Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Puqing Jiang has a total of 85 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A transfer-learning-enhanced reduced-order surrogate for rapid thermal property extraction in patterned FDTR

    by Bingjia Xiao, Tao Chen, Puqing Jiang

    Patterned-transducer frequency-domain thermoreflectance (FDTR) enhances sensitivity to low-thermal-conductivity materials by suppressing lateral heat spreading within the metal transducer. However, the finite patterned geometry is not directly described by conventional analytical models formulated for laterally unbounded transducers, making iterative parameter fitting based on finite-element simulations computationally prohibitive. Here, we develop a reduced-order surrogate model, enhanced by transfer learning, that directly predicts the FDTR phase response for rapid inverse thermal-property extraction. Within the original training domain, the surrogate achieves a mean phase root mean square error of 0.19° relative to the full-order comsol simulations and accelerates forward prediction by 534-fold, reducing a representative three-parameter fit from more than 5 h to approximately 1 min. Measurements of Al/SiO2 samples yield consistent silica thermal conductivities using conventional and patterned transducers, validating the surrogate-based fitting framework. For anisotropic Z-cut LiNbO3, the method yields radial and cross-plane thermal conductivities of 3.35 ± 0.19 and 3.80±0.75W/(mK), respectively, in close agreement with independent time-domain thermoreflectance measurements on the same material. Transfer learning extends the surrogate to broader parameter domains using only 1000 new simulations, compared with 6000 used to develop the original model, while outperforming direct training under the same target-domain data budget. This framework enables rapid inverse thermal characterization for complex measurement geometries where repeated high-fidelity forward simulations would otherwise be computationally prohibitive.

  • Experimental assessment of the Wiedemann–Franz law in thin metal films using thermoreflectance and electrical measurements

    by Zhiwei Deng, Jinlong Ma, Puqing Jiang

    Accurate thermal properties of metal thin films are essential for microelectronic thermal modeling and for interpreting thermoreflectance measurements when signals are sensitive to film thermal transport. In practice, film thermal conductivity is commonly inferred from electrical resistivity via the Wiedemann–Franz (WF) law with the Sommerfeld–Lorenz number L0, neglecting phonon contributions and microstructure-dependent scattering. Here, we combine square-pulsed source (SPS) thermoreflectance with van der Pauw measurements to characterize thermal and electrical transport in Al, Ti, and Ta thin films prepared by thermal evaporation, e-beam evaporation, and magnetron sputtering. SPS measurements from 80 to 300 K yield the film thermal conductivity km and volumetric heat capacity Cm, with Cm agreeing with bulk values within ±8%. Compared with WF-based estimates using L0 and a modeled resistivity, ρmodel(T) = ρbulk(T) + ρ0, km deviates by 5%–20% for Al and Ti and up to 40% for sputtered Ta at 300 K. While the smaller deviations are comparable to experimental uncertainty, the large mismatch for Ta demonstrates the limitation of applying the bulk L0 to highly resistive metal films. Apparent Lorenz numbers Lapp=kmρmeas/T from 150 to 300 K further reveal that deposition-induced disorder, grain-boundary scattering, and possible phase-related effects can modify the correlation between heat and charge transport in thin metal films. These results clarify the applicability of the WF law to deposited metal thin films and offer practical guidance for thermal modeling and thermoreflectance analysis.

  • Open Access

    A transfer-learning-enhanced reduced-order surrogate for rapid thermal property extraction in patterned FDTR

