Teresa Brecht
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Teresa Brecht has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Aaron M. Jones
HRL Laboratories, LLC, 3011 Malibu Canyon Road, Malibu, California 90265, USA
3 shared publications - Chen Wang
University of Massachusetts-Amherst
3 shared publications - Jacob Z. Blumoff
HRL Laboratories, LLC
3 shared publications - Luigi Frunzio
Yale University
3 shared publications - Matthew G. Borselli
HRL Laboratories, LLC
3 shared publications Matthew T. Rakher
HRL Laboratories, LLC
3 shared publications
Latest Publications
- Open Access
- 11 June 2024
- Published by American Physical Society (APS) in PRX Quantum
- Vol. 5 (2) , 020356
Full-Permutation Dynamical Decoupling in Triple-Quantum-Dot Spin Qubits
Dynamical decoupling of spin qubits in silicon can increase fidelity and can be used to extract the frequency spectra of noise processes. We demonstrate a full-permutation dynamical decoupling technique that cyclically exchanges the spins in a triple-quantum-dot qubit. This sequence not only suppresses both low-frequency charge-noise-induced and magnetic-noise-induced errors; it also refocuses leakage errors to first order, which is particularly interesting for encoded exchange-only qubits. For a specific construction, which we call “NZ1y,” the qubit is isolated from error sources to such a degree that we measure a remarkable exchange pulse error of . This sequence maintains a quantum state for roughly 18,000 exchange pulses, extending the qubit coherence from to . We experimentally validate an error model that includes charge noise and magnetic noise in two ways: by direct exchange-qubit simulation and by integration of the assumed noise spectra with derived filter functions, both of which reproduce the measured error and leakage with respect to a change of the repetition rate.- 11 June 2024
- Published by American Physical Society (APS) in PRX Quantum
- Vol. 5 (2) , 020356
Open AccessFull-Permutation Dynamical Decoupling in Triple-Quantum-Dot Spin Qubits
Dynamical decoupling of spin qubits in silicon can increase fidelity and can be used to extract the frequency spectra of noise processes. We demonstrate a full-permutation dynamical decoupling technique that cyclically exchanges the spins in a triple-quantum-dot qubit. This sequence not only suppresses both low-frequency charge-noise-induced and magnetic-noise-induced errors; it also refocuses leakage errors to first order, which is particularly interesting for encoded exchange-only qubits. For a specific construction, which we call “NZ1y,” the qubit is isolated from error sources to such a degree that we measure a remarkable exchange pulse error of . This sequence maintains a quantum state for roughly 18,000 exchange pulses, extending the qubit coherence from to . We experimentally validate an error model that includes charge noise and magnetic noise in two ways: by direct exchange-qubit simulation and by integration of the assumed noise spectra with derived filter functions, both of which reproduce the measured error and leakage with respect to a change of the repetition rate. - Open Access
Full-permutation dynamical decoupling in triple-quantum-dot spin qubits
Dynamical decoupling of spin qubits in silicon can enhance fidelity and be used to extract the frequency spectra of noise processes. We demonstrate a full-permutation dynamical decoupling technique that cyclically exchanges the spins in a triple-dot qubit. This sequence not only suppresses both low frequency charge-noise- and magnetic-noise-induced errors; it also refocuses leakage errors to first order, which is particularly interesting for encoded exchange-only qubits. For a specific construction, which we call NZ1y, the qubit is isolated from error sources to such a degree that we measure a remarkable exchange pulse error of $5\times10^{-5}$. This sequence maintains a quantum state for roughly 18,000 exchange pulses, extending the qubit coherence from $T_2^*=2~\mu$s to $T_2 = 720~\mu$s. We experimentally validate an error model that includes $1/f$ charge noise and $1/f$ magnetic noise in two ways: by direct exchange-qubit simulation, and by integration of the assumed noise spectra with derived filter functions, both of which reproduce the measured error and leakage with respect to changing the repetition rate.Open AccessFull-permutation dynamical decoupling in triple-quantum-dot spin qubits
Dynamical decoupling of spin qubits in silicon can enhance fidelity and be used to extract the frequency spectra of noise processes. We demonstrate a full-permutation dynamical decoupling technique that cyclically exchanges the spins in a triple-dot qubit. This sequence not only suppresses both low frequency charge-noise- and magnetic-noise-induced errors; it also refocuses leakage errors to first order, which is particularly interesting for encoded exchange-only qubits. For a specific construction, which we call NZ1y, the qubit is isolated from error sources to such a degree that we measure a remarkable exchange pulse error of $5\times10^{-5}$. This sequence maintains a quantum state for roughly 18,000 exchange pulses, extending the qubit coherence from $T_2^*=2~\mu$s to $T_2 = 720~\mu$s. We experimentally validate an error model that includes $1/f$ charge noise and $1/f$ magnetic noise in two ways: by direct exchange-qubit simulation, and by integration of the assumed noise spectra with derived filter functions, both of which reproduce the measured error and leakage with respect to changing the repetition rate. - Open Access
