Sudhakar Natarajan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sudhakar Natarajan has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Natarajan Rajasekar
Vellore Institute of Technology
7 shared publications - Kalvakurthi Jyotheeswara Reddy
School of Electrical and Electronics Engineering, REVA University, Bengaluru, India
6 shared publications K. Jyotheeswara Reddy
3 shared publications- Thanikanti Sudhakar Babu
Chaitanya Bharathi Institute of Technology
3 shared publications - Karthik Balasubramanian
Offshore Technology Development Private Ltd., Keppel Offshore and Marine Ltd., Singapore
2 shared publications - Padmavathi Pydikalva
Deapartment of Electrical and Electronics Engineering, Srinivasa Ramanujan Institute of Technology, (Autonomous) Andhra Pradesh, India
2 shared publications
Latest Publications
- Open Access
- 30 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 51126-51142
ARM-Powered Chaotic PWM: A Simplified Solution for EMI Reduction in High-Gain DC-DC Converters
In this paper a simplified Chaotic Pulse Width Modulation (CPWM) method is proposes for minimizing conducted electromagnetic interference (EMI) in high-gain DC-DC converters, address the shortcomings of traditional PWM techniques. In contrast to conventional methods, CPWM uses deterministic chaos to randomize switching pulses, which efficiently distributes spectrum energy and reduces high-frequency harmonic peaks without changing the output voltage and convertor performance. A randomized carrier frequency modulation with a fixed duty ratio (RCFMFD) technique is used for achieving spectral spreading with minimum hardware complexity. The proposed high-gain converter is modelled and simulated in MATLAB/Simulink under periodic and chaotic PWM settings. A hardware prototype is developed with a DC input of 12 V and it was stepped up to a 200 V DC at a 200 kHz switching frequency with a 35% duty cycle. An ARM based processor generates both conventional and CPWM switching pulses, interfaced to the MOSFET gate through a driver. A power spectral density (PSD) comparison reveals that CPWM achieves a maximum conducted EMI suppression of about 23.08 dBμV (equivalent to 22.6 μV) compared to conventional PWM. The results verify that CPWM offers a compact, cost-effective, and high-performance EMI suppression solution suitable for EMI-sensitive applications such as electric vehicles, aerospace, and medical electronics.
- 30 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 51126-51142
Open AccessARM-Powered Chaotic PWM: A Simplified Solution for EMI Reduction in High-Gain DC-DC Converters
In this paper a simplified Chaotic Pulse Width Modulation (CPWM) method is proposes for minimizing conducted electromagnetic interference (EMI) in high-gain DC-DC converters, address the shortcomings of traditional PWM techniques. In contrast to conventional methods, CPWM uses deterministic chaos to randomize switching pulses, which efficiently distributes spectrum energy and reduces high-frequency harmonic peaks without changing the output voltage and convertor performance. A randomized carrier frequency modulation with a fixed duty ratio (RCFMFD) technique is used for achieving spectral spreading with minimum hardware complexity. The proposed high-gain converter is modelled and simulated in MATLAB/Simulink under periodic and chaotic PWM settings. A hardware prototype is developed with a DC input of 12 V and it was stepped up to a 200 V DC at a 200 kHz switching frequency with a 35% duty cycle. An ARM based processor generates both conventional and CPWM switching pulses, interfaced to the MOSFET gate through a driver. A power spectral density (PSD) comparison reveals that CPWM achieves a maximum conducted EMI suppression of about 23.08 dBμV (equivalent to 22.6 μV) compared to conventional PWM. The results verify that CPWM offers a compact, cost-effective, and high-performance EMI suppression solution suitable for EMI-sensitive applications such as electric vehicles, aerospace, and medical electronics.
