schmitt trigger schemes to monitor the voltage of a storage device (VSTG) in real time, thereby protecting the IC from being damaged without using either a capacitor or Zener diode, which causes the additional area or reverse leakage current, respectively. The proposed SIMO converter with the PMC was fabricated using 0.18-μm CMOS process. The measurement results show that VSYS values at the activated and deactivated moments of the SWC are 1.798 V and 1.510 V, respectively, both of which are within the stable system voltage range for 1.8 V devices. In addition, the measured maximum VSTG is 5.892 V, which is much lower than an absolute maximum rated voltage of 9.2 V for 5 V devices. Furthermore, the measurement results reveal that the hybrid starter allows the proposed SIMO converter to be properly restarted immediately after VSYS is shorted to ground, while the OCP safely protects the SIMO converter even when the storage device is removed from the IC while charging. Therefore, the proposed SIMO converter with the PMC is suitable for energy harvesting systems that require high reliability.
- 21 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (11) , 3087-3096
An AMOLED Pixel Circuit With a Compensating Scheme for Variations in Subthreshold Slope and Threshold Voltage of Driving TFTs
This article proposes an active-matrix organic light-emitting diode (AMOLED) pixel circuit for mobile displays with high resolution to improve the image quality of the display panel. The proposed pixel circuit, which consists of six low-temperature polycrystalline silicon thin-film transistors (TFTs) and two capacitors, compensates for variations in the threshold voltage (Vth) and subthreshold slope (SS) of driving TFTs at low gray levels. Such compensations are achieved by extending the compensation time in the diode-connection scheme, resulting in a reduction in the OLED current error (OCE) of the proposed pixel circuit. In addition, the proposed pixel circuit connects two capacitors in parallel to the gate node of the driving TFT, thus increasing the total storage capacitance value in a given capacitor area in the emission phase, resulting in a reduction in voltage distortion at the gate node. Moreover, the OCEs caused by the IR drop of ELVDD and the crosstalk due to parasitic capacitances are thoroughly investigated and analyzed. The measurement results of the proposed pixel circuit show that the OCEs at the 64th and 128th gray levels are reduced from ±3.5 and ±6.5 to ±2.0 and ±0.8 LSB, respectively, by extending the compensation time from 6.5 to 195 μs. Therefore, the proposed pixel circuit is highly suitable for mobile AMOLED displays requiring high image quality.
- 21 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (11) , 3087-3096
An AMOLED Pixel Circuit With a Compensating Scheme for Variations in Subthreshold Slope and Threshold Voltage of Driving TFTs
This article proposes an active-matrix organic light-emitting diode (AMOLED) pixel circuit for mobile displays with high resolution to improve the image quality of the display panel. The proposed pixel circuit, which consists of six low-temperature polycrystalline silicon thin-film transistors (TFTs) and two capacitors, compensates for variations in the threshold voltage (Vth) and subthreshold slope (SS) of driving TFTs at low gray levels. Such compensations are achieved by extending the compensation time in the diode-connection scheme, resulting in a reduction in the OLED current error (OCE) of the proposed pixel circuit. In addition, the proposed pixel circuit connects two capacitors in parallel to the gate node of the driving TFT, thus increasing the total storage capacitance value in a given capacitor area in the emission phase, resulting in a reduction in voltage distortion at the gate node. Moreover, the OCEs caused by the IR drop of ELVDD and the crosstalk due to parasitic capacitances are thoroughly investigated and analyzed. The measurement results of the proposed pixel circuit show that the OCEs at the 64th and 128th gray levels are reduced from ±3.5 and ±6.5 to ±2.0 and ±0.8 LSB, respectively, by extending the compensation time from 6.5 to 195 μs. Therefore, the proposed pixel circuit is highly suitable for mobile AMOLED displays requiring high image quality.