Finbarr Gerard O'NEill
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Finbarr Gerard O'NEill has a total of 114 co-authors. Here are the top co-authors by number of shared publications:
- Antonello Sala
Institute for Marine Biological Resources and Biotechnology, National Research Council (CNR-IRBIM), Ancona, Italy
4 shared publications A. Ivanović
3 shared publicationsAna Ivanović
School of Engineering, Fraser Noble Building , University of Aberdeen , Aberdeen AB24 3UE , UK
3 shared publications- Bent Herrmann
SINTEF Ocean, Fishing Gear Technology, Willemoesvej 2, 9850 Hirtshals, Denmark
3 shared publications K. Summerbell
3 shared publicationsKeith Summerbell
Marine Scotland-Science , PO Box 101, 375 Victoria Road, Aberdeen AB11 9DB , UK
3 shared publications
Latest Publications
- Open Access
- 2 July 2025
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (7)
A gear component approach to trawling impact and sediment mobilization assessments
Increased awareness of the impacts of bottom trawling has led to the development of various methods to assess the extent and impact of trawling-induced seabed abrasion. These methods typically classify bottom trawls into broad categories and rely on whole-gear averages to evaluate their spatial distribution and seabed impacts. However, such approaches overlook variations in gear design within fisheries and are unable to capture changes resulting from gear innovations. Here, we present a Gear Component Approach (GCA), which, using data from literature and industry-surveys, considers the individual contribution of each seabed-contacting gear component (doors, clumps, sweeps, and ground gear) within a fishery. We demonstrate the GCA’s ability to assess the extent and impact of three Danish otter trawl fisheries and compare these results with those obtained using the currently practiced Whole-Gear Approach (WGA). The GCA produced different estimates of gear width and penetration depth compared to WGA estimates. This led to lower predictions of the relative benthic state (RBS) indicator, which represents the proportion of the original benthic community biomass remaining under a given fishing pressure. These results imply higher fishing impacts for all three otter trawl fisheries compared to the WGA estimates. The difference was most pronounced for the Nephrops fishery, where the RBS indicator was 23% lower. Additionally, the GCA enabled the quantification of sediment mobilization, with up to 3.2 kg per m2 swept by the Nephrops trawl. The GCA improved the representativeness of fishing gear and the accuracy of impact assessments, thereby supporting sustainable marine fisheries management. Moreover, owing to its focus at the gear-component level, the GCA facilitates the evaluation of innovative gear modifications aimed at reducing seabed impact.
- 2 July 2025
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (7)
Open AccessA gear component approach to trawling impact and sediment mobilization assessments
Increased awareness of the impacts of bottom trawling has led to the development of various methods to assess the extent and impact of trawling-induced seabed abrasion. These methods typically classify bottom trawls into broad categories and rely on whole-gear averages to evaluate their spatial distribution and seabed impacts. However, such approaches overlook variations in gear design within fisheries and are unable to capture changes resulting from gear innovations. Here, we present a Gear Component Approach (GCA), which, using data from literature and industry-surveys, considers the individual contribution of each seabed-contacting gear component (doors, clumps, sweeps, and ground gear) within a fishery. We demonstrate the GCA’s ability to assess the extent and impact of three Danish otter trawl fisheries and compare these results with those obtained using the currently practiced Whole-Gear Approach (WGA). The GCA produced different estimates of gear width and penetration depth compared to WGA estimates. This led to lower predictions of the relative benthic state (RBS) indicator, which represents the proportion of the original benthic community biomass remaining under a given fishing pressure. These results imply higher fishing impacts for all three otter trawl fisheries compared to the WGA estimates. The difference was most pronounced for the Nephrops fishery, where the RBS indicator was 23% lower. Additionally, the GCA enabled the quantification of sediment mobilization, with up to 3.2 kg per m2 swept by the Nephrops trawl. The GCA improved the representativeness of fishing gear and the accuracy of impact assessments, thereby supporting sustainable marine fisheries management. Moreover, owing to its focus at the gear-component level, the GCA facilitates the evaluation of innovative gear modifications aimed at reducing seabed impact.
