Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Marcel Kuruc has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wire Electrode Wear in WEDM of Inconel 718: Gravimetric Evaluation Using a 33 Full Factorial Design

    by Vladimír Šimna, Marcel Kuruc, Barbora Ludrovcová, Adam Belanec, Vitalii Kolesnyk, Oleksandr Berezniak

    Wire electrical discharge machining (WEDM) is widely used for the precision cutting of difficult-to-machine materials, including nickel-based superalloys. Wire electrode wear, however, remains a practical limitation, because it affects process stability, wire consumption, and machining cost. This work examines the wear behaviour of a gamma-phase Cu5Zn8-coated copper-core wire electrode (Elecut X, ø 0.25 mm) during the WEDM of Inconel 718 using direct gravimetric measurement. A 33 full factorial experiment was carried out with three electrical parameters: pulse-on time (A), pulse-off time (B), and servo reference voltage (Aj). The discharge process was monitored with an oscilloscope so that measurements only started after the programmed pulse-off time had been reached. Electrode wear was evaluated as the mass loss Δm of 4 m wire segments after 5 min cutting intervals on a Charmilles Robofil 310 machine, and factor significance was assessed by analysis of variance (ANOVA). Pulse-on time was the dominant factor, accounting for 88.45% of the total variation in Δm, followed by servo reference voltage and pulse-off time. SEM/EDS examination showed material transfer from the Inconel 718 workpiece to the worn electrode surface, with local nickel content reaching 16.84 wt.% on the frontal face of the most worn sample. The results provide a quantitative basis for reducing wire consumption during the WEDM of Inconel 718 while recognising the trade-off with cutting productivity.

  • Open Access

    Experimental Evaluation of Flexible Fixture Stiffness for Steering Knuckles When Loading a Milling Machine Tool

    by Vitalii Kolesnyk, Marcel Kuruc, Ivan Dehtiarov, Anna Neshta, Serhii Avramenko, Vitalii Kononovych, Oksana Dynnyk, Andrii Dovhopolov, Serhii Lemekh, Roman Titskyi

    In the conditions of the increase in the range of products in the automobile and aircraft industry, there is a tendency to increase the scope of application of flexible fixtures. Thus, in the current article, it was proposed to consider a new concept of a flexible fixture for location parts of a complex shape. The stress and deflection of the steering knuckle elements were calculated using finite element modeling. During the experiment on the static loading, the deflection of the steering knuckle elements was measured, and the results of finite element modeling were validated. It was determined that the stiffness of the proposed flexible fixture ensures compliance with the tolerances of the mutual location of the surfaces of the part, making it reasonable for feature research the novel flexible fixture design during milling.


  • Open Access

    The Influence of the Setup on the Result of Measuring the Roundness of an Anuloid Surface

    by Augustín Görög, Marcel Kuruc

    In engineering practice, anuloid surfaces are produced that are subject to strict requirements in terms of accuracy (e.g., in the bearing industry). Roundness is also often measured. The accuracy of the roundness measurement does not only depend on the accuracy of a particular metrological system. The setting of the component on the measuring device can also have a significant influence on the accuracy of the measurement. The axis of the measured surface must be perpendicular to the section in which the roundness is measured. Tilting the measured surface causes a systematic measurement error, which depends on the size of the tilt angle and the parameters of the measured surface. This study presents mathematical relations for the calculation of this error when measuring roundness on an anuloid surface. Mathematical relations for the internal and external surfaces formed by the inner and outer parts of the anuloid are derived herein. There is also a theoretical analysis of the influence of inclination and the parameters of the measured surface on the size of this error. Theoretically calculated values were compared with practically measured values of roundness. The error had a negative effect on the accuracy of the roundness measurement. It affected the roundness value, the second harmonic component, and also the roundness profile itself.


  • Open Access

    The Selection of Cutting Speed to Prevent Deterioration of the Surface in Internal Turning of C45 Steel by Small-Diameter Boring Bars

    by Tomáš Vopát, Marcel Kuruc, Boris Pätoprstý, Marek Vozár, František Jurina, Barbora Bočáková, Jozef Peterka, Augustín Görög, Róbert Straka

    The turning of small-diameter deep holes is usually critical when the process of machining is unstable and the use of a special boring bar is often necessary. This paper is focused on the influence of cutting speed with a combination of cutting conditions such as feed and tool overhang on chatter marks, surface roughness and roundness of machined holes. In the experiment, two types of tool material for indexable boring bars were used, namely cemented carbide and steel. These are a group of boring bars used for the internal turning of holes of small diameters with indexable cutting inserts. Monolithic carbide boring bars are already used for internal turning of holes of even smaller diameters. Uncoated turning inserts made of cermet were used. The cutting tests were performed on the DMG CTX alpha 500 turning center. In the case of the steel boring bar, decreasing the cutting speed really led to an increase in the quality of the surface roughness and reduced the formation of chatter marks and large chatter marks. The cemented carbide boring bar also followed a similar trend, but it should be noted that the overall effect was not so great. This means that increasing the cutting speed makes the cutting process less stable and, vice versa, lower values of cutting speed reduce the formation of chatter marks and the related deterioration of the surface quality. The occurrence of chatter is directly related to the increase in the surface roughness parameters Ra and Rz of the machined surface. It can be stated that the dependence of roundness deviations on cutting speed values has a similar character to the results of the measured surface roughness values. Therefore, if the cutting speed is increased, it will make the cutting process less stable; this is also indirectly reflected in larger roundness deviations. However, it is necessary to state that this phenomenon can be observed in turning holes with small diameters using the steel boring bar, where the unstable cutting conditions materialized in the form of chatter marks.


