Okan Gul
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Okan Gul has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Sinan Yilmaz
Kocaeli University
3 shared publications Taner Yilmaz
Department of Mechanical Engineering Faculty of Engineering Kocaeli University Kocaeli 41001 Turkey
3 shared publications- Taner Yilmaz
Department of Mechanical Engineering, Faculty of Engineering, Kocaeli University, Kocaeli, Turkey
3 shared publications - Nevin Gamze Karsli
Department of Aviation and Aerospace Engineering, Faculty of Aviation and Aerospace Sciences Kocaeli University Kocaeli Turkey
2 shared publications - Ali Durmuş
Department of Mechanical Engineering, Bursa Uludag University, Bursa, Turkey
1 shared publication Busra Eyri
Department of Mechanical Engineering Faculty of Engineering Kocaeli University Kocaeli 41001 Turkey
1 shared publication
Latest Publications
- 6 December 2025
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 32 (2) , 484-498
Investigation of Mechanical Properties in Layered Multi‐Material 3D Printing Using Commercial Filaments: Direct Stacking of ABS , PA , and Compatibilizing Layers
Fused filament fabrication (FFF) technology has rapidly progressed in software and equipment, driven by increasing demand across industries and households. However, the development of compatible and high‐performance materials has lagged, limiting the mechanical integrity and design flexibility of printed components. To address this issue, this study investigates the interfacial bonding behavior of multi‐material structures composed of acrylonitrile butadiene styrene (ABS) and polyamide (PA), two polymers that are chemically incompatible. To enhance interfacial adhesion, three commonly used thermoplastic filaments were employed as intermediate compatibilizing layers. Mechanical characterization was performed through tensile and interlaminar shear strength tests to evaluate bonding performance. All compatibilizing layers improved adhesion between ABS and PA, yielding up to 32% higher tensile strength and 43% higher interlaminar shear strength compared to direct stacking. Fractographic observations confirmed these results by revealing distinct failure patterns and improved interfacial continuity. Overall, the findings demonstrate a practical method for achieving strong adhesion between incompatible polymers without surface treatments or adhesives, offering guidance for the design of hybrid structures and expanding the potential of the technology.
- 6 December 2025
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 32 (2) , 484-498
Investigation of Mechanical Properties in Layered Multi‐Material 3D Printing Using Commercial Filaments: Direct Stacking of ABS , PA , and Compatibilizing Layers
Fused filament fabrication (FFF) technology has rapidly progressed in software and equipment, driven by increasing demand across industries and households. However, the development of compatible and high‐performance materials has lagged, limiting the mechanical integrity and design flexibility of printed components. To address this issue, this study investigates the interfacial bonding behavior of multi‐material structures composed of acrylonitrile butadiene styrene (ABS) and polyamide (PA), two polymers that are chemically incompatible. To enhance interfacial adhesion, three commonly used thermoplastic filaments were employed as intermediate compatibilizing layers. Mechanical characterization was performed through tensile and interlaminar shear strength tests to evaluate bonding performance. All compatibilizing layers improved adhesion between ABS and PA, yielding up to 32% higher tensile strength and 43% higher interlaminar shear strength compared to direct stacking. Fractographic observations confirmed these results by revealing distinct failure patterns and improved interfacial continuity. Overall, the findings demonstrate a practical method for achieving strong adhesion between incompatible polymers without surface treatments or adhesives, offering guidance for the design of hybrid structures and expanding the potential of the technology.
