Janne Haapanen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Janne Haapanen has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Jyrki M. Mäkelä
Laboratory of Physics, Tampere University of Technology, Tampere, Finland
18 shared publications - Jurkka Kuusipalo
Tampere University of Technology
14 shared publications - Hannu Teisala
Tampere University of Technology
13 shared publications - Martti Toivakka
Laboratory of Natural Materials Technology, Åbo Akademi University, Turku, Finland
12 shared publications Mikko Tuominen
Laboratory of Materials Science, Tampere University of Technology, Tampere, Finland
9 shared publicationsMikko Aromaa
Laboratory of Physics, Tampere University of Technology, Tampere, Finland
8 shared publications
Latest Publications
- 22 November 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (3) , 035004
On the limit of superhydrophobicity: defining the minimum amount of TiO2 nanoparticle coating
Fabrication of superhydrophobic surfaces in large scale has been in high interest for several years, also titanium oxide nanostructures having been applied for the purpose. Optimizing the amount and structure of the TiO2 material in the coating will play a key role when considering upscaling. Here, we take a look at fabricating the superhydrophobic surface in a one-step roll-to-roll pilot scale process by depositing TiO2 nanoparticles from a Liquid Flame Spray onto a moving paperboard substrate. In order to find the minimum amount of nanomaterial still sufficient for creating superhydrophobicity, we varied nanoparticle production rate, flame distance from the substrate and line speed. Since the deposited amount of material sideways from the flame path was seen to decrease gradually, spatial analysis enabled us to consistently determine the minimum amount of TiO2 nanoparticles on the substrate needed to achieve superhydrophobicity. Amount as low as 20-30 mg/m2 of TiO2 nanoparticles was observed to be sufficient. The scanning electron microscopy revealed that at this amount, the surface was covered with nanoparticles only partially, but still sufficiently to create a hierarchical structure to affect wetting significantly. Based on XPS analysis, it became apparent that TiO2 gathers hydrocarbons on the surface to develop the surface chemistry towards hydrophobic, but below the critical amount of TiO2 nanoparticles, the chemistry could not enable superhydrophobicity anymore. While varying the deposited amount of TiO2, besides the local spatial variance of the coating amount, also the overall yield was studied. Within the text matrix, a yield up to 44 % was achieved. In conclusion, superhydrophobicity was achieved at all tested line speeds (50 to 300 m/min), even if the amount of TiO2 varied significantly (20 to 230 mg/m2).
- 22 November 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (3) , 035004
On the limit of superhydrophobicity: defining the minimum amount of TiO2 nanoparticle coating
Fabrication of superhydrophobic surfaces in large scale has been in high interest for several years, also titanium oxide nanostructures having been applied for the purpose. Optimizing the amount and structure of the TiO2 material in the coating will play a key role when considering upscaling. Here, we take a look at fabricating the superhydrophobic surface in a one-step roll-to-roll pilot scale process by depositing TiO2 nanoparticles from a Liquid Flame Spray onto a moving paperboard substrate. In order to find the minimum amount of nanomaterial still sufficient for creating superhydrophobicity, we varied nanoparticle production rate, flame distance from the substrate and line speed. Since the deposited amount of material sideways from the flame path was seen to decrease gradually, spatial analysis enabled us to consistently determine the minimum amount of TiO2 nanoparticles on the substrate needed to achieve superhydrophobicity. Amount as low as 20-30 mg/m2 of TiO2 nanoparticles was observed to be sufficient. The scanning electron microscopy revealed that at this amount, the surface was covered with nanoparticles only partially, but still sufficiently to create a hierarchical structure to affect wetting significantly. Based on XPS analysis, it became apparent that TiO2 gathers hydrocarbons on the surface to develop the surface chemistry towards hydrophobic, but below the critical amount of TiO2 nanoparticles, the chemistry could not enable superhydrophobicity anymore. While varying the deposited amount of TiO2, besides the local spatial variance of the coating amount, also the overall yield was studied. Within the text matrix, a yield up to 44 % was achieved. In conclusion, superhydrophobicity was achieved at all tested line speeds (50 to 300 m/min), even if the amount of TiO2 varied significantly (20 to 230 mg/m2).
