Sybille Hellebrand
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sybille Hellebrand has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Hans-Joachim Wunderlich
University of Stuttgart, Stuttgart, Germany
7 shared publications - Hussam Amrouch
Technical University of Munich
3 shared publications - Matthias Kampmann
Paderborn University, Paderborn, Germany
3 shared publications - Florian Klemme
Siemens EDA, Hamburg, Germany
2 shared publications Jan Dennis Reimer
Paderborn University,Paderborn,Germany,33098
2 shared publications- Somayeh Sadeghi-Kohan
Paderborn University, Paderborn, Germany
2 shared publications
Latest Publications
- Open Access
- 1 June 2026
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 42 (3) , 405-416
Robust Adaptive DLBIST for Delay Fault Testing: Minimizing PVT Variability with Zero Temperature Coefficient (ZTC) Voltage
Safety-critical automotive systems require on-chip testing methods to ensure high fault coverage and reliable operation. Periodic Deterministic Logic Built-In Self-Test (DLBIST) is often used to meet these demands. For automotive applications, DLBIST must operate reliably despite temperature variations, including those caused by ambient changes and self-heating in FinFET transistors. A test set effective for all temperatures typically requires a large volume, which can make DLBIST impractical. This paper proposes a robust DLBIST scheme which applies multiple voltages during power-on and power-off tests and the optimal or adapted voltage during periodic tests in system operation. If distributed sensors for on-chip temperature are available for DVFS control, they can be exploited for an adaptive DLBIST scheme. During the periodic test phase, the BIST Control Unit (BCU) dynamically selects and applies the pre-generated test set corresponding to the current operating voltage and measured temperature. This adaptive selection ensures that testing conditions precisely match the real operating points. If temperature sensors are not available, testing at the so-called Zero Temperature Coefficient (ZTC) voltage is one alternative, which is the voltage where the temperature-induced variability is minimized. This makes periodic DLBIST a feasible solution for in-field self-testing, even in cases where on-chip temperature sensors are not available.
- 1 June 2026
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 42 (3) , 405-416
Open AccessRobust Adaptive DLBIST for Delay Fault Testing: Minimizing PVT Variability with Zero Temperature Coefficient (ZTC) Voltage
Safety-critical automotive systems require on-chip testing methods to ensure high fault coverage and reliable operation. Periodic Deterministic Logic Built-In Self-Test (DLBIST) is often used to meet these demands. For automotive applications, DLBIST must operate reliably despite temperature variations, including those caused by ambient changes and self-heating in FinFET transistors. A test set effective for all temperatures typically requires a large volume, which can make DLBIST impractical. This paper proposes a robust DLBIST scheme which applies multiple voltages during power-on and power-off tests and the optimal or adapted voltage during periodic tests in system operation. If distributed sensors for on-chip temperature are available for DVFS control, they can be exploited for an adaptive DLBIST scheme. During the periodic test phase, the BIST Control Unit (BCU) dynamically selects and applies the pre-generated test set corresponding to the current operating voltage and measured temperature. This adaptive selection ensures that testing conditions precisely match the real operating points. If temperature sensors are not available, testing at the so-called Zero Temperature Coefficient (ZTC) voltage is one alternative, which is the voltage where the temperature-induced variability is minimized. This makes periodic DLBIST a feasible solution for in-field self-testing, even in cases where on-chip temperature sensors are not available.
- Open Access
- 1 April 2025
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 41 (2) , 209-219
Small Delay Fault Testing with Multiple Voltages under Variations: Defect vs. Fault Coverage
It has been known and explored for many years that low voltage testing amplifies the effect of a defect, increasing the size of a Small Delay Fault (SDF) and, in the best case, turning SDFs into easily detectable stuck-at-faults. It is often overlooked that $$V_{\textrm{min}}$$ testing poses an additional challenge to the test pattern generation method under process variations. The standard deviation of gate delays under $$V_{\textrm{min}}$$ is a multiple of that under nominal voltage. The increased variation will invalidate the efficiency of test patterns generated under nominal voltage and significantly reduce fault coverage. This paper presents the first algorithm for test pattern generation specifically tuned for $$V_{\textrm{min}}$$ testing which obtains higher fault coverage by smaller test sets than those generated for nominal voltage. The patterns applicable to other voltage levels can be derived from the pattern set generated under extreme variations at low supply voltage. Experimental results demonstrate that the proposed method produces test patterns that outperform N-detection test sets in terms of test set volume and fault efficiency across different voltage levels.- 1 April 2025
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 41 (2) , 209-219
Open AccessSmall Delay Fault Testing with Multiple Voltages under Variations: Defect vs. Fault Coverage
It has been known and explored for many years that low voltage testing amplifies the effect of a defect, increasing the size of a Small Delay Fault (SDF) and, in the best case, turning SDFs into easily detectable stuck-at-faults. It is often overlooked that $$V_{\textrm{min}}$$ testing poses an additional challenge to the test pattern generation method under process variations. The standard deviation of gate delays under $$V_{\textrm{min}}$$ is a multiple of that under nominal voltage. The increased variation will invalidate the efficiency of test patterns generated under nominal voltage and significantly reduce fault coverage. This paper presents the first algorithm for test pattern generation specifically tuned for $$V_{\textrm{min}}$$ testing which obtains higher fault coverage by smaller test sets than those generated for nominal voltage. The patterns applicable to other voltage levels can be derived from the pattern set generated under extreme variations at low supply voltage. Experimental results demonstrate that the proposed method produces test patterns that outperform N-detection test sets in terms of test set volume and fault efficiency across different voltage levels. - 7 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 111-116
Robust Pattern Generation for Small Delay Faults Under Process Variations
Small Delay Faults (SDFs) introduce additional delays smaller than the capture time and require timing-aware test pattern generation. Since process variations can invalidate the effectiveness of such patterns, different circuit instances may show a different fault coverage for the same test pattern set. This paper presents a method to generate test pattern sets for SDFs which are valid for all circuit timings. The method overcomes the limitations of known timing-aware Automatic Test Pattern Generation (ATPG) which has to use fault sampling under process variations due to the computational complexity. A statistical learning scheme maximises the coverage of SDFs in circuits following the variation parameters of a calibrated industrial FinFET transistor model. The method combines efficient ATPG for Transition Faults (TFs) with fast timing-aware fault simulation on GPUs. Simulation experiments show that the size of the pattern set is significantly reduced in comparison to standard N-detection while the fault coverage even increases.
