Rastislav Lagaňa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rastislav Lagaňa has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
- Jaroslav Ďurkovič
Department of Phytology, Technical University in Zvolen, 960 01 Zvolen, Slovakia
9 shared publications Ingrid Čaňová
Technical University in Zvolen, T.G. Masaryka 24, 960 53 Zvolen, Slovak Republic
5 shared publicationsMonika Kardošová
Faculty of Forestry, Technical University in Zvolen, 96001 Zvolen, Slovakia
5 shared publications- František Kačík
Department of Chemistry and Chemical Technology, Faculty of Wood Sciences and Technology, Technical University in Zvolen, 96001 Zvolen, Slovakia, Slovakia
4 shared publications - Nadežda Langová
Department of Furniture and Wood Products, Faculty of Wood Sciences and Technology, Technical University in Zvolen, T. G. Masaryka 24, 960 01 Zvolen, Slovakia
3 shared publications Tibor Priwitzer
3 shared publications
Latest Publications
- Open Access
Stiffness-Based Grading of Thermally Modified Beech Timber for Structural Applications
Thermally modified wood is primarily used in exterior applications due to its enhanced resistance to biotic degradation. However, reduced mechanical performance limits its structural use. This study investigates the structural potential of high-temperature-treated European beech timber (Fagus sylvatica, L.) and evaluates its mechanical properties and grading models for structural design. Timber from 32 beech logs was air-dried and divided into untreated (NoTMW) and thermally modified (TMW) groups. Thermal modification was carried out commercially in an oxidizing atmosphere at 190 °C. All specimens were visually graded according to DIN 4074-5 and assessed using acoustic non-destructive methods before testing in four-point bending following EN 408. Modulus of elasticity (MOE), modulus of rupture (MOR), and density were determined, and characteristic values were calculated according to EN 384. On average, TMW exhibited a 17% reduction in bending strength compared to untreated wood, while both static and dynamic MOE were not significantly affected. The multiple regression model only slightly improved bending strength prediction compared with single linear regression based on global modulus, as the R2-value increased from 17% to 19%. The prediction of stiffness of thermally treated beech timber was greatly improved by combining local and acoustic moduli, explaining 76% of the total variation.
Open AccessStiffness-Based Grading of Thermally Modified Beech Timber for Structural Applications
Thermally modified wood is primarily used in exterior applications due to its enhanced resistance to biotic degradation. However, reduced mechanical performance limits its structural use. This study investigates the structural potential of high-temperature-treated European beech timber (Fagus sylvatica, L.) and evaluates its mechanical properties and grading models for structural design. Timber from 32 beech logs was air-dried and divided into untreated (NoTMW) and thermally modified (TMW) groups. Thermal modification was carried out commercially in an oxidizing atmosphere at 190 °C. All specimens were visually graded according to DIN 4074-5 and assessed using acoustic non-destructive methods before testing in four-point bending following EN 408. Modulus of elasticity (MOE), modulus of rupture (MOR), and density were determined, and characteristic values were calculated according to EN 384. On average, TMW exhibited a 17% reduction in bending strength compared to untreated wood, while both static and dynamic MOE were not significantly affected. The multiple regression model only slightly improved bending strength prediction compared with single linear regression based on global modulus, as the R2-value increased from 17% to 19%. The prediction of stiffness of thermally treated beech timber was greatly improved by combining local and acoustic moduli, explaining 76% of the total variation.
- Open Access
- 28 December 2025
- Published by MDPI AG in Biomimetics
- Vol. 11 (1) , 15
Biomimetic Assessment of 3D-Printed T-Shape Joints Bio-Inspired by the Stem-Branch Junction in Common Ash (Fraxinus excelsior L.) Trees
The stem–branch junction in trees demonstrates exceptional structural design. This study examined two key features of the branch junction in common ash (Fraxinus excelsior L.) wood: the interlocked area (ILA) formed above a knot and the spatial arrangement of fibers in the junction. Bio-inspired by the microstructural features revealed by micro-computed tomography imaging, we developed 3D-printed models and compared their mechanical performance to standard symmetrical T-joints. We evaluated the models using mechanical tests and finite element modeling (FEM). Asymmetrical 3D-printed joints mimicking vessel and fiber distribution in the stem–branch junction were 2% stiffer in the elastic region than symmetrical joints and showed, on average, 10% lower deflection at failure. While the ILA had minimal effect on elastic stiffness, measured surface strain analysis indicated that it positively influenced the redistribution of shear strain in the junctions. Thanks to the bio-inspired design, the joints were stiffer and can be utilized in multiple design configurations while maintaining the same underlying principle.
