XPXiaolong Peng

Xiaolong Peng

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Xiaolong Peng has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • DSP-based controller-in-the-loop speed control system for marine diesel generator sets

    by Xiaolong Peng, Weifeng Shi

    Aiming at the problem of prime mover speed variation caused by frequent load variation of Marine diesel generator set under actual operating conditions, a speed control system of Marine diesel generator sets based on DSP is designed, the speed control principle of Marine diesel generator sets is analyzed, and the hardware block diagram and software flow of the system are designed. In terms of hardware, the TMS320F28335 chip is used as the core components. Regarding the software aspect, a model for the marine diesel generator set has been simply constructed. Serial port to Ethernet interface is used to complete the communication between DSP hardware environment and Simulink environment, and the hardware in loop semi-physical simulation of the system is realized. By adjusting PID parameters, the system simulation waveform changes were analyzed. Finally, the DSP controller performance is verified by increasing and reducing the load abruptly. The results obtained from the simulation indicate that the speed control system possesses high response speed, good stability and strong tracking ability

  • A Semi-analytical Model for Pressure-Dependent Permeability of Tight Sandstone Reservoirs

    by Su-Yang Zhu, Zhi-Min Du, Chuan-Liang Li, Alireza Salmachi, Xiao-Long Peng, Chao-Wen Wang, Ping Yue, Peng Deng


  • Open Access

    Interface condition for the Darcy velocity at the water-oil flood front in the porous medium

    by Xiaolong Peng, Yong Liu, Baosheng Liang, Zhimin Du

    Flood front is the jump interface where fluids distribute discontinuously, whose interface condition is the theoretical basis of a mathematical model of the multiphase flow in porous medium. The conventional interface condition at the jump interface is expressed as the continuous Darcy velocity and fluid pressure (named CVCM). Our study has inspected this conclusion. First, it is revealed that the principle of mass conservation has no direct relation to the velocity conservation, and the former is not the true foundation of the later, because the former only reflects the kinetic characteristic of the fluid particles at one position(the interface), but not the different two parts of fluid on the different side of the interface which required by the interface conditions. Then the reasonableness of CVCM is queried from the following three aspects:(1)Using Mukat’s two phase seepage equation and the mathematical method of apagoge, we have disproved the continuity of each fluid velocity;(2)Since the analytical solution of the equation of Buckley-Leveret equations is acquirable, its velocity jumps at the flood front presents an appropriate example to disprove the CVCM;(3) The numerical simulation model gives impractical result that flood front would stop moving if CVCM were used to calculate the velocities at the interface between two gridcells. Subsequently, a new one, termed as Jump Velocity Condition Model (JVCM), is deduced from Muskat’s two phase seepage equations and Darcy’s law without taking account of the capillary force and compressibility of rocks and fluids. Finally, several cases are presented. And the comparisons of the velocity, pressure difference and the front position, which are given by JVCM, CVCM and SPU, have shown that the result of JVCM is the closest to the exact solution.


  • An Improved Grid Generation Approach for Discrete Fracture Network Modelling Using Line Fracture Concept for Two-Phase Flow Simulation