- 6 August 2025
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (4) , 2397-2419
A Comparative Analysis of Conducted EMI Mitigation Strategies in Nonisolated Power Converters
Electromagnetic interference (EMI) reduction is crucial in nonisolated power converters owing to their impact on both compliance and performance. High‐frequency switching in converters generates conducted EMI, which can interfere with nearby sensitive electronics, potentially leading to malfunction or failure. Additionally, failing to suppress EMI can result in converters not meeting electromagnetic compatibility (EMC) standards, limiting their application in regulated environments and affecting the overall product reliability and safety. Effective EMI reduction requires precise modeling of parasitic components such as MOSFETs, inductors, and cables, as these elements critically influence the EMI behavior in converters. Suppression techniques such as filtering, soft switching, and advanced modulation are evaluated not only for their efficacy in EMI attenuation but also for their impact on the converter performance, efficiency, and cost. This investigation provides a detailed analysis of conducted EMI suppression techniques specifically for boost, boost PFC, buck, and buck–boost converters. Emphasis is placed on advanced suppression strategies, including filtering, soft switching, random pulse width modulation (RPWM), and chaotic PWM (CPWM), each evaluated its effectiveness in reducing EMI while maintaining the converter efficiency. This review paper offers a foundation for implementing EMC‐compliant power electronics designs that address conducted EMI challenges.
- 6 August 2025
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (4) , 2397-2419
A Comparative Analysis of Conducted EMI Mitigation Strategies in Nonisolated Power Converters
Electromagnetic interference (EMI) reduction is crucial in nonisolated power converters owing to their impact on both compliance and performance. High‐frequency switching in converters generates conducted EMI, which can interfere with nearby sensitive electronics, potentially leading to malfunction or failure. Additionally, failing to suppress EMI can result in converters not meeting electromagnetic compatibility (EMC) standards, limiting their application in regulated environments and affecting the overall product reliability and safety. Effective EMI reduction requires precise modeling of parasitic components such as MOSFETs, inductors, and cables, as these elements critically influence the EMI behavior in converters. Suppression techniques such as filtering, soft switching, and advanced modulation are evaluated not only for their efficacy in EMI attenuation but also for their impact on the converter performance, efficiency, and cost. This investigation provides a detailed analysis of conducted EMI suppression techniques specifically for boost, boost PFC, buck, and buck–boost converters. Emphasis is placed on advanced suppression strategies, including filtering, soft switching, random pulse width modulation (RPWM), and chaotic PWM (CPWM), each evaluated its effectiveness in reducing EMI while maintaining the converter efficiency. This review paper offers a foundation for implementing EMC‐compliant power electronics designs that address conducted EMI challenges.
- Open Access
- 9 September 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-21
Golden eagle optimized fractional-order PI controller design for a PFC SEPIC converter in EV charging
The power factor correction converter is the function of the front-end converter, followed by the DC–DC converter of the electric vehicle charger. It improves the power factor and regulates the output voltage and current. This research article proposes the Golden Eagle optimization for fractional order PI (FOPI) controller for Single Ended Primary Inductor Converter (SEPIC) power factor correction. The Golden eagle optimization is based on its knowledge of hunting tactics at various degrees of spiral trajectories to catch the prey. The FOPI controller has a broad range of controller parameters that provide better control and performance of the converter. The tuning of the parameters of the FOPI controller is optimized in Golden Eagle Optimization, and the Integral Absolute error with Integral Square error is used for the objective function. The optimized parameters of FOPI compare with the conventional PI controller performance. The SEPIC converter is designed and derived from the state space model by state space averaging, and the reduced model is obtained through the moment matching method. This system is tested under MATLAB/SIMULINK, and simulation results show improved settling time, fast dynamic response, reduction of inrush current, less harmonic distortion, and stability.
- 9 September 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-21
Open AccessGolden eagle optimized fractional-order PI controller design for a PFC SEPIC converter in EV charging
The power factor correction converter is the function of the front-end converter, followed by the DC–DC converter of the electric vehicle charger. It improves the power factor and regulates the output voltage and current. This research article proposes the Golden Eagle optimization for fractional order PI (FOPI) controller for Single Ended Primary Inductor Converter (SEPIC) power factor correction. The Golden eagle optimization is based on its knowledge of hunting tactics at various degrees of spiral trajectories to catch the prey. The FOPI controller has a broad range of controller parameters that provide better control and performance of the converter. The tuning of the parameters of the FOPI controller is optimized in Golden Eagle Optimization, and the Integral Absolute error with Integral Square error is used for the objective function. The optimized parameters of FOPI compare with the conventional PI controller performance. The SEPIC converter is designed and derived from the state space model by state space averaging, and the reduced model is obtained through the moment matching method. This system is tested under MATLAB/SIMULINK, and simulation results show improved settling time, fast dynamic response, reduction of inrush current, less harmonic distortion, and stability.