- 1 January 2025
- Published by Canadian Science Publishing in Canadian Journal of Fisheries and Aquatic Sciences
- Vol. 82, 1-16
Enhancing bycatch escape in trawl fisheries through flow manipulation: a study on Gadoids
Flow manipulation offers a promising yet under-utilized method for enhancing bycatch escape in demersal trawl fisheries by exploiting fish swimming behaviors, such as flow refuging. We investigated to what extent different Gadoids use a low-flow zone to escape from a trawl. A 360° radial escape opportunity was created by placing a gap in the codend within the low-flow zone generated by a tarpaulin funnel. An additional tarpaulin deflector expanded the low-flow zone to prevent fish from holding around the funnel. This proof-of-concept design was developed using flume tank trials and computational fluid dynamics, and tested at sea. Substantial escape rates were observed for cod ( Gadus morhua), haddock ( Melanogrammus aeglefinus), and whiting ( Merlangius merlangus). Cod showed an increased escape rate with length, while no such trend was seen in haddock or whiting. We tested two gap sizes and found that a shorter gap size resulted in higher escape rates for undersized haddock and whiting, while cod escape was unaffected by gap size. These findings suggest species-specific interactions between hydrodynamics and behavior, useful for bycatch reduction in trawl fisheries.
- 1 January 2025
- Published by Canadian Science Publishing in Canadian Journal of Fisheries and Aquatic Sciences
- Vol. 82, 1-16
Enhancing bycatch escape in trawl fisheries through flow manipulation: a study on Gadoids
Flow manipulation offers a promising yet under-utilized method for enhancing bycatch escape in demersal trawl fisheries by exploiting fish swimming behaviors, such as flow refuging. We investigated to what extent different Gadoids use a low-flow zone to escape from a trawl. A 360° radial escape opportunity was created by placing a gap in the codend within the low-flow zone generated by a tarpaulin funnel. An additional tarpaulin deflector expanded the low-flow zone to prevent fish from holding around the funnel. This proof-of-concept design was developed using flume tank trials and computational fluid dynamics, and tested at sea. Substantial escape rates were observed for cod ( Gadus morhua), haddock ( Melanogrammus aeglefinus), and whiting ( Merlangius merlangus). Cod showed an increased escape rate with length, while no such trend was seen in haddock or whiting. We tested two gap sizes and found that a shorter gap size resulted in higher escape rates for undersized haddock and whiting, while cod escape was unaffected by gap size. These findings suggest species-specific interactions between hydrodynamics and behavior, useful for bycatch reduction in trawl fisheries.
- Open Access
- 7 November 2024
- Published by Elsevier in Marine Pollution Bulletin
- Vol. 209 (Pt B) , 117229
Sediment penetration by towed, seabed-contacting, fishing gear components
- 7 November 2024
- Published by Elsevier in Marine Pollution Bulletin
- Vol. 209 (Pt B) , 117229
Open AccessSediment penetration by towed, seabed-contacting, fishing gear components
- 1 April 2024
- Published by Canadian Science Publishing in Canadian Journal of Fisheries and Aquatic Sciences
- Vol. 81 (4) , 444-458
Semi-pelagic self-adjusting otter boards: effects on the catching performance of a demersal trawl
In this study, we investigate whether replacing conventional seabed-contacting otter boards with semi-pelagic self-adjusting otter (SAO) boards, which have the ability to maintain a given height above the seabed, affects the catch efficiency of a demersal fish trawl. Experimental fishing trials, using the alternate haul method, were conducted in the Kattegat and Skagerrak with three otter board configurations using conventional seabed-contacting otter boards; the SAO set to maintain a target height over the seabed of 1 m; and the SAO set to maintain a target height of 5 m. Replacing conventional otter boards with SAO resulted in a loss of catch efficiency for haddock ( Melanogrammus aeglefinus), whiting ( Merlangius merlangus), and plaice ( Hippoglossoides platessoides), while no significant difference was found for cod ( Gadus morhua), common dab ( Limanda limanda), and lemon sole ( Microstomus kitt). When comparing the SAO-1 m and SAO-5 m, it was observed that SAO-5 m resulted in a loss of catch efficiency for haddock and plaice, a minimal reduction for cod, and no significant difference for whiting, common dab, and lemon sole.
