CFChristiane Frank-Rotsch

Christiane Frank-Rotsch

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Christiane Frank-Rotsch has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • 15.3% AM1.5G Efficiency GaAs Solar Cells Fabricated via an Epitaxy-Free Process

    by Phillip R. Jahelka, Aaron J. Ptak, John Simon, Kevin L. Schulte, Frank M. Kiessling, Christiane Frank-Rotsch, Susana Torres-Londono, Harry A. Atwater

  • Open Access

    Preparation and Investigation of Micro-Transfer-Printable Single-Crystalline InP Coupons for Heterogeneous Integration of III-V on Si

    by Isabella Peracchi, Carsten Richter, Tobias Schulz, Jens Martin, Albert Kwasniewski, Sebastian Kläger, Christiane Frank-Rotsch, Patrick Steglich, Karoline Stolze

    New requirements for high-frequency applications in wireless communication and sensor technologies need III-V compound semiconductors such as indium phosphide (InP) to complement silicon (Si)-based technologies. This study establishes the basis for a new approach to heterogeneous integration of III-V on Si aimed at the transfer of single-crystalline InP coupons on Si via micro-transfer printing (μTP). The InP coupons will act as high-quality virtual substrates that allow selective homo-epitaxy. We present the chemical-mechanical polishing-based preparation and structural characterization of µm-thin (001) InP platelets, starting from high-quality 4-inch bulk crystals and micro-patterning into transferable coupons of several hundred µm2. The obtained InP platelets exhibit the desired thickness—below 10 ± 1 µm—and low surface roughness—<0.3 nm—on both sides, meeting the precondition for µTP and epitaxy. X-ray rocking curve measurements provide accurate spatial maps of the total strain, which indicate small strain variations in the µm-thin InP sample. Rocking curve mappings of the (0 0 4) reflection reveal half-widths below 16 arcsec in the majority of the sample area after thinning that is similar to commercially available InP bulk substrates. Pole figure measurements show no evidence of stress-induced micro-twinning or stacking faults. Overall, minor indications of crystal quality degradation in the product platelets, compared with the bulk samples, were detected.


  • Transfer Printable Single-Crystalline Coupons for III-V on Si Integration

    by Sebastian Daszko, Carsten Richter, Jens Martin, Katrin Berger, Uta Juda, Christiane Frank-Rotsch, Patrick Steglich, Karoline Stolze

