Francisco Javier Molina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Francisco Javier Molina has a total of 146 co-authors. Here are the top co-authors by number of shared publications:
Pierre Pegon
Directorate for Space, Security and Migration, Safety and Security of Buildings Unit European Commission, Joint Research Centre Ispra VA Italy
7 shared publications- Simone Peloso
European Commission Joint Research Centre Ispra, Ispra, Lombardy, Italy
7 shared publications - Marco Lamperti Tornaghi
European Commission Joint Research Centre Ispra, Ispra, Lombardy, Italy
6 shared publications G. Magonette
European Commission, Joint Research Centre, IPSC, ELSA Laboratory, 21020 Ispra (Varese), Italy
4 shared publications- Oreste Salvatore Bursi
University of Trento
4 shared publications - Pierre Pegon
European Commission Joint Research Centre (JRC) Ispra Italy
4 shared publications
Latest Publications
- Open Access
- 5 October 2026
- Published by CERN in Open Research Europe
ERIES-RecycleSlab - Structural behaviour of recycled aggregate reinforced concrete flat slabs with drop panels under seismic and cyclic actions: A dataset
This paper presents the dataset collected within the ERIES-RecycleSlab research project, which investigated the seismic performance of a full-scale, two-storey flat-slab building with drop panels constructed using concrete incorporating coarse recycled concrete aggregates (CRCAC). The structure was subjected to combined gravity and lateral actions through a sequence of pseudo-dynamic seismic tests considering two intensity levels, corresponding to the Serviceability Limit State (SLS) and the Ultimate Limit State (ULS). Subsequently, cyclic horizontal loading was applied under constant gravity loads, with progressively increasing displacement amplitudes until near-failure conditions were reached. A brief description of the experimental setup describing the structural design, testing protocol, specimen geometry and material characterization is presented. The testing of the full-scale two-storey flat slab structure was carried out at the European Laboratory for Structural Assessment (ELSA) of the European Commission’s Joint Research Centre.
- 5 October 2026
- Published by CERN in Open Research Europe
Open AccessERIES-RecycleSlab - Structural behaviour of recycled aggregate reinforced concrete flat slabs with drop panels under seismic and cyclic actions: A dataset
This paper presents the dataset collected within the ERIES-RecycleSlab research project, which investigated the seismic performance of a full-scale, two-storey flat-slab building with drop panels constructed using concrete incorporating coarse recycled concrete aggregates (CRCAC). The structure was subjected to combined gravity and lateral actions through a sequence of pseudo-dynamic seismic tests considering two intensity levels, corresponding to the Serviceability Limit State (SLS) and the Ultimate Limit State (ULS). Subsequently, cyclic horizontal loading was applied under constant gravity loads, with progressively increasing displacement amplitudes until near-failure conditions were reached. A brief description of the experimental setup describing the structural design, testing protocol, specimen geometry and material characterization is presented. The testing of the full-scale two-storey flat slab structure was carried out at the European Laboratory for Structural Assessment (ELSA) of the European Commission’s Joint Research Centre.
- Open Access
- 22 September 2026
- Published by CERN in Open Research Europe
Extruded Tunnel Lining Regeneration Project (ETLR): experimental campaign on real scale SFRC tunnel mock-ups
Background Automation in the construction industry is gaining increasing relevance, driven by the need to enhance productivity, foster innovation, and meet evolving societal demands. Slip-forming with extrudable steel fibre-reinforced concrete (SFRC) offers an innovative framework for the maintenance and refurbishment of highway and railway tunnels. However, its structural performance requires full-scale validation before adoption in practice. Methods Four full-scale mock-ups replicating a motorway tunnel lining were constructed using slip-forming with extrudable SFRC and tested under load conditions simulating the relevant action combinations for tunnel linings in the intended scenarios. Both symmetric and non-symmetric loading combinations were examined, including a sequential loading case to assess accumulated damage and residual bearing capacity. Digital Image Correlation (DIC) analysis was performed to study cracking in the mock-ups, enabling computation of crack opening, which was related to the load applied by the hydraulic jacks employed in the experiment. Testing was conducted at the ELSA laboratory of the European Commission, Joint Research Centre in Ispra, as part of the OPENLAB ETLR project. Results The relationship between crack opening and applied load enabled characterisation of the post-cracking residual capacity of the SFRC tunnel lining structure under the tested loading combinations, including its behaviour under sequential loading and the associated accumulation of damage. Conclusions The full-scale tests provide a preliminary validation of the adopted design criteria and an assessment of the effectiveness and structural reliability of the proposed slip-forming SFRC technology for tunnel lining refurbishment.