- 1 April 2024
- Published by Canadian Science Publishing in Canadian Journal of Fisheries and Aquatic Sciences
- Vol. 81 (4) , 444-458
Semi-pelagic self-adjusting otter boards: effects on the catching performance of a demersal trawl
In this study, we investigate whether replacing conventional seabed-contacting otter boards with semi-pelagic self-adjusting otter (SAO) boards, which have the ability to maintain a given height above the seabed, affects the catch efficiency of a demersal fish trawl. Experimental fishing trials, using the alternate haul method, were conducted in the Kattegat and Skagerrak with three otter board configurations using conventional seabed-contacting otter boards; the SAO set to maintain a target height over the seabed of 1 m; and the SAO set to maintain a target height of 5 m. Replacing conventional otter boards with SAO resulted in a loss of catch efficiency for haddock ( Melanogrammus aeglefinus), whiting ( Merlangius merlangus), and plaice ( Hippoglossoides platessoides), while no significant difference was found for cod ( Gadus morhua), common dab ( Limanda limanda), and lemon sole ( Microstomus kitt). When comparing the SAO-1 m and SAO-5 m, it was observed that SAO-5 m resulted in a loss of catch efficiency for haddock and plaice, a minimal reduction for cod, and no significant difference for whiting, common dab, and lemon sole.
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 76
USING HYDRODYNAMICS TO IMPROVE SEA STAR FISHERIES IN COASTAL REGIONS
Sea stars (starfish) predate on various shellfish such as mussels and clams, and can have a negative impact on the blue-mussel production and aquaculture. This has encouraged the harvesting of sea stars to protect blue mussels and clams from predation, but they are also targeted commercially, as a valuable protein source used e.g. in animal feed. Towed fishing gears can be used to harvest sea stars in coastal regions, however, little is known scientifically about the hydrodynamics around these gears. To better understand the hydrodynamics around towed fishing gears, an experimental investigation has been carried out in a current flume within the DTU Civil and Mechanical Engineering Hydraulics Laboratory.
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 76
Open AccessUSING HYDRODYNAMICS TO IMPROVE SEA STAR FISHERIES IN COASTAL REGIONS
Sea stars (starfish) predate on various shellfish such as mussels and clams, and can have a negative impact on the blue-mussel production and aquaculture. This has encouraged the harvesting of sea stars to protect blue mussels and clams from predation, but they are also targeted commercially, as a valuable protein source used e.g. in animal feed. Towed fishing gears can be used to harvest sea stars in coastal regions, however, little is known scientifically about the hydrodynamics around these gears. To better understand the hydrodynamics around towed fishing gears, an experimental investigation has been carried out in a current flume within the DTU Civil and Mechanical Engineering Hydraulics Laboratory.
- Open Access
- 31 January 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (2) , 296
Morphology and Settling Velocity of Sea Stars (Asterias rubens)
This study presents morphological data and estimates of the settling velocity and drag coefficient of sea stars (Asterias rubens) caught in the Limfjord, Denmark. A geometric model describing the sea star is presented and the thickness and arm width are determined as linear functions of arm length. The volume and mass of the sea stars is well predicted by the geometric model and is in agreement with the experimental measurements. The mean sea star density is determined to be 1095 kg/m3, the mean drag coefficient is estimated to be 2.3 and the settling velocity is shown to vary with the square root of the its size.
- 31 January 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (2) , 296
Open AccessMorphology and Settling Velocity of Sea Stars (Asterias rubens)
This study presents morphological data and estimates of the settling velocity and drag coefficient of sea stars (Asterias rubens) caught in the Limfjord, Denmark. A geometric model describing the sea star is presented and the thickness and arm width are determined as linear functions of arm length. The volume and mass of the sea stars is well predicted by the geometric model and is in agreement with the experimental measurements. The mean sea star density is determined to be 1095 kg/m3, the mean drag coefficient is estimated to be 2.3 and the settling velocity is shown to vary with the square root of the its size.
