Jana Moravčíková has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Laser Texturing and Coating on the Tribological Properties of the Tool Steels Properties

    by Jana Moravčíková, Roman Moravčík, Martin Sahul, Martin Necpal

    The article is aimed at identifying the influence of laser texturing and subsequent coating with a hard, wear-resistant coating AlCrSiN (nACRo®) on selected tribological properties of the analyzed tool steels for cold work, produced by conventional and powder metallurgy. The substrate from each steel was heat treated to achieve optimal properties regarding the chemical composition and the method of production of the material. Böhler K100 and K390 Microclean® steels were used. These are highly alloyed tool steels used for various types of tools intended for cold work. The obtained results show that the coefficient of friction is increased by coating, but the wear rate is lower compared to the samples which were only textured.


  • Open Access

    Selected Aspects of Precision Machining on CNC Machine Tools

    by Jozef Peterka, Marcel Kuruc, Vitalii Kolesnyk, Ivan Dehtiarov, Jana Moravcikova, Tomas Vopat, Peter Pokorny, Frantisek Jurina, Vladimir Simna

    The work is new due to the type of process used—ultrasonic precision machining—to determine the possible effect of spindle heating (long-term machining) on the precision of the flat surface. It was carried out on a precise ultrasonic machining machine, and the material of workpiece was ceramic Al2O3. A flat surface was machined. Such an experiment has not been feasible until now. The experiment was divided into two days. On the first day, the machining time was 4 h. It is a long enough time to create a temperature-steady state. On the second day, with a cold tool and cold machine tool, we continued where we left off on the first day. This is how we monitored the accuracy of the dimensions of the workpiece on the plane surface. We have achieved the following: The average interface depth achieved values of 0.007089 mm and 0.003667 mm for cold and heated spindles, respectively. It means that when the spindle is not heated, the depth of the interface is higher by 93% (almost double the depth). The average standard deviation of the interface depth is 0.001683 mm and 0.000997 mm for cold and heated spindles, respectively. It means that when the spindle is not heated, the process is not as stable, and the standard deviation is higher by 69%.


  • Open Access

    Optimization of the Interaction Transport System—Transported Medium to Ensure the Required Water Quality

    by Daniela Cvelihárová, Alena Pauliková, Lucia Kopilčáková, Adriana Eštoková, Marieta Georgieva Stefanova, Mária Dománková, Ingrid Šutiaková, Martin Kusý, Jana Moravčíková, Marián Hazlinger

    This article addresses a pressing issue concerning the attainment of required drinking water quality in municipal settings. The solution lies in optimizing the interaction among multiple elements involved in this process. The interaction encompasses the transport system with its geometric, physicochemical, and operational characteristics, as well as the transported medium, which is drinking water with its physicochemical, operational, and incrustation characteristics. This article provides an overview of the current state of piped water systems and explores the integration of factors influencing the formation of incrustation to minimize its occurrence. Special attention is given to the meticulous selection of factors that impact water quality, considering their advantages and limitations in the assessment. The optimization process relies on Saaty’s method of comparing individual factors and conducting a thorough multi-criteria analysis. The outcome of the analysis culminated in the development of a three-stage procedure for de-incrustation of pipeline systems. To ensure a comprehensive perspective, it is crucial to approach the entire issue in accordance with ISO 46001-compliant water management systems.


  • Open Access

    Effect of Heat Treatment on the Resulting Dimensional Characteristics of the C45 Carbon Steel after Turning

    by Jana Moravčíková, Roman Moravčík, Marián Palcut

    The presented article deals with the influence of the heat treatment of C45 steel on the surface quality after turning. Turning is a machining technology used to prepare specific geometrical characteristics of surface and dimensional quality. In the present paper, the same turning conditions were used for the turning treatment of differently heat-treated steels. The soft annealed state, normalized state, hardened state, quenched and tempered at 530 °C state and quenched and tempered at 660 °C state have been analyzed. By using this approach, it has been possible to evaluate the effects of hardening and machining on the resulting parameters after turning (roughness, cylindricity and circularity). The highest hardness was observed in the steel after the hardening process (694 ± 9 HV 10). The hardening has negatively influenced the surface quality. The high hardness was related to martensite formation and caused a damage to the cutting edge of the cut insert used, leading to a significant change in geometrical accuracy. The cylindricity change achieved 0.15 ± 0.03 mm which was significantly higher compared to the theoretical value of the diameter of the machined steel bar. An inaccuracy was also observed in diameter dimension. These inaccuracies were caused by the wear of the cutting edge of the tool used in cutting parameters setting.