    by Keke Wang, Xiaolong Peng, Zhimin Du, Manicher Haghighi, Lu Yu

    In traditional Discrete Fracture Network (DFN) method for fractured porous media simulation, fractures are modelled in different scales and orientations using single computational grid. However, a large number of small grids near both ends of fracture are generated, which substantially reduce the computation efficiency. In this paper, a new line fracture approach is presented to avoid generation of small grids. Combined with Multi-Point Flux Approximation (MPFA) algorithm, the simulation efficiency is highly improved without losing accuracy. We present a modified mesh generation algorithm in which the volume of large fractures is set zero by neglecting the fracture width. The fracture aperture (very short line) is treated as single node during mesh generation using the paving method. Therefore, the number of small grids around the fracture is significantly decreased. In this paper, a quadrilateral unstructured grid system is generated using the proposed paving method. Then, by taking the median dual of quadrilateral mesh as the control volume, all fracture properties such as the aperture and permeability are accounted for as independent parameters in discrete fractures. The governing equations of DFN model are derived and solved using MPFA algorithm for oil-water two-phase flow. A new discrete fracture network model using line fracture approach is developed. To show the efficiency and accuracy of the new model, the proposed method is applied to a case study of two separated and two crossed fractures, in the computation domain with the scale of 50 by 50 meters. Compared with the standard DFN model including the width of fractures, the computation efficiency of the new model is highly improved (by 2.5 times), due to the large reduction of grid numbers (20%). Good agreement in water and oil saturation distributions resulted from the two models validates the newly developed method. Simulation of naturally fractured reservoirs has been a challenge for decades. Discrete fracture network modelling is a promising approach. However, without an efficient grid generation method, DFN model is not feasible and practical due to the large amount of computational time. The novelty of the present work is the improved model using line fracture approach. The new grid generation algorithm is coupled with multi-point flux approximation approach for flow simulation in fracture network system. High efficiency and accuracy of the developed method is readily applied to fractured reservoir simulation. Sponsored by NSFC (Natural Science Fund of China - "the numerical simulation of natural fractured reservoir based on the unstructured hexahedral grid system and concurrent computation") (No. 51474179)


  • DFN Model for Flow Simulation in Hydraulically Fractured Wells With Pre-Existing Natural Fractures Using Unstructured Quadrilateral Grids

    by Keke Wang, Xiaolong Peng, Zhimin Du, Manouchehr Haghighi, Muhammad Sayyafzadeh

    Multiphase flow simulation of hydraulically fractured wells with pre-existing natural fractures is a challenging task. Discrete fracture network (DFN) is an effective method to simulate a system of anisotropic fracture network. In DFN method unlike double porosity approach, fractures can be defined in different scales and in different apertures and directions such that all details of fractures will be included in the simulation. Also all the interactions and fluid flow in and between the fractures and within the matrix are modelled in a unified manner, using the same computational grid. We developed software based on DFN model in which both induced fractures and pre-existing natural fractures can be placed at any location and direction in the geological model. Then, quadrilateral unstructured grids are generated using Paving method. Quadrilateral grids are more efficient and more flexible than triangular grids such that the number of quadrilateral grids is reduced to half. A drawback of algorithm in this mesh generation process is that very small grids are generated in the intersection of fractures and in the ends of the fracture grids due to the size difference between the fracture and the matrix. In order to avoid severe time-step restrictions associated with small cells, an endpoint transformation method is used to replace the quadrilateral grids with the triangular grids at both ends of the fracture. As a result, the number of very small grids at the ends of fractures is notably decreased. In this paper, the results of two-phase flow simulation in a hydraulically fractured well with pre-existing natural fractures are presented. For solving the pressure and saturation equations in each grid, the inter region of quadrilateral mesh is taken as a control volume cell and the governing equations are solved using MPFA (Multi-Point Flux Approximation) technique which is designed to give a correct discretization of the flow equations for general non-orthogonal grids. Finally the results of our software are tested to verify its validity in theory, algorithm, and efficiency in calculation.

  • Relativistic energies for diatomic molecule nucleus motions with the spin symmetry

    by Chun-Sheng Jia, Jian-Wei Dai, Lie-Hui Zhang, Jian-Yi Liu, Xiao-Long Peng


  • Enhancing the Safety of Coal Mining by Injecting CO2 into Coalbeds

    by Fei Mo, Xiao Long Peng, Zhi Min Du

    Coal mining begins after coalbed methane (CBM) production which reduces CH4 concentration in coalbeds. However once CH4 concentration reaches the explosion limit, the threat of explosion accident in the coal mine will be greatly increased. Based on safety production principle, this paper analyses the feasibility of CO2 injection through CBM wells to control CH4 concentration and enhance CBM recovery at the same time during CBM production. Safe concentration of CH4 is determined according to its explosion limit and safety factor. Combined with numerical simulation, a CH4 concentration control method by CO2 injection is proposed: firstly the CO2 injection standard is calculated to ensure CH4 safe concentration, and then the optimum CO2 injection rate (14000m3/d) is determined by comparisons between different injection rates. Finally CO2 emission reduction and recycle methods are proposed to achieve effective environmental protection and high economic efficiency.