- Open Access
- 1 August 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (4) , 3838-3846
Conducted electromagnetic interference mitigation in super-lift Luo-converter for electric vehicle applications
In this article, a digital chaotic pulse width modulation (DCPWM)-dependent electromagnetic interference (EMI) noise attenuating procedure has been implemented. With the aid of a field programmable gate array (FPGA), a randomized carrier frequency modulation with a fixed duty cycle has been generated through chaotic carrier frequency, and this process is called DCPWM. Conducted EMI suppression is achieved in a 200 kHz, 40 W elementary positive output super lift Luo (EPOSLL) converter using the DCPWM technique. The results are compared and validated with periodic PWM over DCPWM in simulation and hardware with electromagnetic compatibility (EMC) standards. Besides, 9 dBV (2.81 V) of conducted EMI noise has been minimized in the DCPWM approach against periodic pulse width modulation method for the EPOSLL converter in electric vehicles applications.
- 1 August 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (4) , 3838-3846
Open AccessConducted electromagnetic interference mitigation in super-lift Luo-converter for electric vehicle applications
In this article, a digital chaotic pulse width modulation (DCPWM)-dependent electromagnetic interference (EMI) noise attenuating procedure has been implemented. With the aid of a field programmable gate array (FPGA), a randomized carrier frequency modulation with a fixed duty cycle has been generated through chaotic carrier frequency, and this process is called DCPWM. Conducted EMI suppression is achieved in a 200 kHz, 40 W elementary positive output super lift Luo (EPOSLL) converter using the DCPWM technique. The results are compared and validated with periodic PWM over DCPWM in simulation and hardware with electromagnetic compatibility (EMC) standards. Besides, 9 dBV (2.81 V) of conducted EMI noise has been minimized in the DCPWM approach against periodic pulse width modulation method for the EPOSLL converter in electric vehicles applications.
- 9 May 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 47 (3) , 1009-1020
Multi-Level Active EMI Filter for Conducted EMI Noise Mitigation for TSCB Converter in EV Applications
- 9 May 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 47 (3) , 1009-1020
Multi-Level Active EMI Filter for Conducted EMI Noise Mitigation for TSCB Converter in EV Applications
- 5 April 2023
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 51 (11) , 1051-1074
PV-Fed Micro-Inverter with Battery Storage for Single Phase Grid Applications
Nowadays, micro-inverters are trending due to the latest features consisting in PV technology. However, integration of a high-gain boost converter is needed to improve the low rating output voltage of PV modules to meet the load demand. A high-gain converter with less component count is required for grid integration systems. This article proposes a new quasi z-source based high-gain DC–DC converter with reduced components, cost, and size. The proposed converter is integrated with the micro-inverter for single-phase grid applications along with battery storage. A radial basis function network algorithm is utilized for a PV system to track the maximum power point, an efficient hysteresis current controller is applied for the full-bridge inverter for the robust regulation of current and the energy can be stored through the bidirectional dc/dc converter to supply the power to grid when the sources are drained conditions. An efficient PV extraction, low total harmonic distortion and achieves unity power factor which is perfectly suitable for grid-connected PV systems. The operating modes in every aspect and analysis of the proposed configuration have been investigated in detail. The implementation of control strategies is discussed in detail. Simulation of the proposed micro-inverter is designed in MATLAB/SIMULINK tool to validate the efficiency under variable operating conditions. With the successful implementation of the proposed technique, total harmonic distortion is reduced to 2.05% and efficiency is enhance to the 98%.
