JMJens Martin

Jens Martin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jens Martin has a total of 72 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    X-ray reciprocal space imaging of a screw-dislocation network at a low-angle twist boundary in a SrTiO 3 membrane transfer-bonded to bulk SrTiO 3

    by Jeremy Maltitz, Martin Schmidbauer, Carsten Richter, Michael Hanke, Ferris Stümpel, Thomas Schroeder, Jutta Schwarzkopf, Jens Martin

    The transfer of oxide membranes provides a new dimension in material design that goes beyond the limitations of classical hetero-epitaxy. For example, the transfer of freestanding membranes offers the in-plane twist angle between film and substrate as a tuneable degree of freedom. An ideal twist boundary yields formation of an in-plane screw-dislocation network to reduce interfacial stress. Previously, periodic screw-dislocation networks have been demonstrated by wafer bonding of two crystals, where the twist boundary is embedded in the bulk and made accessible to detailed characterization mostly by destructive methods. Recent approaches exploited freestanding membranes to create twist boundaries with the interface located only nanometers beneath the surface, making it readily accessible by near-surface-sensitive techniques. In this work, both approaches were combined to transfer membranes on the mm²-scale via wafer bonding and subsequent release by etching the sacrificial layer. High-resolution synchrotron-based grazing incidence x-ray diffraction was performed to investigate the structure of the twisted SrTiO 3 / SrTiO 3 interface. In order to gain a better qualitative and quantitative understanding of the experimental results, we simulated the x-ray diffraction of twisted perovskites based on continuum elastic theory and kinematical scattering. Our measurements show that the measured diffraction patterns are consistent with the formation of a periodic screw-dislocation network, since the apparent superlattice reflections coincide with the obtained diffraction pattern from simulations. However, the intensity profile and appearance of specific symmetry-forbidden diffraction peaks in the experiments cannot be described by elastic displacements alone.

  • Open Access

    CuInSe2-based micro-concentrator solar cells fabricated from In islands grown by laser-assisted MO-CVD

    by J. Berger, S. Zahedi-Azad, H. Voss, O.C. Ernst, R. Hammerschmidt, T. Boeck, J. Martin, J. Bonse, J. Krüger, M. Schmid

  • Open Access

    Chemical vapor deposition of indium precursors for solar micro-absorbers using continuous laser radiation

    by Heike Voss, Setareh Zahedi-Azad, Owen C. Ernst, Jan Lucaßen, Guido Mann, Jörn Bonse, Torsten Boeck, Jens Martin, Martina Schmid, Jörg Krüger

    Localized deposition of indium on an amorphous glass surface covered with a thin molybdenum layer is demonstrated utilizing laser-assisted chemical vapor deposition. A continuous-wave laser causes a temperature rise on the molybdenum layer resulting in the selective aggregation of liquid and ultimately crystalline structures of indium. The formation sites of the indium are determined by the decomposition of gaseous trimethylindium. The deposited indium islands can serve as precursors and could be further processed into compound semiconductors like CuInSe 2 for micro-concentrator solar cells. The experimental investigations were supported by theoretical simulations of the laser heating process to calculate the local temperature distribution on the surface of the molybdenum-covered glass substrate.


  • Resistively detected electron spin resonance and g-factor in few-layer exfoliated MoS2 devices

    by Chithra H Sharma, Appanna Parvangada, Lars Tiemann, Kai Rossnagel, Jens Martin, Robert H Blick

    MoS2 has recently emerged as a promising material for enabling quantum devices and spintronic applications. In this context, an improved physical understanding of the g-factor of MoS2 depending on device geometry is of great importance. Resistively detected electron spin resonance (RD-ESR) could be employed to determine the g-factor in micron-scale devices. However, its application and RD-ESR studies have been limited by Schottky or high-resistance contacts to MoS2. Here, we exploit naturally n-doped few-layer MoS2 devices with ohmic tin (Sn) contacts that allow the electrical study of spin phenomena. Resonant excitation of electron spins and resistive detection is a possible path to exploit the spin effects in MoS2 devices. Using RD-ESR, we determine the g-factor of few-layer MoS2 to be ∼1.92 and observe that the g-factor value is independent of the charge carrier density within the limits of our measurements.