- 28 December 2025
- Published by MDPI AG in Biomimetics
- Vol. 11 (1) , 15
Open AccessBiomimetic Assessment of 3D-Printed T-Shape Joints Bio-Inspired by the Stem-Branch Junction in Common Ash (Fraxinus excelsior L.) Trees
The stem–branch junction in trees demonstrates exceptional structural design. This study examined two key features of the branch junction in common ash (Fraxinus excelsior L.) wood: the interlocked area (ILA) formed above a knot and the spatial arrangement of fibers in the junction. Bio-inspired by the microstructural features revealed by micro-computed tomography imaging, we developed 3D-printed models and compared their mechanical performance to standard symmetrical T-joints. We evaluated the models using mechanical tests and finite element modeling (FEM). Asymmetrical 3D-printed joints mimicking vessel and fiber distribution in the stem–branch junction were 2% stiffer in the elastic region than symmetrical joints and showed, on average, 10% lower deflection at failure. While the ILA had minimal effect on elastic stiffness, measured surface strain analysis indicated that it positively influenced the redistribution of shear strain in the junctions. Thanks to the bio-inspired design, the joints were stiffer and can be utilized in multiple design configurations while maintaining the same underlying principle.
- 11 July 2025
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
Improving the stiffness of the corner connections in wooden door frames
The research aimed to determine the strength and stiffness of corner joints in interior door frames, depending on their construction and the modifications made to the design of the door frame joints. Initially, two models were compared: model 1, with two connectors using a clamping screw at an angle of 45°, and model 0, with a single connector using a cam joint at an angle of 90°. In all tests, model 1 exhibited significantly better mechanical properties. To improve the performance of model 0, three alternative construction models (A, B, and C) were proposed by changing the position of the door frame mounting holes. In the compression test, model A showed an increased bending moment compared to model 0, while models B and C showed no such improvement. In the tension test, the bending moment values remained at a similar level across all construction variants, including model 0. In terms of bending moment, the best result in compression was achieved by model A (48.26 Nm), and in tension by model B (48.72 Nm). The highest stiffness was demonstrated by model 1 (up to 42.38 kNm/rad), while among the alternative models, model C showed the best result in tension (33.98 kNm/rad). Due to the favourable increase in bending moment under compression in model A and the insignificant changes under tension across all variants, model A is considered the optimal solution. To enhance the strength of the door frame, offset holes can be applied as proposed in this model.
- 11 July 2025
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
Improving the stiffness of the corner connections in wooden door frames
The research aimed to determine the strength and stiffness of corner joints in interior door frames, depending on their construction and the modifications made to the design of the door frame joints. Initially, two models were compared: model 1, with two connectors using a clamping screw at an angle of 45°, and model 0, with a single connector using a cam joint at an angle of 90°. In all tests, model 1 exhibited significantly better mechanical properties. To improve the performance of model 0, three alternative construction models (A, B, and C) were proposed by changing the position of the door frame mounting holes. In the compression test, model A showed an increased bending moment compared to model 0, while models B and C showed no such improvement. In the tension test, the bending moment values remained at a similar level across all construction variants, including model 0. In terms of bending moment, the best result in compression was achieved by model A (48.26 Nm), and in tension by model B (48.72 Nm). The highest stiffness was demonstrated by model 1 (up to 42.38 kNm/rad), while among the alternative models, model C showed the best result in tension (33.98 kNm/rad). Due to the favourable increase in bending moment under compression in model A and the insignificant changes under tension across all variants, model A is considered the optimal solution. To enhance the strength of the door frame, offset holes can be applied as proposed in this model.