- 5 April 2023
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 51 (11) , 1051-1074
PV-Fed Micro-Inverter with Battery Storage for Single Phase Grid Applications
Nowadays, micro-inverters are trending due to the latest features consisting in PV technology. However, integration of a high-gain boost converter is needed to improve the low rating output voltage of PV modules to meet the load demand. A high-gain converter with less component count is required for grid integration systems. This article proposes a new quasi z-source based high-gain DC–DC converter with reduced components, cost, and size. The proposed converter is integrated with the micro-inverter for single-phase grid applications along with battery storage. A radial basis function network algorithm is utilized for a PV system to track the maximum power point, an efficient hysteresis current controller is applied for the full-bridge inverter for the robust regulation of current and the energy can be stored through the bidirectional dc/dc converter to supply the power to grid when the sources are drained conditions. An efficient PV extraction, low total harmonic distortion and achieves unity power factor which is perfectly suitable for grid-connected PV systems. The operating modes in every aspect and analysis of the proposed configuration have been investigated in detail. The implementation of control strategies is discussed in detail. Simulation of the proposed micro-inverter is designed in MATLAB/SIMULINK tool to validate the efficiency under variable operating conditions. With the successful implementation of the proposed technique, total harmonic distortion is reduced to 2.05% and efficiency is enhance to the 98%.
- Open Access
- 1 April 2023
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 12 (2) , 704-718
A comparison statement on DCPWM based conducted EMI noise mitigation process in DC-DC converters for EV
Fast switching techniques at high frequencies are employed for quick charging and energy conversion in electric vehicle (EV) power converters. Electromagnetic interference (EMI) noise is produced due to the fast-switching process, which may result in malfunctioning and degraded EV performance. In this work, a digital chaotic pulse width modulation (DCPWM) technique-based EMI noise mitigation process has been applied to elementary positive output super lift Luo (EPOSLL), two-stage cascaded boost (TSCB), and ultra-lift Luo (ULL) converters, and a comparison study has been conducted with EMI reduction levels as per electromagnetic compatibility (EMC) standards. The duty cycle is varied from 0.5 to 0.67 to get the desired output voltage as an input of 10V to achieve the power ratings of 40 W to 80 W for various load conditions. A total of 4 dBV (3 V) to 15 dBV (10 V) of conducted EMI noise has been mitigated for the above-said converters. Simulation results based on power spectrum density and hardware results based on fast fourier transform (FFT) of output voltages are analyzed. According to the findings, the ULL converter is more acceptable for electromagnetic compatibility in EV applications than EPOSLL and TSCB DC-DC converters.
- 1 April 2023
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 12 (2) , 704-718
Open AccessA comparison statement on DCPWM based conducted EMI noise mitigation process in DC-DC converters for EV
Fast switching techniques at high frequencies are employed for quick charging and energy conversion in electric vehicle (EV) power converters. Electromagnetic interference (EMI) noise is produced due to the fast-switching process, which may result in malfunctioning and degraded EV performance. In this work, a digital chaotic pulse width modulation (DCPWM) technique-based EMI noise mitigation process has been applied to elementary positive output super lift Luo (EPOSLL), two-stage cascaded boost (TSCB), and ultra-lift Luo (ULL) converters, and a comparison study has been conducted with EMI reduction levels as per electromagnetic compatibility (EMC) standards. The duty cycle is varied from 0.5 to 0.67 to get the desired output voltage as an input of 10V to achieve the power ratings of 40 W to 80 W for various load conditions. A total of 4 dBV (3 V) to 15 dBV (10 V) of conducted EMI noise has been mitigated for the above-said converters. Simulation results based on power spectrum density and hardware results based on fast fourier transform (FFT) of output voltages are analyzed. According to the findings, the ULL converter is more acceptable for electromagnetic compatibility in EV applications than EPOSLL and TSCB DC-DC converters.
- 17 October 2022
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 18 (3) , 2003-2013
Conducted Electromagnetic Interference Mitigation on Two-Stage Cascaded Boost (TSCB) DC-DC Converter Using FPGA Based DCPWM Technique for EV Applications
- 17 October 2022
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 18 (3) , 2003-2013
Conducted Electromagnetic Interference Mitigation on Two-Stage Cascaded Boost (TSCB) DC-DC Converter Using FPGA Based DCPWM Technique for EV Applications
- Open Access
- 12 October 2022
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 10
A review on unidirectional converters for on-board chargers in electric vehicle
Transport is a vital sector for achieving sustainable development. The evolution of the electric vehicle is subject to the charging time, accessibility, and facility. On-board chargers are broadly used in the battery-electric and plug-in-electric fleets due to their easy installation and low cost. Also, it must be powerful and extremely efficient because of the constrained interior area and quick charging times. The minimization of hardware requirements and ease of interconnection problems are benefits of unidirectional charging. This review article presents an overview of charging levels, standards of chargers, and various topologies. On-board chargers pose a higher-power rating that reduces the anxiety of charging time and improves the charging facility on level-1 and level-2 grid supply. Unidirectional chargers reduce the charger size while other two-stage chargers pose a higher charging rate with various topologies. Finally, emerging charging trends in off-board charging, inductive charging, technology about vehicle-to-grid, wide-bandgap devices, and application of renewable energy uses are addressed.
