Maikel Fernando Menke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maikel Fernando Menke has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Alysson Raniere Seidel
Industrial Technical School of Santa Maria
21 shared publications - Fabio Ecke Bisogno
Hochschule Koblenz image/svg+xml
11 shared publications M. F. da Silva
Federal University of Santa Maria - UFSM, Electrical and Computational Systems Research and Development Group - GSEC, Group of Intelligence in Lighting - GEDRE, Santa Maria, RS, Brazil
9 shared publications- Jose Marcos Alonso
Department of Electrical Engineering, University of Oviedo, Asturias, Spain
8 shared publications - Marina S. Perdigao
Polytechnic Institute of Coimbra
6 shared publications - Javier Ribas
Department of Electrical Engineering, University of Oviedo, 33003 Oviedo, Spain
3 shared publications
Latest Publications
- Open Access
- 13 March 2025
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 30, e202526
Proposal of Fully Integrated LED Driver with Enhanced Power Density for Street-lighting Applications
This paper proposes a new fully integrated Boost and Buck converter. The topology results from integrating the Boost as the power factor correction (PFC) stage and the Buck as power control (PC) stage. Besides this, the paper presents a methodology for designing the PFC stage inductor based on the inductance ratio between the PFC and PC stage inductances. In this work, the methodology analysis is carried out to enhance the converter power density using magnetics integration. Magnetic circuits and finite elements simulations compare the standalone and the integrated magnetics designs. Finally, the methodology is validated for the proposed fully integrated topology by implementing an 180~W LED driver prototype, which works properly for the grid voltage range (180-250~$V_{rms}$) and ensures full DCM operation between 10 and 100\% of the LED load power. The experimental results show that the proposed topology fulfills the recommendation IEEE 1789-2015 and the standard IEC 61000-3-2 (Class C) in the grid range. The peak efficiency is 93.5\% at 180~$V_{rms}$. The integrated magnetic enables a volume reduction of 20\% compared to the standalone magnetics. The converter component count is significantly reduced compared to LED drivers found in the literature for street-lighting applications.
- 13 March 2025
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 30, e202526
Open AccessProposal of Fully Integrated LED Driver with Enhanced Power Density for Street-lighting Applications
This paper proposes a new fully integrated Boost and Buck converter. The topology results from integrating the Boost as the power factor correction (PFC) stage and the Buck as power control (PC) stage. Besides this, the paper presents a methodology for designing the PFC stage inductor based on the inductance ratio between the PFC and PC stage inductances. In this work, the methodology analysis is carried out to enhance the converter power density using magnetics integration. Magnetic circuits and finite elements simulations compare the standalone and the integrated magnetics designs. Finally, the methodology is validated for the proposed fully integrated topology by implementing an 180~W LED driver prototype, which works properly for the grid voltage range (180-250~$V_{rms}$) and ensures full DCM operation between 10 and 100\% of the LED load power. The experimental results show that the proposed topology fulfills the recommendation IEEE 1789-2015 and the standard IEC 61000-3-2 (Class C) in the grid range. The peak efficiency is 93.5\% at 180~$V_{rms}$. The integrated magnetic enables a volume reduction of 20\% compared to the standalone magnetics. The converter component count is significantly reduced compared to LED drivers found in the literature for street-lighting applications.
- 21 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3029-3038
Energy-Aware Design of a GaN-Based Dual-Purpose Converter for Standalone Lighting Systems
Energy efficiency plays a crucial role in the development of solar-powered standalone lighting systems, as it directly impacts both the system's autonomy and size, ultimately affecting the cost. In scenarios where a single converter simultaneously functions as both battery charger and LED driver, minimizing energy losses becomes challenging due to the different power levels processed in each mode. The use of gallium nitride (GaN) semiconductors in the converter helps achieving this goal as they allow for a wide range of switching frequencies, maintaining high efficiency even in light-load conditions. However, focusing solely on the converter's efficiency in each task may not necessarily minimize energy losses when considering its 24/7 operating characteristic and charger/driver time ratio. This study introduces a methodology tailored to select circuit components and switching frequencies within a GaN-based dual-purpose converter solution. The primary objective is to maximize system autonomy. A comprehensive analytical model of the converter's losses is paired with a search-based algorithm, enabling the evaluation of commercial components. This evaluation pinpoints the combination that minimizes energy consumption, ultimately leading to a more compact design that efficiently harnesses available resources. Experimental results are showcased for a system with a 30W driver and 150W charger, affirming the efficacy of the proposed design methodology. By meticulously selecting parameters, a high-efficiency converter can be realized. This achievement extends the system's autonomy by nearly an hour without necessitating changes to the battery pack's dimensions.