- 7 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 111-116
Robust Pattern Generation for Small Delay Faults Under Process Variations
Small Delay Faults (SDFs) introduce additional delays smaller than the capture time and require timing-aware test pattern generation. Since process variations can invalidate the effectiveness of such patterns, different circuit instances may show a different fault coverage for the same test pattern set. This paper presents a method to generate test pattern sets for SDFs which are valid for all circuit timings. The method overcomes the limitations of known timing-aware Automatic Test Pattern Generation (ATPG) which has to use fault sampling under process variations due to the computational complexity. A statistical learning scheme maximises the coverage of SDFs in circuits following the variation parameters of a calibrated industrial FinFET transistor model. The method combines efficient ATPG for Transition Faults (TFs) with fast timing-aware fault simulation on GPUs. Simulation experiments show that the size of the pattern set is significantly reduced in comparison to standard N-detection while the fault coverage even increases.
- 25 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Design & Test
- Vol. 41 (4) , 50-55
Workload-Aware Periodic Interconnect BIST
System-level interconnects provide the backbone for increasingly complex systems on a chip. Their vulnerability to electromigration and crosstalk can lead to serious reliability and safety issues during the system lifetime. This article presents an approach for periodic in-system testing which maintains a reliability profile to detect potential problems before they actually cause a failure. Relying on a common infrastructure for EM-aware system workload management and test, it minimizes the stress induced by the test itself and contributes to the self-healing of system-induced electromigration degradations.
- 25 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Design & Test
- Vol. 41 (4) , 50-55
Workload-Aware Periodic Interconnect BIST
System-level interconnects provide the backbone for increasingly complex systems on a chip. Their vulnerability to electromigration and crosstalk can lead to serious reliability and safety issues during the system lifetime. This article presents an approach for periodic in-system testing which maintains a reliability profile to detect potential problems before they actually cause a failure. Relying on a common infrastructure for EM-aware system workload management and test, it minimizes the stress induced by the test itself and contributes to the self-healing of system-induced electromigration degradations.
- Open Access
- 1 December 2021
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 37 (5-6) , 715-728
Stress-Aware Periodic Test of Interconnects
Safety-critical systems have to follow extremely high dependability requirements as specified in the standards for automotive, air, and space applications. The required high fault coverage at runtime is usually obtained by a combination of concurrent error detection or correction and periodic tests within rather short time intervals. The concurrent scheme ensures the integrity of computed results while the periodic test has to identify potential aging problems and to prevent any fault accumulation which may invalidate the concurrent error detection mechanism. Such periodic built-in self-test (BIST) schemes are already commercialized for memories and for random logic. The paper at hand extends this approach to interconnect structures. A BIST scheme is presented which targets interconnect defects before they will actually affect the system functionality at nominal speed. A BIST schedule is developed which significantly reduces aging caused by electromigration during the lifetime application of the periodic test.
- 1 December 2021
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 37 (5-6) , 715-728
Open AccessStress-Aware Periodic Test of Interconnects
Safety-critical systems have to follow extremely high dependability requirements as specified in the standards for automotive, air, and space applications. The required high fault coverage at runtime is usually obtained by a combination of concurrent error detection or correction and periodic tests within rather short time intervals. The concurrent scheme ensures the integrity of computed results while the periodic test has to identify potential aging problems and to prevent any fault accumulation which may invalidate the concurrent error detection mechanism. Such periodic built-in self-test (BIST) schemes are already commercialized for memories and for random logic. The paper at hand extends this approach to interconnect structures. A BIST scheme is presented which targets interconnect defects before they will actually affect the system functionality at nominal speed. A BIST schedule is developed which significantly reduces aging caused by electromigration during the lifetime application of the periodic test.