- 22 September 2026
- Published by CERN in Open Research Europe
Open AccessExtruded Tunnel Lining Regeneration Project (ETLR): experimental campaign on real scale SFRC tunnel mock-ups
Background Automation in the construction industry is gaining increasing relevance, driven by the need to enhance productivity, foster innovation, and meet evolving societal demands. Slip-forming with extrudable steel fibre-reinforced concrete (SFRC) offers an innovative framework for the maintenance and refurbishment of highway and railway tunnels. However, its structural performance requires full-scale validation before adoption in practice. Methods Four full-scale mock-ups replicating a motorway tunnel lining were constructed using slip-forming with extrudable SFRC and tested under load conditions simulating the relevant action combinations for tunnel linings in the intended scenarios. Both symmetric and non-symmetric loading combinations were examined, including a sequential loading case to assess accumulated damage and residual bearing capacity. Digital Image Correlation (DIC) analysis was performed to study cracking in the mock-ups, enabling computation of crack opening, which was related to the load applied by the hydraulic jacks employed in the experiment. Testing was conducted at the ELSA laboratory of the European Commission, Joint Research Centre in Ispra, as part of the OPENLAB ETLR project. Results The relationship between crack opening and applied load enabled characterisation of the post-cracking residual capacity of the SFRC tunnel lining structure under the tested loading combinations, including its behaviour under sequential loading and the associated accumulation of damage. Conclusions The full-scale tests provide a preliminary validation of the adopted design criteria and an assessment of the effectiveness and structural reliability of the proposed slip-forming SFRC technology for tunnel lining refurbishment.
- Open Access
- 8 September 2026
- Published by CERN in Open Research Europe
ERIES-REVAULTS Pseudo-Dynamic tests on a full-scale masonry cross vault system: dataset
This paper presents the dataset generated within the ERIES-REVAULTs experimental campaign, aimed at investigating the in-plane shear behaviour of masonry cross vaults, representative of historic churches. In post-earthquake surveys, the damage associated with this type of mechanism is frequently observed as it is caused by the differential longitudinal displacements of vaults’ supports. To investigate this behaviour, a full-scale masonry specimen was constructed at the European Laboratory for Structural Assessment (ELSA), Joint Research Centre (JRC), Ispra, Italy, and tested using Pseudo-Dynamic (PsD) testing technique, to reproduce the seismic action. The experimental campaign included an initial testing phase on the as-built specimen during which a seismic action was applied. Then, repair, strengthening with a Steel-Reinforced Grout (SRG) system and a second testing phase under the same seismic input conditions followed. The paper includes information on the specimen’s geometry, its construction details, materials, strengthening intervention, test setup, actuators configuration, instrumentation and loading protocols. Most of this information is also included in the shared dataset.
- 8 September 2026
- Published by CERN in Open Research Europe
Open AccessERIES-REVAULTS Pseudo-Dynamic tests on a full-scale masonry cross vault system: dataset
This paper presents the dataset generated within the ERIES-REVAULTs experimental campaign, aimed at investigating the in-plane shear behaviour of masonry cross vaults, representative of historic churches. In post-earthquake surveys, the damage associated with this type of mechanism is frequently observed as it is caused by the differential longitudinal displacements of vaults’ supports. To investigate this behaviour, a full-scale masonry specimen was constructed at the European Laboratory for Structural Assessment (ELSA), Joint Research Centre (JRC), Ispra, Italy, and tested using Pseudo-Dynamic (PsD) testing technique, to reproduce the seismic action. The experimental campaign included an initial testing phase on the as-built specimen during which a seismic action was applied. Then, repair, strengthening with a Steel-Reinforced Grout (SRG) system and a second testing phase under the same seismic input conditions followed. The paper includes information on the specimen’s geometry, its construction details, materials, strengthening intervention, test setup, actuators configuration, instrumentation and loading protocols. Most of this information is also included in the shared dataset.
- Open Access
- 13 June 2026
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 45 (3)
Evaluation of Stereovision Tracking of Targets with Gaussian Pixel Intensity Distribution for Measuring 3D Displacements of Structures
- 13 June 2026
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 45 (3)
Open AccessEvaluation of Stereovision Tracking of Targets with Gaussian Pixel Intensity Distribution for Measuring 3D Displacements of Structures
- Open Access
- 14 January 2026
- Published by CERN in Open Research Europe
- Vol. 5, 308
Dissipate and Recentre (D&R) experimental campaign on real scale GFRP composite frame structures: data set
In the scope of the Dissipate&Recentre project, which was granted access to the ELSA Reaction Wall of the Joint Research Centre physical research infrastructure of the European Commission, large scale composite frame structures were tested under lateral loading. The test specimens, comprising pultruded glass fibre reinforced polymer (GFRP) profiles, connected with stainless steel elements, had two longitudinal (test direction) bays, two storeys and a shorter transverse bay. Concrete slabs were provided as flooring system, simulating a quasi-permanent load level – as that used in seismic design. A total of 4 full-scale specimens were tested, two including a bracing system, also comprising pultruded GFRP profiles, and two without bracings. For each configuration, one specimen was tested under monotonic loading and the other under cyclic loading. The aim of this paper is to disseminate the experimental data obtained in these tests. To that end, the experimental campaign is thoroughly described, including all the relevant details of the test specimens, the construction process, the setup and instrumentation, and the test programme. Additionally, a brief description of the test observations is also provided. The test results showed that the structural integrity of these GFRP frames was maintained up to 2% inter-storey drifts, for both braced and unbraced configurations, presenting very limited damage. These results indicate that GFRP frame structures may be designed to withstand significant seismic actions.