- 21 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3029-3038
Energy-Aware Design of a GaN-Based Dual-Purpose Converter for Standalone Lighting Systems
Energy efficiency plays a crucial role in the development of solar-powered standalone lighting systems, as it directly impacts both the system's autonomy and size, ultimately affecting the cost. In scenarios where a single converter simultaneously functions as both battery charger and LED driver, minimizing energy losses becomes challenging due to the different power levels processed in each mode. The use of gallium nitride (GaN) semiconductors in the converter helps achieving this goal as they allow for a wide range of switching frequencies, maintaining high efficiency even in light-load conditions. However, focusing solely on the converter's efficiency in each task may not necessarily minimize energy losses when considering its 24/7 operating characteristic and charger/driver time ratio. This study introduces a methodology tailored to select circuit components and switching frequencies within a GaN-based dual-purpose converter solution. The primary objective is to maximize system autonomy. A comprehensive analytical model of the converter's losses is paired with a search-based algorithm, enabling the evaluation of commercial components. This evaluation pinpoints the combination that minimizes energy consumption, ultimately leading to a more compact design that efficiently harnesses available resources. Experimental results are showcased for a system with a 30W driver and 150W charger, affirming the efficacy of the proposed design methodology. By meticulously selecting parameters, a high-efficiency converter can be realized. This achievement extends the system's autonomy by nearly an hour without necessitating changes to the battery pack's dimensions.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (3) , 3170-3181
A Control Actuation Concept for Self-Oscillating Resonant Converters
This article presents a concept of controller actuation mechanism for self-oscillating resonant converters (SORCs). Simplicity, robustness, and cost-effectiveness are among the main features of this type of converter. Described as a self-oscillating system with an intrinsic positive-type feedback switching network, also known as the self-oscillating command circuit (SOCC), it performs its own gate drive with self-sustained frequency, designed around an equilibrium point. Designers often disregard this converter as an explicit solution for closed-loop applications, especially those that require extra layers of control, due to its inherent inability to operate under pulse frequency modulation without extra circuitry. Thus, in this article, a robust, efficient, and simple way of controlling the SORC through frequency modulation is proposed. The idea consists of varying the self-oscillating frequency through the equivalent magnetizing inductance of the SOCC, using a mechanism called variable current transformer. Thus, through the injection of a small controllable dc current, it is possible to modulate the frequency of resonant converters. This allows the self-oscillating system to follow a reference current signal, operating in closed-loop over a wide range of input voltage and load variation.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (3) , 3170-3181
A Control Actuation Concept for Self-Oscillating Resonant Converters
This article presents a concept of controller actuation mechanism for self-oscillating resonant converters (SORCs). Simplicity, robustness, and cost-effectiveness are among the main features of this type of converter. Described as a self-oscillating system with an intrinsic positive-type feedback switching network, also known as the self-oscillating command circuit (SOCC), it performs its own gate drive with self-sustained frequency, designed around an equilibrium point. Designers often disregard this converter as an explicit solution for closed-loop applications, especially those that require extra layers of control, due to its inherent inability to operate under pulse frequency modulation without extra circuitry. Thus, in this article, a robust, efficient, and simple way of controlling the SORC through frequency modulation is proposed. The idea consists of varying the self-oscillating frequency through the equivalent magnetizing inductance of the SOCC, using a mechanism called variable current transformer. Thus, through the injection of a small controllable dc current, it is possible to modulate the frequency of resonant converters. This allows the self-oscillating system to follow a reference current signal, operating in closed-loop over a wide range of input voltage and load variation.