- Open Access
- 13 March 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (3) , 134
Comparative Analysis of Bending and Rolling Shear Performance of Poplar and Hybrid Maple–Poplar Cross-Laminated Timber (CLT)
Cross-laminated timber (CLT) is gaining popularity as a sustainable alternative to traditional building materials. However, the decline of natural vegetation and the growth of plantation hardwoods has led the researchers to consider alternatives. This study presents a comparative analysis of bending and rolling shear performance of homogenous poplar (Populus nigra L.) CLT and hybrid CLT, with maple (Acer platanoides L.), in the outer layer and poplar in the core, compared to spruce (Picea abies (L.), H. Karst.) CLT. The CLT panels were prepared using one-component polyurethane (1C-PUR) and melamine adhesive (ME). Poplar CLT exhibited equal or better properties than spruce CLT. The outer maple layer in the hybrid CLT enhanced the global bending modulus (Emg) and bending strength (fm) by 74% and 37%, respectively, due to its higher modulus of elasticity better shear resistance by reducing the cross-layer stress concentrations and rolling shear failure. Additionally, both the adhesive types and wood species significantly influenced the fm, Emg, and rolling shear strength (fr) independently, while their interaction effect was found to be non-significant. The experimental bending stiffness was higher than the theoretical values. The shear analogy method provided the most accurate results for bending and shear strengths, while bending stiffness was best predicted by the modified gamma method, with minor variations. The finite-element models (FEMs) also produced results with a deviation of only 10%.
- 13 March 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (3) , 134
Open AccessComparative Analysis of Bending and Rolling Shear Performance of Poplar and Hybrid Maple–Poplar Cross-Laminated Timber (CLT)
Cross-laminated timber (CLT) is gaining popularity as a sustainable alternative to traditional building materials. However, the decline of natural vegetation and the growth of plantation hardwoods has led the researchers to consider alternatives. This study presents a comparative analysis of bending and rolling shear performance of homogenous poplar (Populus nigra L.) CLT and hybrid CLT, with maple (Acer platanoides L.), in the outer layer and poplar in the core, compared to spruce (Picea abies (L.), H. Karst.) CLT. The CLT panels were prepared using one-component polyurethane (1C-PUR) and melamine adhesive (ME). Poplar CLT exhibited equal or better properties than spruce CLT. The outer maple layer in the hybrid CLT enhanced the global bending modulus (Emg) and bending strength (fm) by 74% and 37%, respectively, due to its higher modulus of elasticity better shear resistance by reducing the cross-layer stress concentrations and rolling shear failure. Additionally, both the adhesive types and wood species significantly influenced the fm, Emg, and rolling shear strength (fr) independently, while their interaction effect was found to be non-significant. The experimental bending stiffness was higher than the theoretical values. The shear analogy method provided the most accurate results for bending and shear strengths, while bending stiffness was best predicted by the modified gamma method, with minor variations. The finite-element models (FEMs) also produced results with a deviation of only 10%.
- Open Access
Evaluating Mechanical Properties and Suitability of Aspen (Populus tremula L.) Load Bearing Replacements in Historical Constructions
The replacement of historical load-bearing wooden elements made from not commonly used species such as Populus tremula L. presents significant challenges. As these species are seldomly used in modern construction, a knowledge gap exists regarding their implementation in accordance with current building codes. This study investigates the mechanical properties of European aspen (Populus tremula L.) from central Slovakia as a potential replacement for historical structures. Notably, poplar species, including European aspen, have historically been utilized for construction across various landscapes in Europe. We conducted experimental testing on visually graded aspen timber to determine the dynamic modulus of elasticity (MOEdyn,ultr), modulus of elasticity (MOE), modulus of rupture (MOR), and density. The results were analyzed and compared to established standards for structural timber. Notably, the 5th percentileof the strength distribution (f0.05) was determined to be 28.78 MPa, while the characteristic strength (fk) was 26.23 MPa, and the modulus of elasticity (Eg12) was 13.60 MPa. The correlation between MOR and dynamic MOE facilitated the determination of MOR by non-destructive testing (NDT) using the Sylvatest Duo®. This simple linear model could grade 49% of boards into the higher strength class C30. The additional parameters and their interactions in multiregresssion models improved the predictability of the bending strength of aspen. The advanced model graded 68% of boards into C30. These characteristics, along with aspen’s growth potential, make it a promising candidate for replacing damaged structural elements in historical constructions. Our findings contribute to the understanding of the potential of European aspen as a structural timber, highlighting its viability as a fast-growing hardwood species.