- 14 January 2026
- Published by CERN in Open Research Europe
- Vol. 5, 308
Open AccessDissipate and Recentre (D&R) experimental campaign on real scale GFRP composite frame structures: data set
In the scope of the Dissipate&Recentre project, which was granted access to the ELSA Reaction Wall of the Joint Research Centre physical research infrastructure of the European Commission, large scale composite frame structures were tested under lateral loading. The test specimens, comprising pultruded glass fibre reinforced polymer (GFRP) profiles, connected with stainless steel elements, had two longitudinal (test direction) bays, two storeys and a shorter transverse bay. Concrete slabs were provided as flooring system, simulating a quasi-permanent load level – as that used in seismic design. A total of 4 full-scale specimens were tested, two including a bracing system, also comprising pultruded GFRP profiles, and two without bracings. For each configuration, one specimen was tested under monotonic loading and the other under cyclic loading. The aim of this paper is to disseminate the experimental data obtained in these tests. To that end, the experimental campaign is thoroughly described, including all the relevant details of the test specimens, the construction process, the setup and instrumentation, and the test programme. Additionally, a brief description of the test observations is also provided. The test results showed that the structural integrity of these GFRP frames was maintained up to 2% inter-storey drifts, for both braced and unbraced configurations, presenting very limited damage. These results indicate that GFRP frame structures may be designed to withstand significant seismic actions.
- Open Access
- 13 January 2026
- Published by Elsevier in Engineering Structures
- Vol. 352
Modular building system with rocking cross-laminated timber panels for reusable construction: Experimental seismic assessment
- 13 January 2026
- Published by Elsevier in Engineering Structures
- Vol. 352
Open AccessModular building system with rocking cross-laminated timber panels for reusable construction: Experimental seismic assessment
- Open Access
- 8 October 2025
- Published by CERN in Open Research Europe
- Vol. 5, 308
Dissipate and Recentre (D&R) experimental campaign on real scale GFRP composite frame structures: data set
In the scope of the Dissipate&Recentre project, which was granted access to the ELSA Reaction Wall of the Joint Research Centre physical research infrastructure of the European Commission, large scale composite frame structures were tested under lateral loading. The test specimens, comprising pultruded glass fibre reinforced polymer (GFRP) profiles, connected with stainless steel elements, had two longitudinal (test direction) bays, two storeys and a shorter transverse bay. Concrete slabs were provided as flooring system, simulating a quasi-permanent load level – as that used in seismic design. A total of 4 full-scale specimens were tested, two including a bracing system, also comprising pultruded GFRP profiles, and two without bracings. For each configuration, one specimen was tested under monotonic loading and the other under cyclic loading. The aim of this paper is to disseminate the experimental data obtained in these tests. To that end, the experimental campaign is thoroughly described, including all the relevant details of the test specimens, the construction process, the setup and instrumentation, and the test programme. Additionally, a brief description of the test observations is also provided. The test results showed that the structural integrity of these GFRP frames was maintained up to 2% inter-storey drifts, for both braced and unbraced configurations, presenting very limited damage. These results indicate that GFRP frame structures may be designed to withstand significant seismic actions.
- 8 October 2025
- Published by CERN in Open Research Europe
- Vol. 5, 308
Open AccessDissipate and Recentre (D&R) experimental campaign on real scale GFRP composite frame structures: data set
In the scope of the Dissipate&Recentre project, which was granted access to the ELSA Reaction Wall of the Joint Research Centre physical research infrastructure of the European Commission, large scale composite frame structures were tested under lateral loading. The test specimens, comprising pultruded glass fibre reinforced polymer (GFRP) profiles, connected with stainless steel elements, had two longitudinal (test direction) bays, two storeys and a shorter transverse bay. Concrete slabs were provided as flooring system, simulating a quasi-permanent load level – as that used in seismic design. A total of 4 full-scale specimens were tested, two including a bracing system, also comprising pultruded GFRP profiles, and two without bracings. For each configuration, one specimen was tested under monotonic loading and the other under cyclic loading. The aim of this paper is to disseminate the experimental data obtained in these tests. To that end, the experimental campaign is thoroughly described, including all the relevant details of the test specimens, the construction process, the setup and instrumentation, and the test programme. Additionally, a brief description of the test observations is also provided. The test results showed that the structural integrity of these GFRP frames was maintained up to 2% inter-storey drifts, for both braced and unbraced configurations, presenting very limited damage. These results indicate that GFRP frame structures may be designed to withstand significant seismic actions.