- 20 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (12) , 12686-12701
Analysis and Design of the LLC LED Driver Based on State-Space Representation Direct Time-Domain Solution
The LLC resonant converter has been widely used in switched power supply covering several kinds of applications. Although it has been the focus of numerous analysis, their general time-domain (TD) solution is not completely enclosed due to its complexity given by the multiple resonance nature and its variable structure behavior. Consequently, the LLC converter design is also impaired by the lack of an enclosed TD solution. To overcome these issues, this article systematically presents a highly accurate TD solution of the LLC converter supplying a light-emitting diode (LED) load, which is obtained from the state-space representation direct TD solution. Dissimilar to preceding analyses, all the converter states are considered and no current and voltage sinusoidal or average value approximations are taken. Finally, supported by the TD analysis, a new LLC LED driver design procedure is introduced, which is oriented by weighted-average-efficiency concept and constraints that ensure zero voltage switching, enough power gain, and practical switching frequency range over a wide operating window. Experimental results show the feasibility of the proposed design procedure as well as the accurate TD behavior prediction of the LLC converter supplying an LED load. This article is accompanied by active content that exemplifies the proposed TD solution and design procedure.
- 20 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (12) , 12686-12701
Analysis and Design of the LLC LED Driver Based on State-Space Representation Direct Time-Domain Solution
The LLC resonant converter has been widely used in switched power supply covering several kinds of applications. Although it has been the focus of numerous analysis, their general time-domain (TD) solution is not completely enclosed due to its complexity given by the multiple resonance nature and its variable structure behavior. Consequently, the LLC converter design is also impaired by the lack of an enclosed TD solution. To overcome these issues, this article systematically presents a highly accurate TD solution of the LLC converter supplying a light-emitting diode (LED) load, which is obtained from the state-space representation direct TD solution. Dissimilar to preceding analyses, all the converter states are considered and no current and voltage sinusoidal or average value approximations are taken. Finally, supported by the TD analysis, a new LLC LED driver design procedure is introduced, which is oriented by weighted-average-efficiency concept and constraints that ensure zero voltage switching, enough power gain, and practical switching frequency range over a wide operating window. Experimental results show the feasibility of the proposed design procedure as well as the accurate TD behavior prediction of the LLC converter supplying an LED load. This article is accompanied by active content that exemplifies the proposed TD solution and design procedure.
- 24 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 66 (1) , 387-396
LLC LED Driver Small-Signal Modeling and Digital Control Design for Active Ripple Compensation
This paper presents a new approach for the small-signal modeling of the dc–dc LLC resonant converter aimed to supply high-power light-emitting diodes (LEDs). This small-signal modeling procedure is based on the extended describing function method, where for a reliable small-signal model of the LLC LED driver, the equivalent piece-wise linear circuit of the LED has to be considered under some conditions throughout the model development. Otherwise, the obtained model does not reflect the real dynamic behavior of the converter. Furthermore, a numerical analysis is presented showing the conditions where the proposed model better describes the real dynamic behavior of the converter in relation to the traditional approach where the LED is modeled by an equivalent resistance. From the obtained model, the feedback compensator is designed and implemented in order to track the average current reference and avoid output current ripple, consequently sidestepping output light modulation (flicker). Experimental results show the feasibility of the proposed small-signal model and the active ripple compensation through a dimmable digitally controlled LLC LED driver under closed-loop operation.
- 24 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 66 (1) , 387-396
LLC LED Driver Small-Signal Modeling and Digital Control Design for Active Ripple Compensation
This paper presents a new approach for the small-signal modeling of the dc–dc LLC resonant converter aimed to supply high-power light-emitting diodes (LEDs). This small-signal modeling procedure is based on the extended describing function method, where for a reliable small-signal model of the LLC LED driver, the equivalent piece-wise linear circuit of the LED has to be considered under some conditions throughout the model development. Otherwise, the obtained model does not reflect the real dynamic behavior of the converter. Furthermore, a numerical analysis is presented showing the conditions where the proposed model better describes the real dynamic behavior of the converter in relation to the traditional approach where the LED is modeled by an equivalent resistance. From the obtained model, the feedback compensator is designed and implemented in order to track the average current reference and avoid output current ripple, consequently sidestepping output light modulation (flicker). Experimental results show the feasibility of the proposed small-signal model and the active ripple compensation through a dimmable digitally controlled LLC LED driver under closed-loop operation.