  • Open Access

    Selected Aspects of Precision Machining on CNC Machine Tools

    by Jozef Peterka, Marcel Kuruc, Vitalii Kolesnyk, Ivan Dehtiarov, Jana Moravcikova, Tomas Vopat, Peter Pokorny, Frantisek Jurina, Vladimir Simna

    The work is new due to the type of process used—ultrasonic precision machining—to determine the possible effect of spindle heating (long-term machining) on the precision of the flat surface. It was carried out on a precise ultrasonic machining machine, and the material of workpiece was ceramic Al2O3. A flat surface was machined. Such an experiment has not been feasible until now. The experiment was divided into two days. On the first day, the machining time was 4 h. It is a long enough time to create a temperature-steady state. On the second day, with a cold tool and cold machine tool, we continued where we left off on the first day. This is how we monitored the accuracy of the dimensions of the workpiece on the plane surface. We have achieved the following: The average interface depth achieved values of 0.007089 mm and 0.003667 mm for cold and heated spindles, respectively. It means that when the spindle is not heated, the depth of the interface is higher by 93% (almost double the depth). The average standard deviation of the interface depth is 0.001683 mm and 0.000997 mm for cold and heated spindles, respectively. It means that when the spindle is not heated, the process is not as stable, and the standard deviation is higher by 69%.


  • Open Access

    The Precision Analysis of Cutting Edge Preparation on CBN Cutting Inserts Using Rotary Ultrasonic Machining

    by Marcel Kuruc, Tomáš Vopát, Jana Moravčíková, Ján Milde

    This paper is focused on the issue of preparing the cutting edge microgeometry of cutting inserts made of cubic boron nitride (CBN). The aim of this research was to investigate the possibilities of rotary ultrasonic machining (RUM) for preparing asymmetric cutting edge microgeometries of various shapes (chamfers, circular, and elliptical rounding and their combinations) on a CBN cutting tool. In this article, a new type of advanced cutting edge preparation method is presented. CBN is relatively resistant to the most often used (abrasive) methods of cutting-edge preparation, due to its very high hardness (which is a prerequisite property for machining difficult-to-cut materials). Such hard materials could be processed using advanced manufacturing methods, and rotary ultrasonic machining (RUM) is one such method. Experiments have shown that RUM can be used for machining CBN. However, high hardness is not the only challenge here. For cutting edge preparation, it is necessary to achieve an adequate accuracy of size and dimensions. The presented paper analyzes the suitability of the RUM process for processing CBN inserts. The results of the experiment showed that this method can be used for preparing asymmetric cutting edge microgeometries with various shapes.


  • Open Access

    The Influence of Cutting Parameters on Plastic Deformation and Chip Compression during the Turning of C45 Medium Carbon Steel and 62SiMnCr4 Tool Steel

    by Marcel Kuruc, Tomáš Vopát, Jozef Peterka, Martin Necpal, Vladimír Šimna, Ján Milde, František Jurina

    The paper deals with the issue of cutting zone and chip compression. The aim was to analyse the microstructure transverse section of the cutting zone on a metallographic cut, due to determined values of chip compression and plastic deformation, which affect the cutting process efficiency. The tested cutting tool material was coated with cemented carbide. The selected workpiece materials were C45 medium carbon steel of ISO grade and 62SiMnCr4 tool steel of ISO (W.Nr. 1.2101) grade. In the experiments, a DMG CTX alpha 500 turning centre was used. The cutting speed and feed were varied, and the depth of the cut was kept constant during the turning. The plastic deformation and chip compression determine the efficiency of the cutting process. The higher compression requires more work to perform the process and, therefore, it requires more energy for doing so. With the increase of the cutting speed, the deformation for C45 steel is decreased. The rapid deformation reduction was observed when the cutting speed was increased from 145 m/min to 180 m/min. Generally, deformation is decreasing with the increase of the feed. Only at a cutting speed of 145 m/min was the deformation elevation observed, when the feed was increased from 0.4 mm to 0.6 mm. During the turning of the 62SiMnCr4 tool steel we observed an error value at a cutting speed of 145 m/min and a feed of 0.4 mm was the middle cutting parameter. However, feed dependence was clear: With an increase of the feed, the plastic deformation was decreasing. This decreasing was more rapid with the increasing of the cutting speed. Besides plastic deformation, there was analysed chip compression as well. With the increasing of the cutting speed, there was a decrease of the chip compression. Due to a lack of information in the area of the chip compression and the plastic deformation in the cutting process, we decided to investigate the cutting zone for the turning of tool steels 62SiMnCr4, which was compared with the reference steel C45. The results could be applied to increase the efficiency of the process and improvement of the surface integrity.


  • Open Access

    Behavior of Rotary Ultrasonic Machining of Ceramic Materials at a Wide Range of Cutting Speeds

    by Marcel Kuruc, Jozef Peterka

    The paper deals with the behavior of the rotary ultrasonic machining process at different cutting speeds of ceramic materials. This process is relatively new; therefore, there are gaps in information about its behavior at near-critical parameters. We adjusted cutting speeds 10 times lower and 10 times higher than the recommended one. The observed parameters were machine load, tool wear, and surface roughness. Alumina and zirconia ceramics were used as materials. The results will help with the optimization of the cutting parameters of the rotary ultrasonic machining process.


  • Introduction

    by Marcel Kuruc