    by Bingjia Xiao, Tao Chen, Puqing Jiang

    Patterned-transducer frequency-domain thermoreflectance (FDTR) improves sensitivity to low-thermal-conductivity materials by suppressing lateral heat spreading in the metal transducer, yet the loss of lateral semi-infinite symmetry invalidates analytical models and necessitates expensive finite-element simulations, making iterative fitting computationally prohibitive. This work develops a transfer-learning-enhanced reduced-order surrogate that directly predicts the phase response for rapid inverse fitting. The proposed approach achieves a 534× speedup over COMSOL with sub-degree accuracy (mean RMSE 0.19°), reducing a representative three-parameter fit from over 5 hours to approximately one minute. Experimental validation on Al/SiO2 samples demonstrates consistent extraction of silica thermal conductivities across conventional and patterned configurations, confirming metrological reliability. Transfer learning further extends the surrogate to expanded parameter domains with limited additional high-fidelity data, cutting training data requirements by over 80% while preserving prediction accuracy. The proposed framework provides a practical route for high-throughput thermal characterization in complex geometries where conventional numerical fitting is infeasible.

  • Open Access

    Physics-Derived Natural Coordinates for Fast Uncertainty Propagation in Multilayer Thermoreflectance

    by Dihui Wang, Puqing Jiang, Tao Chen

    Uncertainty quantification in thermoreflectance measurements of multilayer structures is challenging because thermophysical-property extraction involves nonlinear inverse problems with strongly coupled parameters. Covariance-based analytical propagation is efficient but assumes local linearity and approximately Gaussian fitted variables, whereas Monte Carlo (MC) propagation captures non-Gaussian behavior but is computationally expensive and can be unreliable when simultaneously fitting parameters spanning very different orders of magnitude. Here, we address these issues by combining normalized MC sampling, used to obtain reliable benchmark distributions, with physics-based variable transformations for analytical uncertainty propagation. From the multilayer heat-diffusion equation, we identify natural coordinates: the interfacial thermal resistance 1/G, the substrate combinations \sqrt{k_zk_r} and \sqrt{k_zC}, and the thin-film combinations k_r/C, hC, and Ch^2/k_z. Across six representative multilayer systems, these coordinates are approximately Gaussian even when the original physical parameters are skewed. Performing covariance-based propagation in the transformed space and mapping the results back to physical parameters yields asymmetric confidence intervals that closely match normalized MC benchmarks. The approach preserves the non-Gaussian uncertainty structure of the recovered parameters while avoiding repeated nonlinear refitting, providing a fast and physically interpretable methodology for thermoreflectance uncertainty quantification in multilayer systems governed by diffusive heat conduction.

  • Open Access

    Simultaneous in-situ measurement of pressure-dependent bulk and interfacial thermal properties in thermal interface materials

    by Tao Chen, Bingjia Xiao, Xin Qian, Puqing Jiang

    Thermal interface materials (TIMs) critically govern heat transfer between chips and heat spreaders, yet under practical assembly pressures, their thermal conductivity (k), volumetric heat capacity (C), and interfacial thermal resistance (ITR) co-evolve in ways that existing steady-state and transient methods cannot simultaneously resolve. Here, we extend square-pulsed source (SPS) thermoreflectance to a pressure-controlled platform, enabling simultaneous, in-situ extraction of k, C, and ITR in compressed TIM stacks from a single measurement. By spanning modulation frequencies from 1 Hz to 10 MHz, SPS accesses thermal penetration depths that distinguish bulk heat diffusion/storage from interfacial heat transfer. Measurements on a thermally conductive gel, a thermal pad, and a high-vacuum grease during compression-unloading cycles reveal distinct pressure- and history-dependent behaviors. The gel and pad show increasing k and C, decreasing ITR, and pronounced hysteresis, consistent with coupled bulk densification and interfacial evolution, whereas the grease displays pressure-invariant bulk properties but interface-dominated resistance reduction. Validated against poroelastic and contact-mechanics models, these findings establish a framework for state-aware thermal design in advanced electronic packaging.