  • Open Access

    Periodic lateral superlattice in bonded SrTiO3/SrTiO3 twisted perovskites

    by M. Schmidbauer, J. Maltitz, F. Stümpel, M. Hanke, C. Richter, J. Schwarzkopf, J. Martin

    Stacking of freestanding membranes enables the formation of interfaces beyond what can be obtained with classical heteroepitaxy. In particular, twisted interfaces provide unique physical properties not existent in the corresponding individual layers. An ideal twist grain boundary yields an in-plane screw-dislocation network, assuming sufficiently strong interactions across the interface, for example, via covalent or ionic bonding. Hereby, the distance between dislocation lines, that is the length scale of the Moiré pattern, is set by the twist angle between the adjacent crystalline surfaces and the lattice mismatch in case that different materials are placed together. The associated strain gradients of the periodic pattern are especially appealing for oxide-based perovskites due to the intricate connection between surface polarization and subtle structural deformations such as the oxygen octahedra tilt. Recently, freestanding oxide perovskites became available via the sacrificial layer approach, opening a pathway toward oxide-based Moiré materials. Here, we demonstrate efficient bonding of a freestanding SrTiO3 layer to a SrTiO3 single-crystal by initially conducting a wafer-bonding process at high temperature and only subsequently dissolving the sacrificial layer. We investigate the twisted SrTiO3/SrTiO3 interface with x-ray diffraction in grazing incidence geometry and observe clear signatures of a highly periodic lateral superlattice consistent with the formation of a screw-dislocation network. Our work demonstrates a robust route for the fabrication of twisted perovskites and their development into a functional material platform with designed strain gradients at the nanoscale.


  • Open Access

    Preparation and Investigation of Micro-Transfer-Printable Single-Crystalline InP Coupons for Heterogeneous Integration of III-V on Si

    by Isabella Peracchi, Carsten Richter, Tobias Schulz, Jens Martin, Albert Kwasniewski, Sebastian Kläger, Christiane Frank-Rotsch, Patrick Steglich, Karoline Stolze

    New requirements for high-frequency applications in wireless communication and sensor technologies need III-V compound semiconductors such as indium phosphide (InP) to complement silicon (Si)-based technologies. This study establishes the basis for a new approach to heterogeneous integration of III-V on Si aimed at the transfer of single-crystalline InP coupons on Si via micro-transfer printing (μTP). The InP coupons will act as high-quality virtual substrates that allow selective homo-epitaxy. We present the chemical-mechanical polishing-based preparation and structural characterization of µm-thin (001) InP platelets, starting from high-quality 4-inch bulk crystals and micro-patterning into transferable coupons of several hundred µm2. The obtained InP platelets exhibit the desired thickness—below 10 ± 1 µm—and low surface roughness—<0.3 nm—on both sides, meeting the precondition for µTP and epitaxy. X-ray rocking curve measurements provide accurate spatial maps of the total strain, which indicate small strain variations in the µm-thin InP sample. Rocking curve mappings of the (0 0 4) reflection reveal half-widths below 16 arcsec in the majority of the sample area after thinning that is similar to commercially available InP bulk substrates. Pole figure measurements show no evidence of stress-induced micro-twinning or stacking faults. Overall, minor indications of crystal quality degradation in the product platelets, compared with the bulk samples, were detected.


  • Open Access

    Author Correction: Charge disproportionate molecular redox for discrete memristive and memcapacitive switching

    by Santi P. Rath, Damien Thompson, Svante Hedström, Meenakshi Annamalai, Rajib Pramanick, B. Robert Ilic, Soumya Sarkar, Sonu Hooda, Christian A. Nijhuis, Jens Martin, et al.


  • Transfer Printable Single-Crystalline Coupons for III-V on Si Integration

    by Sebastian Daszko, Carsten Richter, Jens Martin, Katrin Berger, Uta Juda, Christiane Frank-Rotsch, Patrick Steglich, Karoline Stolze

