Sixing Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sixing Liu has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
Hong Miao
Yangzhou Univ, Sch Mech Engn, Yangzhou, Jiangsu, Peoples R China
4 shared publications- Shanwen Zhang
School of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
3 shared publications Tianhong Liu
Yangzhou Univ, Sch Informat Engn, Yangzhou, Jiangsu, Peoples R China
3 shared publicationsBing Xiao
2 shared publicationsHaozhong Xiao
2 shared publications- Hong Miao
College of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
2 shared publications
Latest Publications
- 1 January 2024
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 40 (3) , 285-291
Identification Localization and Gathering of Pepper Based on Depth Camera and Inverse Kinematics
Highlights The spatial coordinate position of peppers is obtained by YOLOv5 algorithm fused with localization technique. The inverse kinematics for gathering arm is solved by disassembly and Euler-angle method. Pentadic polynomials are applied to realize the motion planning and control of robotic arm. The proposed method achieves an average gathering success rate about 60%. Abstract. To avoid mutation and interference with intelligent gathering, an autonomous gathering method is proposed in this paper. An improved YOLOv5 target detection algorithm is used to recognize peppers. The kinematics solution of the robotic arm is realized by using the disassembly method and the Euler-angle method. Simulating and modeling robotic arms is conducted by the Robotic Toolbox in Matlab. The robotic arm's spatial motion planning is controlled by the pentadic polynomial interpolation method. The feasibility of the inverse solution and planning is verified in Matlab. Different conditions’ gathering experiments are conducted on the gathering platform. Experiments show that this method is smooth and interference-free, with a high gathering success rate, realizing the accurate gathering of single, small fruits in complex environments. Keywords: Robot gathering, Robotic arm inverse kinematics, Target detection, Trajectory planning
- 1 January 2024
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 40 (3) , 285-291
Identification Localization and Gathering of Pepper Based on Depth Camera and Inverse Kinematics
Highlights The spatial coordinate position of peppers is obtained by YOLOv5 algorithm fused with localization technique. The inverse kinematics for gathering arm is solved by disassembly and Euler-angle method. Pentadic polynomials are applied to realize the motion planning and control of robotic arm. The proposed method achieves an average gathering success rate about 60%. Abstract. To avoid mutation and interference with intelligent gathering, an autonomous gathering method is proposed in this paper. An improved YOLOv5 target detection algorithm is used to recognize peppers. The kinematics solution of the robotic arm is realized by using the disassembly method and the Euler-angle method. Simulating and modeling robotic arms is conducted by the Robotic Toolbox in Matlab. The robotic arm's spatial motion planning is controlled by the pentadic polynomial interpolation method. The feasibility of the inverse solution and planning is verified in Matlab. Different conditions’ gathering experiments are conducted on the gathering platform. Experiments show that this method is smooth and interference-free, with a high gathering success rate, realizing the accurate gathering of single, small fruits in complex environments. Keywords: Robot gathering, Robotic arm inverse kinematics, Target detection, Trajectory planning
- 1 January 2022
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 38 (3) , 599-608
Simultaneous Application of Vacuum and Infrared Drying to Whole Drying Process of Bitter Gourd Slices: Design, Drying Kinetics, Experiment, Characteristic, Energy Aspect
- 1 January 2022
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 38 (3) , 599-608
Simultaneous Application of Vacuum and Infrared Drying to Whole Drying Process of Bitter Gourd Slices: Design, Drying Kinetics, Experiment, Characteristic, Energy Aspect
- Open Access
- 13 April 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (8) , 3118
Laser Sealing for Vacuum Plate Glass with PbO-TiO2-SiO2-RxOy Solder
Laser sealing for vacuum plate glass is a key step in developing the cost-effective smart vacuum-glass window for the drive towards net-zero energy buildings. In this paper, the pores, cracks, and interface with laser welding are analyzed in depth using PbO-TiO2-SiO2-RxOy system sealing solder to prepare vacuum flat glass. The microstructure of the sealing layer was analyzed by a BX41M-LED metallographic microscope, and the interfacial bonding characteristics were observed by thermal field emission scanning electron microscopy (SEM). The solder was analyzed by an energy spectrometer, and the influence of laser power, sealing temperature, and sealing speed on the gas holes and the crack sand interface separation of the sealing layer are reported. The results show that when the laser power reached 80 W at the welding speed of 2 mm/s, the bulk solder disappeared to most of the quantity and the sealing surface density was higher, due to which negligible pores and micro cracks were found. Thus, the sealing quality of the sealing layer is considered to be suitable when the temperature of 470 °C was maintained and the solder has 68.93% of Pb and 3.04% Si in the atom fraction to achieve the wet the glass substrate surface whilst improving the bonding quality.
- 13 April 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (8) , 3118
Open AccessLaser Sealing for Vacuum Plate Glass with PbO-TiO2-SiO2-RxOy Solder
Laser sealing for vacuum plate glass is a key step in developing the cost-effective smart vacuum-glass window for the drive towards net-zero energy buildings. In this paper, the pores, cracks, and interface with laser welding are analyzed in depth using PbO-TiO2-SiO2-RxOy system sealing solder to prepare vacuum flat glass. The microstructure of the sealing layer was analyzed by a BX41M-LED metallographic microscope, and the interfacial bonding characteristics were observed by thermal field emission scanning electron microscopy (SEM). The solder was analyzed by an energy spectrometer, and the influence of laser power, sealing temperature, and sealing speed on the gas holes and the crack sand interface separation of the sealing layer are reported. The results show that when the laser power reached 80 W at the welding speed of 2 mm/s, the bulk solder disappeared to most of the quantity and the sealing surface density was higher, due to which negligible pores and micro cracks were found. Thus, the sealing quality of the sealing layer is considered to be suitable when the temperature of 470 °C was maintained and the solder has 68.93% of Pb and 3.04% Si in the atom fraction to achieve the wet the glass substrate surface whilst improving the bonding quality.