- 28 August 2024
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (17) , 16219-16239
Study of the effect of hexagonal boron nitride addition to thermoplastic polyester elastomer composites reinforced with carbon, glass and basalt fibers
- 28 August 2024
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (17) , 16219-16239
Study of the effect of hexagonal boron nitride addition to thermoplastic polyester elastomer composites reinforced with carbon, glass and basalt fibers
- Open Access
- 5 February 2024
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 309 (5)
Analyzing the Influence of Multimaterial 3D Printing and Postprocessing on Mechanical and Tribological Characteristics
3D printing has witnessed a remarkable surge in popularity due to its flexibility in design and adaptability as a manufacturing technique to nearly each industrial area. This study focuses on harnessing the technological versatility of 3D printing by utilizing both standard poly lactic acid (PLA) and copper powder‐doped PLA to fabricate intricate structures through a layer‐by‐layer additive manufacturing process. The other innovation introduced here lies in the postprocessing step, which involves salt remelting. The mechanical properties of 3D‐printed standard test specimens undergo comprehensive assessment, encompassing bending and tensile evaluations, hardness measurements, density assessments, dimensional stability analyses, and wear resistance examinations. Utilizing copper powder‐doped PLA for the initial and final layers in XYZ‐oriented prints enables multimaterial printing, resulting in an ≈14% increase in tensile strength. Subsequently, subjecting this multimaterial composite to salt remelting elevates the strength enhancement to ≈16%, accompanied by a significant boost in rigidity by reducing voids in cross‐sectional area. In addition, scanning electron microscope images are captured, allowing for a detailed morphological analysis, which is then correlated with the findings of the various tests performed. This research unveils the potential of 3D printing technology in crafting materials with tailored mechanical properties, advancing its applicability in numerous industrial sectors.
- 5 February 2024
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 309 (5)
Open AccessAnalyzing the Influence of Multimaterial 3D Printing and Postprocessing on Mechanical and Tribological Characteristics
3D printing has witnessed a remarkable surge in popularity due to its flexibility in design and adaptability as a manufacturing technique to nearly each industrial area. This study focuses on harnessing the technological versatility of 3D printing by utilizing both standard poly lactic acid (PLA) and copper powder‐doped PLA to fabricate intricate structures through a layer‐by‐layer additive manufacturing process. The other innovation introduced here lies in the postprocessing step, which involves salt remelting. The mechanical properties of 3D‐printed standard test specimens undergo comprehensive assessment, encompassing bending and tensile evaluations, hardness measurements, density assessments, dimensional stability analyses, and wear resistance examinations. Utilizing copper powder‐doped PLA for the initial and final layers in XYZ‐oriented prints enables multimaterial printing, resulting in an ≈14% increase in tensile strength. Subsequently, subjecting this multimaterial composite to salt remelting elevates the strength enhancement to ≈16%, accompanied by a significant boost in rigidity by reducing voids in cross‐sectional area. In addition, scanning electron microscope images are captured, allowing for a detailed morphological analysis, which is then correlated with the findings of the various tests performed. This research unveils the potential of 3D printing technology in crafting materials with tailored mechanical properties, advancing its applicability in numerous industrial sectors.
- 17 January 2018
- Published by Springer Nature in Polymer Bulletin
- Vol. 75 (10) , 4429-4444
Effects of coupling agent addition on the adhesive wear, frictional and thermal properties of glass fiber-reinforced polyamide 6,6 composites
- 17 January 2018
- Published by Springer Nature in Polymer Bulletin
- Vol. 75 (10) , 4429-4444
Effects of coupling agent addition on the adhesive wear, frictional and thermal properties of glass fiber-reinforced polyamide 6,6 composites
- Open Access
- 1 April 2015
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 127 (4) , 1121-1123
Effect of CBC and G-POSS on Tribological Behaviour of Polyamide 6 and Short Glass Fiber Reinforced Polyamide 6 Composites
- 1 April 2015
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 127 (4) , 1121-1123
Open AccessEffect of CBC and G-POSS on Tribological Behaviour of Polyamide 6 and Short Glass Fiber Reinforced Polyamide 6 Composites
- 1 January 2014
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 125 (2) , 491-493
The Effect of Low Temperature Plasma Nitriding on Wear Resistance of Ti6Al4V Alloy
- 1 January 2014
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 125 (2) , 491-493
The Effect of Low Temperature Plasma Nitriding on Wear Resistance of Ti6Al4V Alloy