- 12 October 2022
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 10
Open AccessA review on unidirectional converters for on-board chargers in electric vehicle
Transport is a vital sector for achieving sustainable development. The evolution of the electric vehicle is subject to the charging time, accessibility, and facility. On-board chargers are broadly used in the battery-electric and plug-in-electric fleets due to their easy installation and low cost. Also, it must be powerful and extremely efficient because of the constrained interior area and quick charging times. The minimization of hardware requirements and ease of interconnection problems are benefits of unidirectional charging. This review article presents an overview of charging levels, standards of chargers, and various topologies. On-board chargers pose a higher-power rating that reduces the anxiety of charging time and improves the charging facility on level-1 and level-2 grid supply. Unidirectional chargers reduce the charger size while other two-stage chargers pose a higher charging rate with various topologies. Finally, emerging charging trends in off-board charging, inductive charging, technology about vehicle-to-grid, wide-bandgap devices, and application of renewable energy uses are addressed.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Peptide-Based Direct Electrochemical Detection of Receptor Binding Domains of SARS-CoV-2 Spike Protein in Pristine Samples
RNA isolation and amplification-free user-friendly detection of SARS-CoV-2 is the need of hour especially at resource limited settings. Herein, we devised the peptides of human angiotensin converting enzyme-2 (hACE-2) as bioreceptor at electrode interface for selective targeting of receptor binding domains (RBD) of SARS-CoV-2 spike protein (SP). Disposable carbon-screen printed electrode modified with methylene blue (MB) electroadsorbed graphene oxide (GO) has been constructed as cost-efficient and scalable platform for hACE-2 peptide-based SARS-CoV-2 detection. In silico molecular docking of customized 25 mer peptides with RBD of SARS-CoV-2 SP were validated by AutoDock CrankPep. N-terminal region of ACE-2 showed higher binding affinity of -20.6 kcal/mol with 15 H-bond, 9 of which were hACE-2 peptide platform exert an enhanced current sensitivity of 0.0105 mA/pg mL-1 cm-2 (R2 = 0.9792) (CV) and 0.45 nA/pg mL-1 (R2 = 0.9570) (CA) against SP in the range of 1 pg/mL to 1 µg/mL. For clinical feasibility, nasopharyngeal and oropharyngeal swab specimens in viral transport medium were directly tested with the prepared peptide biosensor and validated with RT-PCR, promising for point-of-need analysis.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessPeptide-Based Direct Electrochemical Detection of Receptor Binding Domains of SARS-CoV-2 Spike Protein in Pristine Samples
RNA isolation and amplification-free user-friendly detection of SARS-CoV-2 is the need of hour especially at resource limited settings. Herein, we devised the peptides of human angiotensin converting enzyme-2 (hACE-2) as bioreceptor at electrode interface for selective targeting of receptor binding domains (RBD) of SARS-CoV-2 spike protein (SP). Disposable carbon-screen printed electrode modified with methylene blue (MB) electroadsorbed graphene oxide (GO) has been constructed as cost-efficient and scalable platform for hACE-2 peptide-based SARS-CoV-2 detection. In silico molecular docking of customized 25 mer peptides with RBD of SARS-CoV-2 SP were validated by AutoDock CrankPep. N-terminal region of ACE-2 showed higher binding affinity of -20.6 kcal/mol with 15 H-bond, 9 of which were hACE-2 peptide platform exert an enhanced current sensitivity of 0.0105 mA/pg mL-1 cm-2 (R2 = 0.9792) (CV) and 0.45 nA/pg mL-1 (R2 = 0.9570) (CA) against SP in the range of 1 pg/mL to 1 µg/mL. For clinical feasibility, nasopharyngeal and oropharyngeal swab specimens in viral transport medium were directly tested with the prepared peptide biosensor and validated with RT-PCR, promising for point-of-need analysis.