Gesa Patzelt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gesa Patzelt has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Deissenberger
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM Wiener Straße 12 D‐28359 Bremen Germany
1 shared publication - Andreas Hartwig
Fraunhofer Institute for Manufacturing Technology and Advanced Materials (IFAM) Bremen Germany
1 shared publication Andrej Stake
Fraunhofer Institute for Manufacturing Technology and Advanced Material Research (IFAM), Bremen, Germany
1 shared publication- Bernd Mayer
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, 28359 Bremen, Germany
1 shared publication - Joshua Lommes
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM Wiener Straße 12 D‐28359 Bremen Germany
1 shared publication Judith Geils
Fraunhofer Institute for Manufacturing Technology and Advanced Material Research (IFAM), Bremen, Germany
1 shared publication
Latest Publications
- Open Access
- 12 January 2024
- Published by Wiley in Advanced Materials Interfaces
- Vol. 11 (10)
Freeze Drying of Organically Modified Layered Silicates as Key Step to Improve the Barrier Properties of Organic Coatings for High Power Electronics Protection
Organically modified layered silicates can be used as barrier pigments in organic coating systems to reduce the permeation of water vapor and gases, e.g., oxygen as well as harmful gases that promote corrosion. Unmodified layered silicates are not sufficient to reduce the permeation significantly. However, the arrangement and orientation of the particles have an enormous impact on the later performance in the barrier film. In organic solvents or non‐aqueous polymer matrices the non‐modified layered silicates cannot exfoliate adequately. The organic modification influences the layer spacing and the compatibility to organic solvents. Layered silicates are modified with dodecylamine to enhance the spacing layer. The spacing layer is enhanced by 55% caused by the organic modification as it is commonly known. In contrast to previous work freeze drying of the organically modified layered silicates improved the particle distribution and by this barrier properties significantly. The modified particles reduce the diffusion of water and oxygen by ≈99.6% and 97.2%, respectively. The corrosive gas test of electronic circuit boards shows no growth of dendrites and no failure of the electronics in contrast to protective coating without the layered silicates.
- 12 January 2024
- Published by Wiley in Advanced Materials Interfaces
- Vol. 11 (10)
Open AccessFreeze Drying of Organically Modified Layered Silicates as Key Step to Improve the Barrier Properties of Organic Coatings for High Power Electronics Protection
Organically modified layered silicates can be used as barrier pigments in organic coating systems to reduce the permeation of water vapor and gases, e.g., oxygen as well as harmful gases that promote corrosion. Unmodified layered silicates are not sufficient to reduce the permeation significantly. However, the arrangement and orientation of the particles have an enormous impact on the later performance in the barrier film. In organic solvents or non‐aqueous polymer matrices the non‐modified layered silicates cannot exfoliate adequately. The organic modification influences the layer spacing and the compatibility to organic solvents. Layered silicates are modified with dodecylamine to enhance the spacing layer. The spacing layer is enhanced by 55% caused by the organic modification as it is commonly known. In contrast to previous work freeze drying of the organically modified layered silicates improved the particle distribution and by this barrier properties significantly. The modified particles reduce the diffusion of water and oxygen by ≈99.6% and 97.2%, respectively. The corrosive gas test of electronic circuit boards shows no growth of dendrites and no failure of the electronics in contrast to protective coating without the layered silicates.
- 23 March 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (27)
Aging of anhydride‐hardened epoxies in lubricants at elevated temperatures
In automotive under‐the‐hood applications, electronics respectively their packaging materials come in contact with automotive fluids. The effect of automatic transmission fluid (ATF) on an anhydride‐cured epoxy was investigated at temperatures up to 180 °C for up to 1000 h. This study has shown that ATF retards the oxidative aging of the epoxy, presumably due to oxygen consumption. Whereas in air the material underwent a thermo‐oxidative aging with a mass loss of up to 4% and a strong broadening of Tg to higher temperatures, in ATF a temperature dependent distinctive drop of Tg from 142 to 126 °C after 1000 h aging at 180 °C, and a mass loss of maximum 1% was observed which might be a thermal decomposition of the epoxy material. A slight broadening of the damping factors might indicate an intrusion of ATF components. A color change of the samples could be observed after aging in air and ATF, with the discoloration in air being more intense. An explanation for the color change might be either a minor amount of oxygen causing an oxidative discoloration reaction or the intrusion of colored ATF degradation products. While the oxidation‐kinetics in air exhibited Arrhenius temperature‐dependence the mechanism in ATF changed above 165 °C. An acceleration of aging tests at temperatures beyond 150 °C is, therefore, not possible. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44877.
- 23 March 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (27)
Aging of anhydride‐hardened epoxies in lubricants at elevated temperatures
In automotive under‐the‐hood applications, electronics respectively their packaging materials come in contact with automotive fluids. The effect of automatic transmission fluid (ATF) on an anhydride‐cured epoxy was investigated at temperatures up to 180 °C for up to 1000 h. This study has shown that ATF retards the oxidative aging of the epoxy, presumably due to oxygen consumption. Whereas in air the material underwent a thermo‐oxidative aging with a mass loss of up to 4% and a strong broadening of Tg to higher temperatures, in ATF a temperature dependent distinctive drop of Tg from 142 to 126 °C after 1000 h aging at 180 °C, and a mass loss of maximum 1% was observed which might be a thermal decomposition of the epoxy material. A slight broadening of the damping factors might indicate an intrusion of ATF components. A color change of the samples could be observed after aging in air and ATF, with the discoloration in air being more intense. An explanation for the color change might be either a minor amount of oxygen causing an oxidative discoloration reaction or the intrusion of colored ATF degradation products. While the oxidation‐kinetics in air exhibited Arrhenius temperature‐dependence the mechanism in ATF changed above 165 °C. An acceleration of aging tests at temperatures beyond 150 °C is, therefore, not possible. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44877.
- 21 March 2016
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 13 (4) , 589-596
Anti-icing and anticontamination properties of coatings induced by surface structure
- 21 March 2016
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 13 (4) , 589-596
Anti-icing and anticontamination properties of coatings induced by surface structure