- 29 March 2022
- Published by American Physical Society (APS) in PRX Quantum
- Vol. 3 (1) , 010352
Fast and High-Fidelity State Preparation and Measurement in Triple-Quantum-Dot Spin Qubits
We demonstrate rapid high-fidelity state preparation and measurement in exchange-only / triple-quantum-dot qubits. Fast measurement integration (980-ns) and initialization (approximately 300-ns) operations are performed with all-electrical baseband control. We emphasize a leakage-sensitive joint initialization and measurement metric, developed in the context of exchange-only qubits but applicable more broadly, and report an infidelity of . This result is enabled by a high-valley-splitting heterostructure, initialization at the two- to three-electron charge boundary, and careful assessment and mitigation of during spin-to-charge conversion. The ultimate fidelity is limited by a number of comparably important factors and we identify clear paths toward further improved fidelity and speed. Along with an observed single-qubit randomized benchmarking error rate of , this work demonstrates initialization, control, and measurement of / triple-dot qubits at fidelities and durations that are promising for scalable quantum information processing.- 29 March 2022
- Published by American Physical Society (APS) in PRX Quantum
- Vol. 3 (1) , 010352
Open AccessFast and High-Fidelity State Preparation and Measurement in Triple-Quantum-Dot Spin Qubits
We demonstrate rapid high-fidelity state preparation and measurement in exchange-only / triple-quantum-dot qubits. Fast measurement integration (980-ns) and initialization (approximately 300-ns) operations are performed with all-electrical baseband control. We emphasize a leakage-sensitive joint initialization and measurement metric, developed in the context of exchange-only qubits but applicable more broadly, and report an infidelity of . This result is enabled by a high-valley-splitting heterostructure, initialization at the two- to three-electron charge boundary, and careful assessment and mitigation of during spin-to-charge conversion. The ultimate fidelity is limited by a number of comparably important factors and we identify clear paths toward further improved fidelity and speed. Along with an observed single-qubit randomized benchmarking error rate of , this work demonstrates initialization, control, and measurement of / triple-dot qubits at fidelities and durations that are promising for scalable quantum information processing. - Top Cited Papers
- 1 September 2020
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 91 (9) , 091101
Materials loss measurements using superconducting microwave resonators
The performance of superconducting circuits for quantum computing is limited by materials losses. In particular, coherence times are typically bounded by two-level system (TLS) losses at single photon powers and millikelvin temperatures. The identification of low loss fabrication techniques, materials, and thin film dielectrics is critical to achieving scalable architectures for superconducting quantum computing. Superconducting microwave resonators provide a convenient qubit proxy for assessing performance and studying TLS loss and other mechanisms relevant to superconducting circuits such as non-equilibrium quasiparticles and magnetic flux vortices. In this review article, we provide an overview of considerations for designing accurate resonator experiments to characterize loss, including applicable types of losses, cryogenic setup, device design, and methods for extracting material and interface losses, summarizing techniques that have been evolving for over two decades. Results from measurements of a wide variety of materials and processes are also summarized. Finally, we present recommendations for the reporting of loss data from superconducting microwave resonators to facilitate materials comparisons across the field.
- 1 September 2020
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 91 (9) , 091101
Top Cited PapersMaterials loss measurements using superconducting microwave resonators
The performance of superconducting circuits for quantum computing is limited by materials losses. In particular, coherence times are typically bounded by two-level system (TLS) losses at single photon powers and millikelvin temperatures. The identification of low loss fabrication techniques, materials, and thin film dielectrics is critical to achieving scalable architectures for superconducting quantum computing. Superconducting microwave resonators provide a convenient qubit proxy for assessing performance and studying TLS loss and other mechanisms relevant to superconducting circuits such as non-equilibrium quasiparticles and magnetic flux vortices. In this review article, we provide an overview of considerations for designing accurate resonator experiments to characterize loss, including applicable types of losses, cryogenic setup, device design, and methods for extracting material and interface losses, summarizing techniques that have been evolving for over two decades. Results from measurements of a wide variety of materials and processes are also summarized. Finally, we present recommendations for the reporting of loss data from superconducting microwave resonators to facilitate materials comparisons across the field.