Open AccessEvaluating Mechanical Properties and Suitability of Aspen (Populus tremula L.) Load Bearing Replacements in Historical Constructions
The replacement of historical load-bearing wooden elements made from not commonly used species such as Populus tremula L. presents significant challenges. As these species are seldomly used in modern construction, a knowledge gap exists regarding their implementation in accordance with current building codes. This study investigates the mechanical properties of European aspen (Populus tremula L.) from central Slovakia as a potential replacement for historical structures. Notably, poplar species, including European aspen, have historically been utilized for construction across various landscapes in Europe. We conducted experimental testing on visually graded aspen timber to determine the dynamic modulus of elasticity (MOEdyn,ultr), modulus of elasticity (MOE), modulus of rupture (MOR), and density. The results were analyzed and compared to established standards for structural timber. Notably, the 5th percentileof the strength distribution (f0.05) was determined to be 28.78 MPa, while the characteristic strength (fk) was 26.23 MPa, and the modulus of elasticity (Eg12) was 13.60 MPa. The correlation between MOR and dynamic MOE facilitated the determination of MOR by non-destructive testing (NDT) using the Sylvatest Duo®. This simple linear model could grade 49% of boards into the higher strength class C30. The additional parameters and their interactions in multiregresssion models improved the predictability of the bending strength of aspen. The advanced model graded 68% of boards into C30. These characteristics, along with aspen’s growth potential, make it a promising candidate for replacing damaged structural elements in historical constructions. Our findings contribute to the understanding of the potential of European aspen as a structural timber, highlighting its viability as a fast-growing hardwood species.
- Open Access
Valorization of Wood-Based Waste from Grapevine
This article deals with the possibility of valorizing wood waste from grapevine cultivation of the varieties Pesecká leánka (white graft) and Frankovka modrá (red graft), grown in Slovakia. From the point of view of chemical composition, two methods (water and ethyl alcohol) were performed for the determination of extractives, acid-insoluble (Klason) lignin, and structural carbohydrates, and FTIR spectra of the grape samples were recorded. Mechanical strength, compression test parallel to the grain, and morphological properties (fiber length, width, and shape factor using a fiber tester) were carried out. The energy potential of grapevines was evaluated by determining the calorific value. According to the results, the relatively high content of carbohydrates (54.19%–55.27%) provides a prerequisite for acid or enzymatic hydrolysis to produce monosaccharides or second-generation bioethanol. FTIR spectra confirmed the higher content of lignin and cellulose in red grapes. The compression strength of grape cuttings (37.34 MPa—red; 32.34 MPa—white) was comparable to the strength of softwood species; hence, these wastes can be used for particleboard or fiberboard production. Average fiber length is comparable to non-wood species; thus, grape cutting can be used for pulp and paper production. The calorific value of grape cuttings ranged from 18.68 MJ·kg−1 (white) to 18.91 MJ·kg−1 (red), with pellets having 16.96 MJ·kg−1. The energetic potential of grape cuttings was comparable to that of other wooden materials; on the other hand, the ash content of pellets from grape cuttings (10.54%) greatly exceeded the limit given by the EN ISO 17225-1 standard, which is a significant disadvantage to pellets used for heating.
Open AccessValorization of Wood-Based Waste from Grapevine
This article deals with the possibility of valorizing wood waste from grapevine cultivation of the varieties Pesecká leánka (white graft) and Frankovka modrá (red graft), grown in Slovakia. From the point of view of chemical composition, two methods (water and ethyl alcohol) were performed for the determination of extractives, acid-insoluble (Klason) lignin, and structural carbohydrates, and FTIR spectra of the grape samples were recorded. Mechanical strength, compression test parallel to the grain, and morphological properties (fiber length, width, and shape factor using a fiber tester) were carried out. The energy potential of grapevines was evaluated by determining the calorific value. According to the results, the relatively high content of carbohydrates (54.19%–55.27%) provides a prerequisite for acid or enzymatic hydrolysis to produce monosaccharides or second-generation bioethanol. FTIR spectra confirmed the higher content of lignin and cellulose in red grapes. The compression strength of grape cuttings (37.34 MPa—red; 32.34 MPa—white) was comparable to the strength of softwood species; hence, these wastes can be used for particleboard or fiberboard production. Average fiber length is comparable to non-wood species; thus, grape cutting can be used for pulp and paper production. The calorific value of grape cuttings ranged from 18.68 MJ·kg−1 (white) to 18.91 MJ·kg−1 (red), with pellets having 16.96 MJ·kg−1. The energetic potential of grape cuttings was comparable to that of other wooden materials; on the other hand, the ash content of pellets from grape cuttings (10.54%) greatly exceeded the limit given by the EN ISO 17225-1 standard, which is a significant disadvantage to pellets used for heating.