- 16 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 6 (3) , 1154-1165
Design Approach for a Self-Oscillating Resonant Converter Operating in High Frequency for LED Applications
In this paper, a design approach for the self-oscillating command circuit as a driver for a resonant converter operating in high frequency for LED applications is proposed. This proposal, conceived from the proposed methodologies, contemplates the influence of the Cascode Gallium Nitride (GaN) FET input and output capacitances, making it relevant to higher switching frequencies, where such parasitic elements lead to increased errors. In conjunction with higher efficiency levels, series resonant inverters like the Zero Voltage Switching (ZVS) half-bridge are known to have potentially reduced size on its reactive components when operated at higher frequencies, resulting in smaller and lighter systems. Combined to the simplicity and low cost of the self-oscillating command circuit, these advantages translate into a simple and cost-effective high-power density application. The self-oscillating resonant converter accurate design is based upon the Describing Function Method as a linearization tool and the extended Nyquist Stability Criterion that evaluates whether or not the system can oscillate around given predicted frequency. Practical input capacitance measurement data for different Silicon MOSFETs and a Cascode GaN FET are compared and considered in order to obtain a high-frequency design approach for a Self-Oscillating Resonant Converter. Simulation and experimental results for a Self-Oscillating Resonant Converter with Cascode GaN FET operating at 1 MHz for a 10 W LED are shown based on the design procedure described.
- 16 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 6 (3) , 1154-1165
Design Approach for a Self-Oscillating Resonant Converter Operating in High Frequency for LED Applications
In this paper, a design approach for the self-oscillating command circuit as a driver for a resonant converter operating in high frequency for LED applications is proposed. This proposal, conceived from the proposed methodologies, contemplates the influence of the Cascode Gallium Nitride (GaN) FET input and output capacitances, making it relevant to higher switching frequencies, where such parasitic elements lead to increased errors. In conjunction with higher efficiency levels, series resonant inverters like the Zero Voltage Switching (ZVS) half-bridge are known to have potentially reduced size on its reactive components when operated at higher frequencies, resulting in smaller and lighter systems. Combined to the simplicity and low cost of the self-oscillating command circuit, these advantages translate into a simple and cost-effective high-power density application. The self-oscillating resonant converter accurate design is based upon the Describing Function Method as a linearization tool and the extended Nyquist Stability Criterion that evaluates whether or not the system can oscillate around given predicted frequency. Practical input capacitance measurement data for different Silicon MOSFETs and a Cascode GaN FET are compared and considered in order to obtain a high-frequency design approach for a Self-Oscillating Resonant Converter. Simulation and experimental results for a Self-Oscillating Resonant Converter with Cascode GaN FET operating at 1 MHz for a 10 W LED are shown based on the design procedure described.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Two-stage digitally controlled led driver based on buck-boost and DC/DC LLC resonant converter
In this study a digitally controlled Light Emitting Diode (LED) driver operating with high power factor, dimming capability and reduced DC-link capacitance is proposed. The proposed LED driver circuit topology, designed to supply a 100 W LED module, is composed by two independent stages. The Power Factor Correction stage is implemented with the buck-boost DC/DC converter, operating in Discontinuous Conduction Mode. This stage provide a high power factor and maintain the average bus voltage controlled in 400 V. Besides, a reduce DC-link capacitance with 25 μF is used, thus allowing the use of log lifetime film capacitors. The second stage comprises the DC/DC Half-Bridge LLC resonant converter, which is in charge to keep controlled the averaged LED current as function of the required dimming level. To avoid output luminous intensity modulation, the control loop of the second stage is designed in order to reduce the LED current ripple, arising from the low frequency bus voltage ripple. Experimental results are presented with the topology operating under output dimming and reduced DC-link capacitance.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Two-stage digitally controlled led driver based on buck-boost and DC/DC LLC resonant converter
In this study a digitally controlled Light Emitting Diode (LED) driver operating with high power factor, dimming capability and reduced DC-link capacitance is proposed. The proposed LED driver circuit topology, designed to supply a 100 W LED module, is composed by two independent stages. The Power Factor Correction stage is implemented with the buck-boost DC/DC converter, operating in Discontinuous Conduction Mode. This stage provide a high power factor and maintain the average bus voltage controlled in 400 V. Besides, a reduce DC-link capacitance with 25 μF is used, thus allowing the use of log lifetime film capacitors. The second stage comprises the DC/DC Half-Bridge LLC resonant converter, which is in charge to keep controlled the averaged LED current as function of the required dimming level. To avoid output luminous intensity modulation, the control loop of the second stage is designed in order to reduce the LED current ripple, arising from the low frequency bus voltage ripple. Experimental results are presented with the topology operating under output dimming and reduced DC-link capacitance.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 3629-3634
