Kevin Colligan Yates

Current-mode Cherenkov aerogel detectors have been used to measure time resolved spectra of MeV radiographic x-ray sources and have been considered to replace gas Cherenkov systems. The simulations of the Cherenkov response of aerogel detectors have uncertainties in how to model the complex structure of aerogels. Data from three sites—the Idaho electron beam, the Los Alamos Site electron beam and microtron sources at Los Alamos—have been used to calibrate the relative energy response of 15 aerogels, varying in density from 10 to 430 mg/cm3, from incident electrons with energies from 1 to 12 MeV. Detector simulations need to introduce density variation in the aerogels to match the collected data.

This document summarizes the activities at the Mykonos Pulsed Power Facility during the calendar year 2025. Section 1 reports on the yearly shot statistics along with some facility highlights. Section 2 discusses the many improvements we were able to complete this year, thanks to the generous Mykonos Academic Access Programs (MAAP) funding from SSAP and Sandia strategic investments. Section 3 focuses on each individual campaign and their respective results.

Experiments on the 1-MA, 100-ns-rise-time Mykonos Facility demonstrate rotation of electrothermal instability (ETI)-driven overheating structure on 1.00-mm-diameter, 10-nm-surface roughness, 99.999%-pure aluminum rods, which are pulsed with helically polarized surface magnetic field. Rods are machined to include pairs of 10-micron-scale quasi-hemispherical voids or “engineered defects (ED)” which provide the dominant current density perturbation from which ETI grows most rapidly. Experiments include an axial magnetic field component through the addition of a helically wound return-current electrode or “helical return can (HRC).” For a given HRC design, azimuthal field (Bɵ) and axial field (Bz) components rise at a prescribed and fixed ratio, driving an increasing magnetic field of constant polarization at the rod's surface; most experiments generated surface magnetic field at a 15-degree field polarization angle (from horizontal) defined as ɸB = arctan(Bz/Bɵ). ETI-driven emission patterns from individual ED are observed to rotate along ɸB, while emission patterns from dielectric-coated ED pairs are shown to elongate and preferentially merge along ɸB, in qualitative agreement with 3D-magnetohydrodynamic simulations. These data strongly support that for a randomized distribution of current density perturbations on a high-current density conductor, nearby perturbations will favorably merge about ɸB, with the degree of merging increasing with current. Such observations offer fundamental new understanding of the seeding mechanisms of the helical magneto-Rayleigh Taylor (MRT) instabilities observed from axially magnetized magnetically driven imploding liners.

In our paper,1 we would like to make a few additions and corrections. In our paper,1 we would like to make a few additions and corrections.

The Z machine is a current driver producing up to 30 MA in 100 ns that utilizes a wide range of diagnostics to assess accelerator performance and target behavior conduct experiments that use the Z target as a source of radiation or high pressures. We review the existing suite of diagnostic systems, including their locations and primary configurations. The diagnostics are grouped in the following categories: pulsed power diagnostics, x-ray power and energy, x-ray spectroscopy, x-ray imaging (including backlighting, power flow, and velocimetry), and nuclear detectors (including neutron activation). We will also briefly summarize the primary imaging detectors we use at Z: image plates, x-ray and visible film, microchannel plates, and the ultrafast x-ray imager. The Z shot produces a harsh environment that interferes with diagnostic operation and data retrieval. We term these detrimental processes “threats” of which only partial quantifications and precise sources are known. We summarize the threats and describe techniques utilized in many of the systems to reduce noise and backgrounds.

Inhomogeneities in a current-carrying conductor promote non-uniform heating and expansion through the complex feedback between current density, electrical resistivity, Ohmic heating, temperature, and hydrodynamics. Three-dimensional-magnetohydrodynamic (3D-MHD) simulations suggest that μm-scale resistive inclusions or voids seed local overheating and through hydrodynamic explosion generate continuously growing craters which become several times larger than the initial perturbation. The ejected mass is the genesis of an electrothermally driven plasma filament which develops at lower current than plasmas on uniform surfaces adjacent to the defect. This result suggests that 1D or even 2D treatments are largely inadequate for detailed prediction of plasma formation. To test computational predictions, z-pinch experiments driven to 1 MA studied ultra-high-purity aluminum rods which were then machined to include pairs of quasi-hemispherical voids or “engineered defects (ED)” on the current-carrying surface. ED are the dominant current-density perturbation and reproducibly drive local overheating which can be compared with 3D-MHD simulation. Data from high-resolution-gated imagers of visible surface emissions confirm many simulation predictions, including the surface topography of local overheating, and the propensity for neighboring ED to prematurely source plasmas which then connect to form a plasma filament. Results also provide conditional support of theory which suggests heating similarity; that is, heating is independent of ED size for geometrically scaled ED.

Significant variations in plasma formation have been observed for thick aluminum rods with varying initial surface conditions when pulsed by an intense current in a z-pinch configuration. Rods were fabricated on a lathe to a diameter of 1.0 mm followed by a 300 μm wide and 6 mm long strip milled on the surface to remove a portion of the azimuthally extended machining marks left by the lathe. A subset of these rods was then electropolished, reducing the azimuthally extended machining marks and reducing the mean surface roughness. The fabrication process provided two types of rods with several surface finishes: a smooth surface (both the milled flat face and curved region), a rough surface (milled flat faced region), and an azimuthally extended rough surface (curved region), to study the effect of surface finish on plasma formation. Rods with azimuthally extended surface defects left by the machining process form plasma early compared to rods that have had the azimuthally extended features removed and/or reduce by electropolishing the surface or milling away a section of the surface.