- Open Access
- 12 April 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (8) , 3083
Thermal Analysis of a New Neutron Shielding Vacuum Multiple Glass
The neutron shielding glass is widely used in nuclear/fusion plants. To improve its temperature resistance and heat insulation, a Gadolinium (Gd)-containing laminate vacuum multiple glass is proposed by using the vacuum insulation method. A 3D finite element model validated by theoretical calculation was developed to analyse the heat transfer path and numerical simulation of the multiple glass was carried out to obtain the temperature distribution and the maximum temperatures of the organic glass in relation to dynamic working temperatures, the sealing agent width, view size, and vacuum thermal conductivity. The results show that the vacuum layer between common glasses can make the work temperature of neutron shielding glass increase. The multiple glass has good heat-shielding performance and it is expected to work in a high-temperature environment. In addition, the vacuum layer between the common glasses and the sealing agent width decay with respect to the view size and vacuum thermal conductivity show an increase in the working temperature of the neutron shielding glass. It was concluded that the order of affecting the temperatures of the organic glass follows the pattern of: view size > vacuum thermal conductivity > sealing agent width.
- 12 April 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (8) , 3083
Open AccessThermal Analysis of a New Neutron Shielding Vacuum Multiple Glass
The neutron shielding glass is widely used in nuclear/fusion plants. To improve its temperature resistance and heat insulation, a Gadolinium (Gd)-containing laminate vacuum multiple glass is proposed by using the vacuum insulation method. A 3D finite element model validated by theoretical calculation was developed to analyse the heat transfer path and numerical simulation of the multiple glass was carried out to obtain the temperature distribution and the maximum temperatures of the organic glass in relation to dynamic working temperatures, the sealing agent width, view size, and vacuum thermal conductivity. The results show that the vacuum layer between common glasses can make the work temperature of neutron shielding glass increase. The multiple glass has good heat-shielding performance and it is expected to work in a high-temperature environment. In addition, the vacuum layer between the common glasses and the sealing agent width decay with respect to the view size and vacuum thermal conductivity show an increase in the working temperature of the neutron shielding glass. It was concluded that the order of affecting the temperatures of the organic glass follows the pattern of: view size > vacuum thermal conductivity > sealing agent width.
- Open Access
- 31 October 2019
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2019, 1-5
The Effect of Welding Speed on the Micromorphology and Mechanical Properties of Laser-Sealed Vacuum Flat Glazing Joints
To explore the effect of welding speed on the micromorphology and mechanical properties of the laser-welded vacuum plate glazing joints, this paper introduced the research status of the laser welding vacuum glazing and then carried out the preparation for experimental materials. This paper also analyzed the microstructure, the cause of the pores, and the mechanical properties of the sealing layer. The results show that the smaller the welding speed is, the more fully the solder melts. When the welding speed is 80 mm/min, the sealing layer generates the large thermal stress due to excessive laser input energy, which results in many connected cracks in the sealing layer. The porosity of the sealing layer increases with the increase of the welding speed. The thickness of the interface reaction wetting layer decreases with the increase of the welding speed. The hardness, tensile strength, and shear strength of the sealing layer will increase first and then decrease with the increase of welding speed. These studies can provide the theoretical basis for laser sealing manufacturing of vacuum plate glazing.
- 31 October 2019
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2019, 1-5
Open AccessThe Effect of Welding Speed on the Micromorphology and Mechanical Properties of Laser-Sealed Vacuum Flat Glazing Joints
To explore the effect of welding speed on the micromorphology and mechanical properties of the laser-welded vacuum plate glazing joints, this paper introduced the research status of the laser welding vacuum glazing and then carried out the preparation for experimental materials. This paper also analyzed the microstructure, the cause of the pores, and the mechanical properties of the sealing layer. The results show that the smaller the welding speed is, the more fully the solder melts. When the welding speed is 80 mm/min, the sealing layer generates the large thermal stress due to excessive laser input energy, which results in many connected cracks in the sealing layer. The porosity of the sealing layer increases with the increase of the welding speed. The thickness of the interface reaction wetting layer decreases with the increase of the welding speed. The hardness, tensile strength, and shear strength of the sealing layer will increase first and then decrease with the increase of welding speed. These studies can provide the theoretical basis for laser sealing manufacturing of vacuum plate glazing.
- 1 May 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 101, 189-194
Microstructure characteristics of vacuum glazing brazing joints using laser sealing technique
- 1 May 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 101, 189-194
Microstructure characteristics of vacuum glazing brazing joints using laser sealing technique
- 1 January 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 286, 376-382
Characteristics of Al2O3/diamond/c-BN/SiC grain steel brazing joints using Cu–Sn–Ti active filler powder alloys
- 1 January 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 286, 376-382
Characteristics of Al2O3/diamond/c-BN/SiC grain steel brazing joints using Cu–Sn–Ti active filler powder alloys