Michael Joseph Ford

Polymerization-induced phase separation (PIPS) allows for the control of thermoset morphologies and properties, enabling the tuning of domain sizes and thermomechanical response. However, its use in generating substructural features in additively manufactured materials has been limited. In this work, we combine epoxy PIPS with UV curable acrylate and rheological modifiers to print nano- to macro-phase separating materials via a two-step, dual-cure approach. This method enables direct ink write printing of hierarchical structures with both controlled morphologies through phase separation and macroscale architecture through print design. We find that formulations for phase-separating materials require judicious incorporation of additives to enable printability and to provide sufficient green strength. Atomic force microscopy-nano infrared mapping reveals tunable, reticulated nano- to micron-scale domains of the resultant multiphase materials and their morphology changes due to additives, resulting in alterations to thermomechanical and tensile properties. Shape memory behavior is also demonstrated through multimaterial additive manufacturing of epoxies with functionally graded internal morphology using active mixing techniques, highlighting this method’s ability to fabricate complex architectures with controlled morphologies and thermomechanical response.

We first briefly describe the history and motivation behind Cherenkov and scintillation light detection. We then discuss the instrumentation needed to detect these photons as it applies to both photodetectors and readout electronics. One of the motivations is future large neutrino detectors that could, in principle, differentiate between Cherenkov and scintillation light if using novel water-based scintillators. In this paper, we present the first measurements utilizing the second generation of Large Area Picosecond Photodetectors (LAPPDs) in conjunction with commercial system-on-a-chip readouts from Nalu Scientific—in particular, the High Density System on Chip (HDSoC) and Advanced ASoC Rapid Digitizer, Variable Adaptive Readout Chip (AARDVARC) platforms. These state-of-the-art full-waveform digitizers feature sampling rates on the order of 1 and 10 samples per nanosecond, respectively. Using a picosecond laser, we measured the timing jitter between a pair of LAPPD channels, demonstrating the potential of this setup for precise timing applications.

Extrusion 3D printing has advanced the manufacturing of complex liquid crystal elastomer (LCE) architectures. In parallel, donor-acceptor Stenhouse adducts (DASAs), a class of white-light-responsive photoswitches, have enabled both photochemical and photothermal LCE actuation. However, DASA-LCEs have yet to be extruded and 3D-printed. Two key challenges exist: DASA's inherent sensitivity to heat and radicals can lead to degradation during ink preparation and printing, and small changes in the concentration of the added DASA component impact the properties of the extrudable ink, requiring reoptimization of well-established 3D-printing protocols. To overcome these challenges, we present a post-printing functionalization strategy that circumvents these limitations. Residual secondary amines, inherent to inks synthesized via standard aza-Michael addition, serve as active sites for covalent attachment of DASA photoresponsive groups following printing and cross-linking. Our method means that DASAs can be directly grafted onto 3D-printed aza-Michael LCEs without modifying the ink formulation or processing. The resulting DASA-LCEs exhibit wavelength tunability within the visible range and a variety of photothermal and photochemical responses. The post-functionalization can occur within 2 min and enables spatial control of the DASA concentration, producing films with tunable color gradients and locally varied photothermal and photochemical responses under visible light. This approach enables the rapid fabrication of DASA-based light-responsive LCEs using established ink formulations with the potential for the design of complex 3D architectures.

Silicone foams were produced by dispersing an incompatible liquid phase (i.e. a non-solvent) into an uncured, liquid silicone. The formulation and processing parameters were varied to see the effect on porosity and pore morphology. Specifically, two fluorosilanes were added to stabilize the inclusion of fluorinated solvents as blowing agents. As the floruosilane content increased, the void content increased up to about 44 vol. % when the fluorosilane comprised 18 wt. % of the initial formulation. Fumed silica that was treated with a fluorinated silane was also used to try to stabilize the dispersed liquid. While the fumed silica content did not have a strong effect on the total void content, the morphology changed when silica content changed. Various fluorinated solvents with distinct chemical structures were used as the non-solvent and then removed after curing of the silicone. The interaction of the internal non-solvent phase and the silicone phase was expected to influence the porosity. These insights highlight how the manipulation of formulation and processing parameters, focusing on the inclusion of fluorosilanes and fluorinated solvents, contributes to the understanding of how incompatible liquid phases interact with silicone matrices to control porosity and pore morphology. Additionally, these interactions also influenced processability, leading to formulations that could be printed. Higher content of non-solvent inclusions could increase the yield stress and storage modulus of an uncured formulation, leading to the ability to tune intrastrand porosity while a 3D printed architecture could be modified to introduce porosity between the strands. In addition to fluorinated solvents, we also considered non-fluorinated solvents since these may be more industrially relevant in the future. Overall, this approach provides an alternative route to producing porous foams that can be 3D printed, which could be useful for applications like cushioning and protective gear.

In this report, we describe the incorporation of single-walled carbon nanotubes (CNTs) into 3D printable siloxane elastomers for electrostatic dissipation. The composite was characterized, focusing on how rheological and mechanical properties of the siloxane are affected at various CNT loading levels. Electrical properties were also characterized to develop materials with effective electrostatic dissipation. We demonstrate that low loadings (<1 wt %) of CNTs can be sufficiently dispersed into silicone resins that can be 3D printed, and the resulting material shows a significant improvement in electrostatic dissipation through the reduction in electrical resistivity with minimal effect on its mechanical properties.

Soft materials that exhibit compliance, programmability, and reconfigurability can have a transformative impact as electronic skin for applications in wearable electronics/soft robotics. There has been significant progress in soft conductive materials; however, achieving electrically controlled and reversible changes in conductivity and circuit connectivity remains challenging. To overcome this limitation, a soft material architecture with reconfigurable conductive networks of silver flakes embedded within a hydrogel matrix is presented. The conductive networks can be reversibly created/disconnected through various stimuli, including current, humidity, or temperature. Such stimuli affect electrical connectivity of the hydrogel by controlling its water content, which can be modulated by evaporation under ambient conditions (passive dehydration), evaporation through electrical Joule heating (active dehydration), or absorption of additional water (rehydration). The resulting change in electrical conductivity is reversible and repeatable, endowing the composite with on‐demand reconfigurable conductivity. To highlight this material's unique properties, it is shown that conductive traces can be reconfigured after severe damage and revert to lower conductivity after rehydration. Additionally, a quadruped robot is demonstrated that can respond to stimuli by changing direction following exposure to excess water, thereby achieving reprogrammable locomotion behaviors.