Kamala Qalandar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kamala Qalandar has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
A. Ma
University of California at Santa Barbara 1 Department of Mechanical Engineering Santa Barbara, California 93106, USA
1 shared publicationB. S. Strachan
Michigan State University 2 Department of Mechanical Engineering East Lansing, Michigan 48823, USA
1 shared publicationBrian Gibson
Department of Mechanical Engineering, University of California, Santa Barbara, USA
1 shared publication- Brian Gibson
Department of Mechanical Engineering, University of California Santa Barbara, Santa Barbara, CA, USA
1 shared publication Cristian Cassella
Department of Electrical and Computer Engineering, Carnegie Melon University, Pittsburgh, USA
1 shared publicationGianluca Piazza
Department of Electrical and Computer Engineering, Carnegie Melon University, Pittsburgh, USA
1 shared publication
Latest Publications
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 709-712
Analysis of the impact of release area on the quality factor of contour-mode resonators by laser Doppler vibrometry
Energy dissipation through the anchors of an aluminum nitride (AlN) MEMS contour-mode resonator (CMR) plays an important role in setting the device quality factor at frequencies under 500MHz [1]. The acoustic energy leaving the resonator is effected, not only by the anchor, but also the portion of the surrounding device layer that has been released from the substrate during fabrication. Typical device simulations used for design do not take into account the motion of this additional area. Using laser Doppler vibrometery and COMSOL simulations we show a variation in device Q by 28% as a result of the motion of this released region.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 709-712
Analysis of the impact of release area on the quality factor of contour-mode resonators by laser Doppler vibrometry
Energy dissipation through the anchors of an aluminum nitride (AlN) MEMS contour-mode resonator (CMR) plays an important role in setting the device quality factor at frequencies under 500MHz [1]. The acoustic energy leaving the resonator is effected, not only by the anchor, but also the portion of the surrounding device layer that has been released from the substrate during fabrication. Typical device simulations used for design do not take into account the motion of this additional area. Using laser Doppler vibrometery and COMSOL simulations we show a variation in device Q by 28% as a result of the motion of this released region.
- 15 December 2014
- Published by AIP Publishing in Applied Physics Letters
- Vol. 105 (24) , 244103
Frequency division using a micromechanical resonance cascade
A coupled micromechanical resonator array demonstrates a mechanical realization of multi-stage frequency division. The mechanical structure consists of a set of N sequentially perpendicular microbeams that are connected by relatively weak elastic elements such that the system vibration modes are localized to individual microbeams and have natural frequencies with ratios close to 1:2:⋯:2N. Conservative (passive) nonlinear inter-modal coupling provides the required energy transfer between modes and is achieved by finite deformation kinematics. When the highest frequency beam is excited, this arrangement promotes a cascade of subharmonic resonances that achieve frequency division of 2j at microbeam j for j = 1, …, N. Results are shown for a capacitively driven three-stage divider in which an input signal of 824 kHz is passively divided through three modal stages, producing signals at 412 kHz, 206 kHz, and 103 kHz. The system modes are characterized and used to delineate the range of AC input voltages and frequencies over which the cascade occurs. This narrow band frequency divider has simple design rules that are scalable to higher frequencies and can be extended to a larger number of modal stages.
- 15 December 2014
- Published by AIP Publishing in Applied Physics Letters
- Vol. 105 (24) , 244103
Frequency division using a micromechanical resonance cascade
A coupled micromechanical resonator array demonstrates a mechanical realization of multi-stage frequency division. The mechanical structure consists of a set of N sequentially perpendicular microbeams that are connected by relatively weak elastic elements such that the system vibration modes are localized to individual microbeams and have natural frequencies with ratios close to 1:2:⋯:2N. Conservative (passive) nonlinear inter-modal coupling provides the required energy transfer between modes and is achieved by finite deformation kinematics. When the highest frequency beam is excited, this arrangement promotes a cascade of subharmonic resonances that achieve frequency division of 2j at microbeam j for j = 1, …, N. Results are shown for a capacitively driven three-stage divider in which an input signal of 824 kHz is passively divided through three modal stages, producing signals at 412 kHz, 206 kHz, and 103 kHz. The system modes are characterized and used to delineate the range of AC input voltages and frequencies over which the cascade occurs. This narrow band frequency divider has simple design rules that are scalable to higher frequencies and can be extended to a larger number of modal stages.