- Open Access
- 22 February 2022
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 10 (9) , 3016-3026
Nanoscale FTIR and Mechanical Mapping of Plant Cell Walls for Understanding Biomass Deconstruction
- 22 February 2022
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 10 (9) , 3016-3026
Open AccessNanoscale FTIR and Mechanical Mapping of Plant Cell Walls for Understanding Biomass Deconstruction
- 24 August 2020
- Published by Springer Nature in Annals of Forest Science
- Vol. 77 (3) , 1-15
Variation in leaf anatomy, vascular traits and nanomechanical cell-wall properties among European beech (Fagus sylvatica L.) provenances
- 24 August 2020
- Published by Springer Nature in Annals of Forest Science
- Vol. 77 (3) , 1-15
Variation in leaf anatomy, vascular traits and nanomechanical cell-wall properties among European beech (Fagus sylvatica L.) provenances
- 29 June 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (1) , 56-64
Surface properties of thermally treated European beech wood studied by PeakForce Tapping atomic force microscopy and Fourier-transform infrared spectroscopy
Natural constituents of wood cell-wall layers are affected in various ways by thermal treatment. This study investigated the effect of high-temperature treatment on the properties of cell-wall layers. The properties were studied using PeakForce quantitative nanomechanical mapping and Fourier-transform infrared spectroscopy (FTIR). European beech wood was thermally treated at 200 °C for 1, 3, and 5 h in an oxidizing atmosphere. Modulus of elasticity, adhesion force, and roughness of the secondary S2 layer and the compound middle lamella (CML) were determined using atomic force microscopy (AFM). Results showed that both the S2 layer and CML were affected by thermal treatment. Stiffening of the S2 layer was caused by increased crystallinity of the cellulose-dominated component, having peaked after 1 h of treatment. The degradation thereafter resulted in a decrease of the S2 as well as the CML stiffness. An increase of CML roughness after 3 h of treatment was associated with the effect of thermal degradation on CML integrity. The analysis suggested that the reduction in syringyl lignin is potentially associated with an increase in adhesion of cell-wall layers.
- 29 June 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (1) , 56-64
Surface properties of thermally treated European beech wood studied by PeakForce Tapping atomic force microscopy and Fourier-transform infrared spectroscopy
Natural constituents of wood cell-wall layers are affected in various ways by thermal treatment. This study investigated the effect of high-temperature treatment on the properties of cell-wall layers. The properties were studied using PeakForce quantitative nanomechanical mapping and Fourier-transform infrared spectroscopy (FTIR). European beech wood was thermally treated at 200 °C for 1, 3, and 5 h in an oxidizing atmosphere. Modulus of elasticity, adhesion force, and roughness of the secondary S2 layer and the compound middle lamella (CML) were determined using atomic force microscopy (AFM). Results showed that both the S2 layer and CML were affected by thermal treatment. Stiffening of the S2 layer was caused by increased crystallinity of the cellulose-dominated component, having peaked after 1 h of treatment. The degradation thereafter resulted in a decrease of the S2 as well as the CML stiffness. An increase of CML roughness after 3 h of treatment was associated with the effect of thermal degradation on CML integrity. The analysis suggested that the reduction in syringyl lignin is potentially associated with an increase in adhesion of cell-wall layers.
- Open Access
- 20 April 2019
- Published by Springer Nature in Journal of Wood Science
- Vol. 65 (1) , 21
Changes in chemical and optical properties of silver fir (Abies alba L.) wood due to thermal treatment
- 20 April 2019
- Published by Springer Nature in Journal of Wood Science
- Vol. 65 (1) , 21
Open AccessChanges in chemical and optical properties of silver fir (Abies alba L.) wood due to thermal treatment