  • Depth-resolved thermal conductivity of HFCVD diamond films via square-pulsed thermometry

    by Kexin Zhang, Xiaosong Han, Ershuai Yin, Xin Qian, Junjun Wei, Puqing Jiang

    The integration of high-thermal-conductivity diamond films onto silicon carbide (SiC) substrates offers a promising pathway for thermal management in high-power electronic devices. Here, we investigate the depth-dependent thermal conductivity of a ∼5 μm-thick diamond film grown on SiC by hot filament chemical vapor deposition (HFCVD) using square-pulsed source thermometry. Electron backscatter diffraction and transmission electron microscopy reveal pronounced grain coarsening from the nucleation interface to the film surface. By combining frequency-dependent thermal penetration with a depth-resolved thermal transport model, we quantitatively reconstruct the thermal conductivity profile. The thermal conductivity increases sharply from ∼60 W m−1 K−1 near the nucleation region to ∼200 W m−1 K−1 at the surface, directly reflecting the underlying microstructural evolution. These results provide a physically grounded understanding of graded heat transport in HFCVD diamond and offer practical guidance for engineering diamond-based thermal management layers for next-generation power devices.


  • Universal thermometry of solid–liquid interfacial thermal conductance

    by Tao Chen, Puqing Jiang

    Solid–liquid interfacial thermal conductance (ITC) critically influences heat transport in microfluidic, electronic, and energy systems, yet most optical thermometry techniques are limited to specific metal–liquid interfaces. In this work, we introduce a universal broadband square-pulsed thermometry method that enables simultaneous quantification of ITC across a wide range of arbitrary solid–liquid interfaces while also providing accurate measurements of nanoscale liquid-film thickness. To validate the method, we applied it to Al-water interfaces, yielding ITC values in the range of 50–55 MW m−2 K−1, consistent with prior studies. The technique also reveals markedly lower ITCs for glass-water (9.9 MW m−2 K−1) and Si-water (5.7 MW m−2 K−1), and further measurements on Al-silicone oil (∼10 MW m−2 K−1) and poly(methyl methacrylate) (PMMA)-silicone oil (∼0.4 MW m−2 K−1) extend the validation to highly viscous nonpolar liquids and polymer-liquid interfaces. These results highlight the capability of the method to capture thermal transport differences across diverse solid-liquid combinations. Further comparisons with acoustic/diffuse mismatch models and molecular dynamics simulations, together with theoretical analysis, highlight the influence of vibrational mismatch, wettability, and surface condition on interfacial thermal transport. This broadly applicable technique enables rapid, quantitative characterization of solid-liquid interfacial thermal transport, with broad implications for interfacial heat transfer science and technology.


  • Simultaneous, Non-Contact Measurement of Liquid and Interfacial Thermal Properties via a Differential Square-Pulsed Source Method

    by Tao Chen, Puqing Jiang

    Accurate characterization of heat transport across solid-liquid interfaces is essential for thermal management in micro- and nanoscale systems. Yet existing techniques often require prior knowledge of liquid properties, which complicates the simultaneous resolution of interfacial and bulk behaviors, and lose sensitivity once interfacial conductance exceeds 100 MW m-2 K-1. Here we present a differential square-pulsed source (DSPS) method that provides simultaneous, noncontact measurement of liquid thermal conductivity, volumetric heat capacity, and solid-liquid interfacial conductance without any predefined liquid parameters. Dual-frequency excitation combined with in situ substrate referencing enables property extraction from multilayer structures, and numerical simulations show a typical uncertainty of about 8% in interfacial conductance, confirming robustness. The protocol is validated for a wide spectrum of liquids, including oils, lubricants, aqueous electrolytes, and pure water, with excellent agreement with literature values for bulk properties. Analysis of the data set clarifies how vibrational-spectrum mismatch, ionic layering, and related interfacial phenomena govern heat transfer, and demonstrates that oleophilic hexadecyl silane modification of aluminum increases interfacial conductance by a factor of 16. The results reveal that conductance can be strongly tuned through surface wettability and chemical functionalization, offering direct guidelines for interface engineering. Because the approach is readily extendable to soft materials such as thermal-interface gels, it promises broad applicability in emerging interface-dominated thermal technologies.