  • Open Access

    Comparison of Two Laboratory-Oriented Subjects in Terms of Face-to-Face and on-Line Form of Education

    by Jana Moravčíková

    The article is focused on presenting the method of online teaching of two subjects: CAQ and Metrology and Quality of Technological Processes, which are implemented in the summer semester on Bachelor’s study degree. The teaching was to be implemented in such a way that there was interaction with the students, and, at the same time, we also had to prepare the protocols later elaborated by students. The article will compare the face-to-face method of teaching, its methods as well as the evaluation of the two subjects, with the online method of teaching. Two subjects focused on the control and measurement of dimensions will be compared, but with different ways of implementing the exercises during the online process. Both subjects used laboratories to process them. The result is a relatively comparable success in both subjects.

  • Open Access

    The Precision Analysis of Cutting Edge Preparation on CBN Cutting Inserts Using Rotary Ultrasonic Machining

    by Marcel Kuruc, Tomáš Vopát, Jana Moravčíková, Ján Milde

    This paper is focused on the issue of preparing the cutting edge microgeometry of cutting inserts made of cubic boron nitride (CBN). The aim of this research was to investigate the possibilities of rotary ultrasonic machining (RUM) for preparing asymmetric cutting edge microgeometries of various shapes (chamfers, circular, and elliptical rounding and their combinations) on a CBN cutting tool. In this article, a new type of advanced cutting edge preparation method is presented. CBN is relatively resistant to the most often used (abrasive) methods of cutting-edge preparation, due to its very high hardness (which is a prerequisite property for machining difficult-to-cut materials). Such hard materials could be processed using advanced manufacturing methods, and rotary ultrasonic machining (RUM) is one such method. Experiments have shown that RUM can be used for machining CBN. However, high hardness is not the only challenge here. For cutting edge preparation, it is necessary to achieve an adequate accuracy of size and dimensions. The presented paper analyzes the suitability of the RUM process for processing CBN inserts. The results of the experiment showed that this method can be used for preparing asymmetric cutting edge microgeometries with various shapes.


  • Open Access

    Experimental Study of Drilling Temperature, Geometrical Errors and Thermal Expansion of Drill on Hole Accuracy When Drilling CFRP/Ti Alloy Stacks

    by Vitalii Kolesnyk, Jozef Peterka, Marcel Kuruc, Vladimír Šimna, Jana Moravčíková, Tomáš Vopát, Dmytro Lisovenko

    The drilling of holes in CFRP/Ti (Carbon Fiber-Reinforced Plastic/Titanium alloy) alloy stacks is one of the frequently used mechanical operations during the manufacturing of fastening assemblies in temporary civil aircraft. A combination of inhomogeneous behavior and poor machinability of CFRP/Ti alloy stacks in one short drilling brought challenges to the manufacturing community. The impact of the drilling temperature and time delay factor under various cutting conditions on hole accuracy when machining CFRP/Ti alloy stacks is poorly studied. In this paper, the drilling temperature, the phenomenon of thermal expansion of the drill tool, and hole accuracy are investigated. An experimental study was carried out using thermocouples, the coordinate measuring machine method, and finite element analysis. The results showed that the time delay factor varied from 5 (s) to 120 (s), influences the thermal-dependent properties of CFRP, and leads to an increase in hole roundness. Additionally, the thermal expansion of the drill significantly contributes to the deviation of the hole diameter in Ti alloy.


  • Comparison of High Feed Machining with Conventional Milling in Terms of Surface Quality and Productivity

    by Marcel Kuruc, Marek Vozar, Vladimir Simna, Tomas Vopat, Jana Moravcikova, Jozef Peterka


  • Influence of Laser Surface Texturing on Tribological Performance of Tool Steels

    by Jana Moravčíková, Roman Moravčík, Martin Kusý, Martin Necpal


  • Open Access

    Analysis of the Surface Morphology of the S235JRG1 Steel After an Abrasive Water Jet Cutting Process

    by Jana Moravčíková, Daynier Rolando Delgado Sobrino, Peter Košťál

    The present paper discusses the impact of the speed of an abrasive water jet cutting process on some surface properties and morphology of the S235JRG1 steel. The values of the cutting speeds used for the analysis were of 100, 150 and 200 mm.min −1 respectively . A contact profile method was used to analyze the surface roughness during the conducted tests. In this study, the observed surface roughness parameters were the Ra, Rt and Rz, respectively. At the same time, these parameters were measured in three positions, i.e.: at the inlet (A), in the middle (B) and at the exit position (C) of the water jet nozzle with respect to the machined material. The experimental study showed that the roughness of the surface reached higher peaks and was more pronounced at the exit position (C) of the water jet. Similarly, it was also concluded that a better quality of the surface was achieved at a speed of 150 mm.min −1 .