- 14 August 2018
- Published by Wiley in Advanced Materials Interfaces
- Vol. 5 (20)
Icephobicity of Slippery Liquid Infused Porous Surfaces under Multiple Freeze–Thaw and Ice Accretion–Detachment Cycles
Surface engineering can be used to prevent ice accumulation and adhesion in environments that deal with icing problems. One recent engineering approach, slippery liquid infused porous surfaces (SLIPS), comprises a smooth and slippery lubricating surface, where lubricant is trapped within the pores of a solid material to repel various substances, such as water and ice. However, it remains unclear whether the slippery surfaces retain their icephobic characteristics under the impact of supercooled water droplets or repeated freezing and melting cycles. Here, the icephobic properties of SLIPS are evaluated under multiple droplet freeze–thaw and ice accretion–detachment cycles and compared to hydrophobic and superhydrophobic surfaces. The experiments are designed to mimic real environmental conditions, thus, the icephobicity is investigated in icing wind tunnel, where ice accretion occurs through the impact of supercooled water droplets. The adhesion of ice remained extremely low, <10 kPa, which is four times lower than ice adhesion onto smooth fluoropolymer surfaces, even after repeated ice accretion–detachment cycles. Moreover, cyclic droplet freeze–thaw experiments provide insight into the effects of temperature cycling on SLIPS wettability, showing stable wetting performance. The results suggest liquid infused porous surfaces as a potential solution to icephobicity under challenging and variating environmental conditions.
- 14 August 2018
- Published by Wiley in Advanced Materials Interfaces
- Vol. 5 (20)
Icephobicity of Slippery Liquid Infused Porous Surfaces under Multiple Freeze–Thaw and Ice Accretion–Detachment Cycles
Surface engineering can be used to prevent ice accumulation and adhesion in environments that deal with icing problems. One recent engineering approach, slippery liquid infused porous surfaces (SLIPS), comprises a smooth and slippery lubricating surface, where lubricant is trapped within the pores of a solid material to repel various substances, such as water and ice. However, it remains unclear whether the slippery surfaces retain their icephobic characteristics under the impact of supercooled water droplets or repeated freezing and melting cycles. Here, the icephobic properties of SLIPS are evaluated under multiple droplet freeze–thaw and ice accretion–detachment cycles and compared to hydrophobic and superhydrophobic surfaces. The experiments are designed to mimic real environmental conditions, thus, the icephobicity is investigated in icing wind tunnel, where ice accretion occurs through the impact of supercooled water droplets. The adhesion of ice remained extremely low, <10 kPa, which is four times lower than ice adhesion onto smooth fluoropolymer surfaces, even after repeated ice accretion–detachment cycles. Moreover, cyclic droplet freeze–thaw experiments provide insight into the effects of temperature cycling on SLIPS wettability, showing stable wetting performance. The results suggest liquid infused porous surfaces as a potential solution to icephobicity under challenging and variating environmental conditions.
- 1 February 2018
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 15 (3) , 623-632
Characteristics of nFOG, an aerosol-based wet thin film coating technique
- 1 February 2018
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 15 (3) , 623-632
Characteristics of nFOG, an aerosol-based wet thin film coating technique
- 1 October 2017
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 103, 268-274
Comparison of different coating techniques on the properties of FucoPol films
- 1 October 2017
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 103, 268-274
Comparison of different coating techniques on the properties of FucoPol films
- Open Access
- 1 January 2017
- Published by Hosokawa Powder Technology Foundation in KONA Powder and Particle Journal
- Vol. 34, 141-154
Liquid Flame Spray—A Hydrogen-Oxygen Flame Based Method for Nanoparticle Synthesis and Functional Nanocoatings
In this review article, a specific flame spray pyrolysis method, Liquid Flame Spray (LFS), is introduced to produce nanoparticles using a coflow type hydrogen-oxygen flame utilizing pneumatically sprayed liquid precursor. This method has been widely used in several applications due to its characteristic features, from producing nanopowders and nanostructured functional coatings to colouring of art glass and generating test aerosols. These special characteristics will be described via the example applications where the LFS has been applied in the past 20 years.
- 1 January 2017
- Published by Hosokawa Powder Technology Foundation in KONA Powder and Particle Journal
- Vol. 34, 141-154
Open AccessLiquid Flame Spray—A Hydrogen-Oxygen Flame Based Method for Nanoparticle Synthesis and Functional Nanocoatings
In this review article, a specific flame spray pyrolysis method, Liquid Flame Spray (LFS), is introduced to produce nanoparticles using a coflow type hydrogen-oxygen flame utilizing pneumatically sprayed liquid precursor. This method has been widely used in several applications due to its characteristic features, from producing nanopowders and nanostructured functional coatings to colouring of art glass and generating test aerosols. These special characteristics will be described via the example applications where the LFS has been applied in the past 20 years.