    The next-generation internet (6G) requires highly functional devices that e.g. realize frequencies in the THz range for higher data rates and lower latencies. Those requirements exceed the physical limits of established CMOS technologies based on silicon (Si). Hence, there is demand for other semiconductor materials with superior electronic and optical properties that complement Si. One of the key candidates is the III-V compound semiconductor, indium phosphide (InP). Due to its high electron mobility and direct band gap, InP-based devices allow access to frequencies >100 GHz and operate at the optical fibre compatible wavelength of 1.55 μm.1 With the perspective of leveraging the advantages of Si-based CMOS technology and III-V semiconductors, hetero-integration of III-V materials on Si is of great interest. However, existing integration approaches entail certain disadvantages: (i) High dislocation densities due to the lattice mismatch of InP and Si for integration via hetero-epitaxial growth;2 (ii) limited integration density and the requirement of accurate alignment for flip-chip integration; and (iii) high process-related losses of Si and III-V materials as well as thermal stress and low thermal conductivity of adhesive layers degrading device performance for wafer/die bonding technologies.3 Another promising approach for III-V-on-Si integration is micro-transfer-printing (μTP) that involves pick-up and transfer of µm-small chips from a source substrate to a target substrate with high alignment accuracy by using an elastomeric stamp. Advantages of μTP are high integration densities and efficient material use. The technique was already implemented for III-V-on-Si photonic integrated circuits by transfer of epitaxial III-V layers.4 However, using sacrificial III-V interlayers for release and adhesives for bonding still leads to transfer issues and low operation temperature for the devices, respectively. We pursue a new approach to hetero-integration of III-V on Si that aims at the transfer of single-crystalline InP coupons onto Si via μTP. This will be achieved by obtaining crystalline coupons with a thickness of d ≤ 10 µm and two polished surfaces that attain low roughness, needed i.a. for µTP. If the high structural quality of the single-crystalline InP source material can be maintained, this process will provide high quality templates for subsequent epitaxial growth. Towards this goal, we developed a sophisticated micro-preparation process in cooperation with the Leibniz Institute for High Performance Microelectronics IHP.5 Starting from 4-inch single crystals with homogeneous, low dislocation density of 2×103 cm- 2 grown at IKZ,6 thinned InP dies were obtained by sawing, grinding and employing an optimized two-step chemical mechanical polishing (CMP). In order to produce µm-sized transfer-printable coupons, the InP dies were micro structured by means of photolithography assisted patterning and wet (under-)etching (Fig. 1). The coupons can then be picked up with a stamp and transferred to the target wafer. Main innovation of this process is the resin which serves as low stress fixing layer for CMP as well as sacrificial layer for later release. The optimized CMP process with abrasive-free final polishing yielded InP platelets of the desired thickness below 10 μm with low thickness deviation < 1 µm and excellent surface roughness of S q ≈ 0.3 nm (Fig. 2a,b,d). This value even meets the requirements for adhesive-free bonding (S q ≤ 2 nm) and subsequent epitaxial growth (S q ≤ 0.5 nm). X-ray rocking curve mapping provides accurate spatial maps of lattice deformations in the material that may be a consequence of the mechanical processing. Rocking curve widths mappings of the 004 reflection of a (001) sample before and after thinning are homogeneous and below 25 arcsec in the majority of the sample area. Overall no signs of systematic crystal quality deterioration in the product platelets compared to bulk samples have been detected. In summary, the feasibility of μm-thin InP platelet fabrication was demonstrated. Final platelets meet the prerequisites of low and uniform thickness, high planarity, low roughness and little crystal quality deterioration. Furthermore, first InP platelets could successfully be patterned to 100–400 µm-sized coupons using optical lithography and wet etching (Fig. 2c). This opens a path to take the next steps towards hetero-integration on Si by means of µTP with high potential for adhesive-free bonding. References [1] J. C. Rode, et al. IEEE Trans. Electron Devices 2015, 62, 2779–2785. [2] Q. Li, K. M. Lau Prog. Cryst. Growth Charact. Mater. 2017, 63, 105–120. [3] X. Guo, et al. J. Semicond. 2019, 40, 101304. [4] J. Zhang, et al. APL Photonics 2019, 4, 110803. [5] IKZ-IHP Patent filed - DE 10 2022 100 661.1. [6] K. Giziewicz, et al. 51st Annual Meeting of the German Association of Crystal Growth, 2021, Berlin. Figure 1

  • Toward Model-Based Control of the Vertical Gradient Freeze Crystal Growth Process

    by Stefan Ecklebe, Frank Woittennek, Christiane Frank-Rotsch, Natasha Dropka, Jan Winkler

    In this contribution, tracking control designs using output feedback are presented for a two-phase Stefan problem (SP) arising in the modeling of the vertical gradient freeze process. The two-phase SP, consisting of two coupled free boundary problems, is a vital part of many crystal growth processes due to the temporally varying spatial extent of the solid and liquid domains during growth. After discussing the special needs of the process, collocated and flatness-based state feedback designs are carried out. The quality of the provided approximations and the performance and robustness against parameter uncertainties of the open- and closed-loop control setups are analyzed in several simulations.


  • Open Access

    Semiconductor Crystal Growth under the Influence of Magnetic Fields

    by Christiane Frank‐Rotsch, Natasha Dropka, Frank‐Michael Kießling, Peter Rudolph

    The recent development of semiconductor crystal growth focusses on increase of process efficiency and simultaneous improvement of crystal quality. For improved crystal quality, an exact and permanent control of the melt flow is a crucial parameter. To achieve larger crystals, the melt volume must be increased markedly resulting in disadvantageously changed melt convection. In the case of Czochralski growth, the flow can even become turbulent. This changed flow can disturb the single crystal growth and may give rise to dopant inhomogeneities within the crystal. To effectively influence melt flow and hence to improve growth conditions, magnetic fields can be applied. Mostly, steady magnetic fields (SMF) are applied in industrial scale to damp melt flow oscillations. However, compared to SMF the application of non‐SMF proves to be also very promising since significantly lower induction causes similar effects in the melt. An overview on magnetic field features with the focus on achievable results under the influence of traveling magnetic fields is given.