- 1 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Logic Fault Diagnosis of Hidden Delay Defects
Hidden delay defects (HDDs) are small delay defects that pass all at-speed tests at nominal capture time. They are an important indicator of latent defects that lead to early-life failures and aging problems that are serious especially in autonomous and medical applications. An effective way to screen out HDDs is to use Faster-than-At-Speed Testing (FAST) to observe outputs of sensitized non-critical paths which are expected to be stable earlier than nominal capture time.To improve the reliability of current and future designs, it is important to learn about the population of HDDs using logic diagnosis. We present the very first logic fault diagnosis technique that is able to identify HDDs by analyzing fail logs produced by FAST.Even with aggressive FAST testing, HDDs generate only very few failing test response bits. To overcome this severe challenge, we propose new backtracing and response matching methods that yield high diagnostic success rates even with very limited amount of failure data. The performance and scalability of our HDD diagnosis method is validated using fault injection campaigns with large benchmark circuits.
- 1 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Logic Fault Diagnosis of Hidden Delay Defects
Hidden delay defects (HDDs) are small delay defects that pass all at-speed tests at nominal capture time. They are an important indicator of latent defects that lead to early-life failures and aging problems that are serious especially in autonomous and medical applications. An effective way to screen out HDDs is to use Faster-than-At-Speed Testing (FAST) to observe outputs of sensitized non-critical paths which are expected to be stable earlier than nominal capture time.To improve the reliability of current and future designs, it is important to learn about the population of HDDs using logic diagnosis. We present the very first logic fault diagnosis technique that is able to identify HDDs by analyzing fail logs produced by FAST.Even with aggressive FAST testing, HDDs generate only very few failing test response bits. To overcome this severe challenge, we propose new backtracing and response matching methods that yield high diagnostic success rates even with very limited amount of failure data. The performance and scalability of our HDD diagnosis method is validated using fault injection campaigns with large benchmark circuits.
- 1 January 2018
- Published by Elsevier in Microelectronics Reliability
- Vol. 80, 124-133
Design for Small Delay Test - A Simulation Study
- 1 January 2018
- Published by Elsevier in Microelectronics Reliability
- Vol. 80, 124-133
Design for Small Delay Test - A Simulation Study
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 109-114
Optimized Selection of Frequencies for Faster-Than-at-Speed Test
Small gate delay faults (SDFs) are not detectable at-speed, if they can only be propagated along short paths. These hidden delay faults (HDFs) do not influence the circuit's behavior initially, but they may indicate design marginalities leading to early-life failures, and therefore they cannot be neglected. HDFs can be detected by faster-than-at-speed test (FAST), where typically several different frequencies are used to maximize the coverage. A given set of test patterns P potentially detects a HDF if it contains a test pattern sensitizing a path through the fault site, and the efficiency of FAST can be measured as the ratio of actually detected HDFs to potentially detected HDFs. The paper at hand targets maximum test efficiency with a minimum number of frequencies. The procedure starts with a test set for transition delay faults and a set of preselected equidistant frequencies. Timing-accurate simulation of this initial setup identifies the hard-to-detect faults, which are then targeted by a more complex timing-aware ATPG procedure. For the yet undetected HDFs, a minimum number of frequencies are determined using an efficient hypergraph algorithm. Experimental results show that with this approach, the number of test frequencies required for maximum test efficiency can be reduced considerably. Furthermore, test set inflation is limited as timing-aware ATPG is only used for a small subset of HDFs.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 109-114
Optimized Selection of Frequencies for Faster-Than-at-Speed Test
Small gate delay faults (SDFs) are not detectable at-speed, if they can only be propagated along short paths. These hidden delay faults (HDFs) do not influence the circuit's behavior initially, but they may indicate design marginalities leading to early-life failures, and therefore they cannot be neglected. HDFs can be detected by faster-than-at-speed test (FAST), where typically several different frequencies are used to maximize the coverage. A given set of test patterns P potentially detects a HDF if it contains a test pattern sensitizing a path through the fault site, and the efficiency of FAST can be measured as the ratio of actually detected HDFs to potentially detected HDFs. The paper at hand targets maximum test efficiency with a minimum number of frequencies. The procedure starts with a test set for transition delay faults and a set of preselected equidistant frequencies. Timing-accurate simulation of this initial setup identifies the hard-to-detect faults, which are then targeted by a more complex timing-aware ATPG procedure. For the yet undetected HDFs, a minimum number of frequencies are determined using an efficient hypergraph algorithm. Experimental results show that with this approach, the number of test frequencies required for maximum test efficiency can be reduced considerably. Furthermore, test set inflation is limited as timing-aware ATPG is only used for a small subset of HDFs.
- 23 July 2015
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 31 (4) , 349-359
A High Performance SEU Tolerant Latch
- 23 July 2015
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 31 (4) , 349-359
A High Performance SEU Tolerant Latch
- 30 September 2014
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 30 (5) , 527-540
Adaptive Bayesian Diagnosis of Intermittent Faults
- 30 September 2014
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 30 (5) , 527-540
Adaptive Bayesian Diagnosis of Intermittent Faults