- 7 February 2025
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 29 (5) , 1145-1164
Improvement of the Pseudo-Dynamic Testing Method for Buildings that are Seismically Protected by Means of Dissipative Devices
- 7 February 2025
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 29 (5) , 1145-1164
Improvement of the Pseudo-Dynamic Testing Method for Buildings that are Seismically Protected by Means of Dissipative Devices
- Open Access
- 2 December 2023
- Published by Elsevier in Engineering Structures
- Vol. 300
Seismic experimental analysis of a full-scale steel building with passive fire protections
- 2 December 2023
- Published by Elsevier in Engineering Structures
- Vol. 300
Open AccessSeismic experimental analysis of a full-scale steel building with passive fire protections
- Open Access
- 3 May 2023
- Published by Universidad de Alicante Servicio de Publicaciones in Lucentum
- No. 42,p. 33-50
Metodología de detección con dron (RPAS) aplicada a la prospección de arte rupestre prehistórico
La prospección, detección y documentación de arte rupestre prehistórico en paredes, abrigos y cuevas poco profundas está, a menudo, condicionada por su accesibilidad. Las características geográficas del entorno y las transformaciones del paisaje a lo largo de milenios, tanto por causas naturales como antrópicas, son factores determinantes a tener en cuenta. El objetivo de este trabajo es contribuir a crear un marco metodológico que permita incorporar el uso de drones a la prospección arqueológica para la localización de yacimientos con arte rupestre situados en zonas de difícil acceso, partiendo de la experiencia desarrollada en el proyecto Arte rupestre y paisajes culturales en la montaña de Alicante. La observación de pinturas y grabados de forma segura sería, por tanto, la primera fase en los trabajos de prospección en estos entornos de geografía compleja, permitiendo la selección de aquellos abrigos con resultado positivo para su acceso mediante diferentes métodos tradicionales, con el objeto de realizar los pertinentes trabajos de verificación, documentación y estudio, previamente autorizados por la administración competente. Esta metodología puede aplicarse no solo en la investigación de Arte rupestre prehistórico, sino también en el contexto de los estudios de impacto patrimonial en relación con la conservación preventiva, teniendo en cuenta las diversas problemáticas que amenazan este patrimonio, tales como promociones urbanísticas, explotaciones de cantería o la práctica de actividades lúdicas y deportivas al aire libre. De igual modo, si bien este estudio se centra en las manifestaciones prehistóricas, podría ser empleado en la detección de enclaves sobre soportes similares de cualquier período histórico.
- 3 May 2023
- Published by Universidad de Alicante Servicio de Publicaciones in Lucentum
- No. 42,p. 33-50
Open AccessMetodología de detección con dron (RPAS) aplicada a la prospección de arte rupestre prehistórico
La prospección, detección y documentación de arte rupestre prehistórico en paredes, abrigos y cuevas poco profundas está, a menudo, condicionada por su accesibilidad. Las características geográficas del entorno y las transformaciones del paisaje a lo largo de milenios, tanto por causas naturales como antrópicas, son factores determinantes a tener en cuenta. El objetivo de este trabajo es contribuir a crear un marco metodológico que permita incorporar el uso de drones a la prospección arqueológica para la localización de yacimientos con arte rupestre situados en zonas de difícil acceso, partiendo de la experiencia desarrollada en el proyecto Arte rupestre y paisajes culturales en la montaña de Alicante. La observación de pinturas y grabados de forma segura sería, por tanto, la primera fase en los trabajos de prospección en estos entornos de geografía compleja, permitiendo la selección de aquellos abrigos con resultado positivo para su acceso mediante diferentes métodos tradicionales, con el objeto de realizar los pertinentes trabajos de verificación, documentación y estudio, previamente autorizados por la administración competente. Esta metodología puede aplicarse no solo en la investigación de Arte rupestre prehistórico, sino también en el contexto de los estudios de impacto patrimonial en relación con la conservación preventiva, teniendo en cuenta las diversas problemáticas que amenazan este patrimonio, tales como promociones urbanísticas, explotaciones de cantería o la práctica de actividades lúdicas y deportivas al aire libre. De igual modo, si bien este estudio se centra en las manifestaciones prehistóricas, podría ser empleado en la detección de enclaves sobre soportes similares de cualquier período histórico.