- 12 September 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (11) , 112601
Suspending superconducting qubits by silicon micromachining
We present a method for relieving aluminum 3D transmon qubits from a silicon substrate using micromachining. Our technique is a high yield, one-step deep reactive ion etch that requires no additional fabrication processes and results in the suspension of the junction area and edges of the aluminum film. The drastic change in the device geometry affects both the dielectric and the flux noise environment experienced by the qubit. In particular, the participation ratios of various dielectric interfaces are significantly modified, and suspended qubits exhibited longer T1's than non-suspended ones. We also find that the suspension increases the flux noise experienced by tunable SQUID-based qubits.
- 12 September 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (11) , 112601
Suspending superconducting qubits by silicon micromachining
We present a method for relieving aluminum 3D transmon qubits from a silicon substrate using micromachining. Our technique is a high yield, one-step deep reactive ion etch that requires no additional fabrication processes and results in the suspension of the junction area and edges of the aluminum film. The drastic change in the device geometry affects both the dielectric and the flux noise environment experienced by the qubit. In particular, the participation ratios of various dielectric interfaces are significantly modified, and suspended qubits exhibited longer T1's than non-suspended ones. We also find that the suspension increases the flux noise experienced by tunable SQUID-based qubits.
- Open Access
- 9 November 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (19) , 192603
Demonstration of superconducting micromachined cavities
Superconducting enclosures will be key components of scalable quantum computing devices based on circuit quantum electrodynamics. Within a densely integrated device, they can protect qubits from noise and serve as quantum memory units. Whether constructed by machining bulk pieces of metal or microfabricating wafers, 3D enclosures are typically assembled from two or more parts. The resulting seams potentially dissipate crossing currents and limit performance. In this letter, we present measured quality factors of superconducting cavity resonators of several materials, dimensions, and seam locations. We observe that superconducting indium can be a low-loss RF conductor and form low-loss seams. Leveraging this, we create a superconducting micromachined resonator with indium that has a quality factor of two million, despite a greatly reduced mode volume. Inter-layer coupling to this type of resonator is achieved by an aperture located under a planar transmission line. The described techniques demonstrate a proof-of-principle for multilayer microwave integrated quantum circuits for scalable quantum computing.
- 9 November 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (19) , 192603
Open AccessDemonstration of superconducting micromachined cavities
Superconducting enclosures will be key components of scalable quantum computing devices based on circuit quantum electrodynamics. Within a densely integrated device, they can protect qubits from noise and serve as quantum memory units. Whether constructed by machining bulk pieces of metal or microfabricating wafers, 3D enclosures are typically assembled from two or more parts. The resulting seams potentially dissipate crossing currents and limit performance. In this letter, we present measured quality factors of superconducting cavity resonators of several materials, dimensions, and seam locations. We observe that superconducting indium can be a low-loss RF conductor and form low-loss seams. Leveraging this, we create a superconducting micromachined resonator with indium that has a quality factor of two million, despite a greatly reduced mode volume. Inter-layer coupling to this type of resonator is achieved by an aperture located under a planar transmission line. The described techniques demonstrate a proof-of-principle for multilayer microwave integrated quantum circuits for scalable quantum computing.
- Top Cited Papers
- 19 October 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (16) , 162601
Surface participation and dielectric loss in superconducting qubits
We study the energy relaxation times (T1) of superconducting transmon qubits in 3D cavities as a function of dielectric participation ratios of material surfaces. This surface participation ratio, representing the fraction of electric field energy stored in a dissipative surface layer, is computed by a two-step finite-element simulation and experimentally varied by qubit geometry. With a clean electromagnetic environment and suppressed non-equilibrium quasiparticle density, we find an approximately proportional relation between the transmon relaxation rates and surface participation ratios. These results suggest dielectric dissipation arising from material interfaces is the major limiting factor for the T1 of transmons in 3D circuit quantum electrodynamics architecture. Our analysis also supports the notion of spatial discreteness of surface dielectric dissipation.
- 19 October 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (16) , 162601
Top Cited PapersSurface participation and dielectric loss in superconducting qubits
We study the energy relaxation times (T1) of superconducting transmon qubits in 3D cavities as a function of dielectric participation ratios of material surfaces. This surface participation ratio, representing the fraction of electric field energy stored in a dissipative surface layer, is computed by a two-step finite-element simulation and experimentally varied by qubit geometry. With a clean electromagnetic environment and suppressed non-equilibrium quasiparticle density, we find an approximately proportional relation between the transmon relaxation rates and surface participation ratios. These results suggest dielectric dissipation arising from material interfaces is the major limiting factor for the T1 of transmons in 3D circuit quantum electrodynamics architecture. Our analysis also supports the notion of spatial discreteness of surface dielectric dissipation.