- Open Access
- 1 July 2020
- Published by Elsevier in Fisheries Research
- Vol. 227
A meta-analysis of plaice size-selection data in otter trawl codends
- 1 July 2020
- Published by Elsevier in Fisheries Research
- Vol. 227
Open AccessA meta-analysis of plaice size-selection data in otter trawl codends
- Open Access
- 11 March 2020
- Published by Wiley in Fish and Fisheries
- Vol. 21 (3) , 621-638
Selectivity metrics for fisheries management and advice
Fisheries management typically aims at controlling exploitation rate (e.g., Fbar) to ensure sustainable levels of stock size in accordance with established reference points (e.g., FMSY, BMSY). Population selectivity (“selectivity” hereafter), that is the distribution of fishing mortality over the different demographic components of an exploited fish stock, is also important because it affects both Maximum Sustainable Yield (MSY) and FMSY, as well as stock resilience to overfishing. The development of an appropriate metric could make selectivity operational as an additional lever for fisheries managers to achieve desirable outcomes. Additionally, such a selectivity metric could inform managers on the uptake by fleets and effects on stocks of various technical measures. Here, we introduce three criteria for selectivity metrics: (a) sensitivity to selectivity changes, (b) robustness to recruitment variability and (c) robustness to changes in Fbar. Subsequently, we test a range of different selectivity metrics against these three criteria to identify the optimal metric. First, we simulate changes in selectivity, recruitment and Fbar on a virtual fish stock to study the metrics under controlled conditions. We then apply two shortlisted selectivity metrics to six European fish stocks with a known history of technical measures to explore the metrics’ response in real‐world situations. This process identified the ratio of F of the first recruited age–class to Fbar (Frec/Fbar) as an informative selectivity metric for fisheries management and advice.
- 11 March 2020
- Published by Wiley in Fish and Fisheries
- Vol. 21 (3) , 621-638
Open AccessSelectivity metrics for fisheries management and advice
Fisheries management typically aims at controlling exploitation rate (e.g., Fbar) to ensure sustainable levels of stock size in accordance with established reference points (e.g., FMSY, BMSY). Population selectivity (“selectivity” hereafter), that is the distribution of fishing mortality over the different demographic components of an exploited fish stock, is also important because it affects both Maximum Sustainable Yield (MSY) and FMSY, as well as stock resilience to overfishing. The development of an appropriate metric could make selectivity operational as an additional lever for fisheries managers to achieve desirable outcomes. Additionally, such a selectivity metric could inform managers on the uptake by fleets and effects on stocks of various technical measures. Here, we introduce three criteria for selectivity metrics: (a) sensitivity to selectivity changes, (b) robustness to recruitment variability and (c) robustness to changes in Fbar. Subsequently, we test a range of different selectivity metrics against these three criteria to identify the optimal metric. First, we simulate changes in selectivity, recruitment and Fbar on a virtual fish stock to study the metrics under controlled conditions. We then apply two shortlisted selectivity metrics to six European fish stocks with a known history of technical measures to explore the metrics’ response in real‐world situations. This process identified the ratio of F of the first recruited age–class to Fbar (Frec/Fbar) as an informative selectivity metric for fisheries management and advice.
- Open Access
- 20 December 2018
- Published by Springer Nature
- p. 279-296
Discard Avoidance by Improving Fishing Gear Selectivity: Helping the Fishing Industry Help Itself
- 20 December 2018
- Published by Springer Nature
- p. 279-296
Open AccessDiscard Avoidance by Improving Fishing Gear Selectivity: Helping the Fishing Industry Help Itself
- Open Access
- 1 January 2018
- Published by Elsevier in Journal of Marine Systems
- Vol. 177, 39-52
The contact drag of towed demersal fishing gear components
- 1 January 2018
- Published by Elsevier in Journal of Marine Systems
- Vol. 177, 39-52
Open AccessThe contact drag of towed demersal fishing gear components