    The next-generation internet (6G) requires highly functional devices that e.g. realize frequencies in the THz range for higher data rates and lower latencies. Those requirements exceed the physical limits of established CMOS technologies based on silicon (Si). Hence, there is demand for other semiconductor materials with superior electronic and optical properties that complement Si. One of the key candidates is the III-V compound semiconductor, indium phosphide (InP). Due to its high electron mobility and direct band gap, InP-based devices allow access to frequencies >100 GHz and operate at the optical fibre compatible wavelength of 1.55 μm.1 With the perspective of leveraging the advantages of Si-based CMOS technology and III-V semiconductors, hetero-integration of III-V materials on Si is of great interest. However, existing integration approaches entail certain disadvantages: (i) High dislocation densities due to the lattice mismatch of InP and Si for integration via hetero-epitaxial growth;2 (ii) limited integration density and the requirement of accurate alignment for flip-chip integration; and (iii) high process-related losses of Si and III-V materials as well as thermal stress and low thermal conductivity of adhesive layers degrading device performance for wafer/die bonding technologies.3 Another promising approach for III-V-on-Si integration is micro-transfer-printing (μTP) that involves pick-up and transfer of µm-small chips from a source substrate to a target substrate with high alignment accuracy by using an elastomeric stamp. Advantages of μTP are high integration densities and efficient material use. The technique was already implemented for III-V-on-Si photonic integrated circuits by transfer of epitaxial III-V layers.4 However, using sacrificial III-V interlayers for release and adhesives for bonding still leads to transfer issues and low operation temperature for the devices, respectively. We pursue a new approach to hetero-integration of III-V on Si that aims at the transfer of single-crystalline InP coupons onto Si via μTP. This will be achieved by obtaining crystalline coupons with a thickness of d ≤ 10 µm and two polished surfaces that attain low roughness, needed i.a. for µTP. If the high structural quality of the single-crystalline InP source material can be maintained, this process will provide high quality templates for subsequent epitaxial growth. Towards this goal, we developed a sophisticated micro-preparation process in cooperation with the Leibniz Institute for High Performance Microelectronics IHP.5 Starting from 4-inch single crystals with homogeneous, low dislocation density of 2×103 cm- 2 grown at IKZ,6 thinned InP dies were obtained by sawing, grinding and employing an optimized two-step chemical mechanical polishing (CMP). In order to produce µm-sized transfer-printable coupons, the InP dies were micro structured by means of photolithography assisted patterning and wet (under-)etching (Fig. 1). The coupons can then be picked up with a stamp and transferred to the target wafer. Main innovation of this process is the resin which serves as low stress fixing layer for CMP as well as sacrificial layer for later release. The optimized CMP process with abrasive-free final polishing yielded InP platelets of the desired thickness below 10 μm with low thickness deviation < 1 µm and excellent surface roughness of S q ≈ 0.3 nm (Fig. 2a,b,d). This value even meets the requirements for adhesive-free bonding (S q ≤ 2 nm) and subsequent epitaxial growth (S q ≤ 0.5 nm). X-ray rocking curve mapping provides accurate spatial maps of lattice deformations in the material that may be a consequence of the mechanical processing. Rocking curve widths mappings of the 004 reflection of a (001) sample before and after thinning are homogeneous and below 25 arcsec in the majority of the sample area. Overall no signs of systematic crystal quality deterioration in the product platelets compared to bulk samples have been detected. In summary, the feasibility of μm-thin InP platelet fabrication was demonstrated. Final platelets meet the prerequisites of low and uniform thickness, high planarity, low roughness and little crystal quality deterioration. Furthermore, first InP platelets could successfully be patterned to 100–400 µm-sized coupons using optical lithography and wet etching (Fig. 2c). This opens a path to take the next steps towards hetero-integration on Si by means of µTP with high potential for adhesive-free bonding. References [1] J. C. Rode, et al. IEEE Trans. Electron Devices 2015, 62, 2779–2785. [2] Q. Li, K. M. Lau Prog. Cryst. Growth Charact. Mater. 2017, 63, 105–120. [3] X. Guo, et al. J. Semicond. 2019, 40, 101304. [4] J. Zhang, et al. APL Photonics 2019, 4, 110803. [5] IKZ-IHP Patent filed - DE 10 2022 100 661.1. [6] K. Giziewicz, et al. 51st Annual Meeting of the German Association of Crystal Growth, 2021, Berlin. Figure 1

  • Open Access

    Modulation of Spin Dynamics in 2D Transition‐Metal Dichalcogenide via Strain‐Driven Symmetry Breaking

    by Tao Liu, Du Xiang, Hong Kuan Ng, Zichao Han, Kedar Hippalgaonkar, Ady Suwardi, Jens Martin, Slaven Garaj, Jing Wu

    Transition metal dichalcogenides (TMDs) possess intrinsic spin–orbit interaction (SOI) with high potential to be exploited for various quantum phenomena. SOI allows the manipulation of spin degree of freedom by controlling the carrier's orbital motion via mechanical strain. Here, strain modulated spin dynamics in bilayer MoS2 field‐effect transistors (FETs) fabricated on crested substrates are demonstrated. Weak antilocalization (WAL) is observed at moderate carrier concentrations, indicating additional spin relaxation path caused by strain fields arising from substrate crests. The spin lifetime is found to be inversely proportional to the momentum relaxation time, which follows the Dyakonov–Perel spin relaxation mechanism. Moreover, the spin–orbit splitting is obtained as 37.5 ± 1.4 meV, an order of magnitude larger than the theoretical prediction for monolayer MoS2, suggesting the strain enhanced spin‐lattice coupling. The work demonstrates strain engineering as a promising approach to manipulate spin degree of freedom toward new functional quantum devices.


  • Open Access

    Biomolecular control over local gating in bilayer graphene induced by ferritin

    by Senthil Kumar Karuppannan, Jens Martin, Wentao Xu, Rupali Reddy Pasula, Sierin Lim, Christian A. Nijhuis