- 19 June 2015
- Published by Taylor & Francis in Aerosol Science and Technology
- Vol. 49 (9) , 767-776
Coating of Silica and Titania Aerosol Nanoparticles by Silver Vapor Condensation
- 19 June 2015
- Published by Taylor & Francis in Aerosol Science and Technology
- Vol. 49 (9) , 767-776
Coating of Silica and Titania Aerosol Nanoparticles by Silver Vapor Condensation
- 28 May 2015
- Published by Springer Nature in MRS Proceedings
- Vol. 1747
Roll-to-Roll Coating by Liquid Flame Spray Nanoparticle Deposition
- 28 May 2015
- Published by Springer Nature in MRS Proceedings
- Vol. 1747
Roll-to-Roll Coating by Liquid Flame Spray Nanoparticle Deposition
- 1 January 2015
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 149-150, 230-237
Binary TiO2/SiO2 nanoparticle coating for controlling the wetting properties of paperboard
- 1 January 2015
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 149-150, 230-237
Binary TiO2/SiO2 nanoparticle coating for controlling the wetting properties of paperboard
- 1 December 2014
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 29 (4) , 747-759
Review on Liquid Flame Spray in paper converting: Multifunctional superhydrophobic nanoparticle coatings
Article Review on Liquid Flame Spray in paper converting: Multifunctional superhydrophobic nanoparticle coatings was published on December 1, 2014 in the journal Nordic Pulp & Paper Research Journal (volume 29, issue 4).
- 1 December 2014
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 29 (4) , 747-759
Review on Liquid Flame Spray in paper converting: Multifunctional superhydrophobic nanoparticle coatings
Article Review on Liquid Flame Spray in paper converting: Multifunctional superhydrophobic nanoparticle coatings was published on December 1, 2014 in the journal Nordic Pulp & Paper Research Journal (volume 29, issue 4).
- 22 October 2014
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 6 (22) , 20060-20066
Paper-Based Microfluidics: Fabrication Technique and Dynamics of Capillary-Driven Surface Flow
Paper-based devices provide an alternative technology for simple, low-cost, portable, and disposable diagnostic tools for many applications, including clinical diagnosis, food quality control, and environmental monitoring. In this study we report a two-step fabrication process for creating two-dimensional microfluidic channels to move liquids on a hydrophobized paper surface. A highly hydrophobic surface was created on paper by TiO2 nanoparticle coating using a high-speed, roll-to-roll liquid flame spray technique. The hydrophilic pattern was then generated by UV irradiation through a photomask utilizing the photocatalytic property of TiO2. The flow dynamics of five model liquids with differing surface tensions 48–72 mN·m–1 and viscosities 1–15 mN·m–2 was studied. The results show that the liquid front (l) in a channel advances in time (t) according to the power law l = Zt0.5 (Z is an empirical constant which depend on the liquid properties and channel dimensions). The flow dynamics of the liquids with low viscosity show a dependence on the channel width and the droplet volume, while the flow of liquids with high viscosity is mainly controlled by the viscous forces.
- 22 October 2014
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 6 (22) , 20060-20066
Paper-Based Microfluidics: Fabrication Technique and Dynamics of Capillary-Driven Surface Flow
Paper-based devices provide an alternative technology for simple, low-cost, portable, and disposable diagnostic tools for many applications, including clinical diagnosis, food quality control, and environmental monitoring. In this study we report a two-step fabrication process for creating two-dimensional microfluidic channels to move liquids on a hydrophobized paper surface. A highly hydrophobic surface was created on paper by TiO2 nanoparticle coating using a high-speed, roll-to-roll liquid flame spray technique. The hydrophilic pattern was then generated by UV irradiation through a photomask utilizing the photocatalytic property of TiO2. The flow dynamics of five model liquids with differing surface tensions 48–72 mN·m–1 and viscosities 1–15 mN·m–2 was studied. The results show that the liquid front (l) in a channel advances in time (t) according to the power law l = Zt0.5 (Z is an empirical constant which depend on the liquid properties and channel dimensions). The flow dynamics of the liquids with low viscosity show a dependence on the channel width and the droplet volume, while the flow of liquids with high viscosity is mainly controlled by the viscous forces.