Universal input voltage LED driver with dimming capability and reduced DC-link capacitance
This paper presents a digitally controlled Light Emitting Diode (LED) driver with high power factor, universal input voltage, dimming capability and reduced DC-link storage energy capacitance. A two-stage structure composed by the Power Factor Correction and Power Control stages is proposed. The buck-boost DC/DC converter, operating in Discontinuous Conduction Mode is employed for power factor correction, and is responsible for maintain the average bus voltage controlled in 400 V, as function of the input universal voltage (85 - 265 V RMS ). The DC/DC Half-Bridge LLC converter composes the power control stage, which is in charged to keep controlled the averaged LED current as function of the required dimming level. Furthermore, the low frequency bus voltage ripple is compensated in this stage through a properly closed loop design. Simulations results are presented with the topology operating under universal input voltage, output dimming, and reduced DC-link capacitance.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 3629-3634
Universal input voltage LED driver with dimming capability and reduced DC-link capacitance
This paper presents a digitally controlled Light Emitting Diode (LED) driver with high power factor, universal input voltage, dimming capability and reduced DC-link storage energy capacitance. A two-stage structure composed by the Power Factor Correction and Power Control stages is proposed. The buck-boost DC/DC converter, operating in Discontinuous Conduction Mode is employed for power factor correction, and is responsible for maintain the average bus voltage controlled in 400 V, as function of the input universal voltage (85 - 265 V RMS ). The DC/DC Half-Bridge LLC converter composes the power control stage, which is in charged to keep controlled the averaged LED current as function of the required dimming level. Furthermore, the low frequency bus voltage ripple is compensated in this stage through a properly closed loop design. Simulations results are presented with the topology operating under universal input voltage, output dimming, and reduced DC-link capacitance.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Improved design considerations for a self-oscillating resonant converter
This paper presents an improved design approach for the self-oscillating command circuit, suitable for high self-sustained frequency, where the influence of the MOSFET gate-to-source capacitance is considered. The operation at high frequency presents the advantages as reduced size and weight for power electronics converters, for instance resonant converter. Furthermore, the use of the self-oscillating command circuit add low cost feature to the system. The self-oscillating resonant converter is designed by using the describing-function method and extended Nyquist stability criterion. Where, it allows the design of the system in a self-sustained operation point as well to predict more accurately the self-oscillating frequency.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Improved design considerations for a self-oscillating resonant converter
This paper presents an improved design approach for the self-oscillating command circuit, suitable for high self-sustained frequency, where the influence of the MOSFET gate-to-source capacitance is considered. The operation at high frequency presents the advantages as reduced size and weight for power electronics converters, for instance resonant converter. Furthermore, the use of the self-oscillating command circuit add low cost feature to the system. The self-oscillating resonant converter is designed by using the describing-function method and extended Nyquist stability criterion. Where, it allows the design of the system in a self-sustained operation point as well to predict more accurately the self-oscillating frequency.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Fluorescent lamp characterization automated data acquisition system
The data acquisition process is an important step in the development of device models, and usually requires large amounts of time. Besides, since it is a process controlled by a scientist, it is subject to human errors. The automation of this process by a configurable system removes the human error factor and does not require full time attention from the scientist. These drawbacks are more evident when a device has to be modeled under various conditions, has a slow thermal response or a large database of various models has to be built. In this scope, the objective of this paper is to present the structure and results of an automated data acquisition system for fluorescent lamps. The aim of this system is to generate a database, which will be used in further studies of universal electronic ballasts.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Fluorescent lamp characterization automated data acquisition system
The data acquisition process is an important step in the development of device models, and usually requires large amounts of time. Besides, since it is a process controlled by a scientist, it is subject to human errors. The automation of this process by a configurable system removes the human error factor and does not require full time attention from the scientist. These drawbacks are more evident when a device has to be modeled under various conditions, has a slow thermal response or a large database of various models has to be built. In this scope, the objective of this paper is to present the structure and results of an automated data acquisition system for fluorescent lamps. The aim of this system is to generate a database, which will be used in further studies of universal electronic ballasts.