KDKonstantin V. Dukel'Skii

Konstantin V. Dukel'Skii

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Konstantin V. Dukel'Skii has a total of 208 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Research of parameters of fusion splices of telecommunication multimode optical fibers and silica microstructured fiber lightguides with hexagonal configuration

    by A. V. Bourdine, V. G. Nesterov, M. A. Orlov, A. S. Evtushenko, S. S. Pashin, E. S. Zaitseva, A. A. Belyaev, D. N. Shurupov, V. V. Demidov, E. V. Ter-Nersesyants, et al.

    This work presents the results of experimental approbation of the ability to fuse telecommunication graded index multimode optical fibers of ISO/IEC Category OM2+/OM3 and silica microstructured optical fibers by using a commercially available field fusion splicer kit Fujikura-36S (Fujikura Ltd., Japan). We tested silica microstructured optical fiber with a hexagonal configuration that provides quasi-singlemode operation over an extended spectral band up to short wavelengths (λ = 800–1700 nm) in comparison with conventional singlemode optical fiber of ratified ITU-T Recommendations. The potential possibilities were explored for reducing of attenuation by selection and combination of fusion program parameters (arc current and arc time) to find a compromise between quality fusion splicing without any defects and minimization of insertion loss. About 1.5 m long short segment of researched microstructured optical fiber was spliced between two spools with multimode fibers, while each one of them was also spliced with two pigtailed spools with singlemode optical fibers. Fiber length of each spool was at the least 1 km long in order to provide insertion loss measurements by using optical time domain reflectometer EXFO AXS-110 (EXFO, Canad a). Based on a series of experiment, we have identified an optimal combination of arc current (STD-30 a.u.) and arc time (1100 ms) which provides desired compromise between reducing the fusion program parameters to prevent the MOF air hole collapsing under the quality splice without defects, and decreased insertion loss. As a result, the total insertion loss has been reduced to 0.8–1.0 dB and more in comparison with the reference value. For instance, mentioned above program settings gave the loss 5.721 dB under the reference value 6.722 dB. Therefore, the experimental results confirm ability of fusion splicing microstructured and multimode optical fibers with an acceptable insertion loss by using commercially available field fusion splicer kits. This provides to utilize proposed microstructured optical fibers with extended singlemode operation wavelength range in various applications of laser technology, optical devices and short-range high bit rate optical networks.

  • Spectral properties of 1,4-butanediol diglycidyl ether-based epoxy polymers and their multilayer glass composites

    by Valeriy M. Volynkin, Sergei K. Evstropiev, Dmitriy V. Bulyga, Grigorii S. Polishchuk, Konstantin V. Dukel’SKii

    Subject of study. 1,4-butanediol diglycidyl ether-based epoxy polymers and their multilayer glass composites were studied. Aim of study. The aim of this study was to obtain a new universal, homogeneous, and transparent epoxy composition with high adhesion to the surfaces of both organic and silicate glasses. In addition, the possibility of its application in the fabrication of homogeneous and transparent multilayer elements was investigated. Method. The investigations were conducted in the visible and infrared (IR) spectral regions using optical spectroscopy methods. The kinetics of the structural changes in the epoxy composition during polymerization were investigated by IR spectroscopy. Main results. The results showed that 80% of the structural changes, observed in the epoxy ring during the complete polymerization of its composition, occurred under isothermal exposure at 20°C in the first 160 min. Epoxy compositions with high adhesion to the surfaces of both organic and inorganic glasses were obtained. The compositions were used to fabricate multilayer glass-based materials transparent to visible light. Practical significance. The universal optical adhesive composition obtained in this study can be used for bonding both silicate glasses and organic glasses based on polymethyl methacrylate.

  • Open Access

    Synthesis and study of the structure and properties of photocatalytic nanocomposites of the Cu/ZnO-ZnCr2O4 system

    by S. K. Evstropyev, A. A. Shelemanov, N. V. Nikonorov, A. V. Karavaeva, К. В. Дукельский, G. S. Polischuk, M. A. Gavrilova, K. A. Portnova, I. V. Bagrov

    Currently, the development of new nanocomposite materials with improved photocatalytic and antibacterial properties is a topical task for environmentally friendly technologies for water and air purification. This paper presents the results of a study of ZnO-ZnCr2O4 and Cu/ZnO-ZnCr2O4 powder nanocomposites obtained by the polymer-salt method. For the synthesis of nanocomposites, zinc and chromium nitrate solutions with the addition of polyvinylpyrrolidone as a soluble organic polymer were used. The structure and morphology of the nanocomposites were studied by XRD analysis and electron microscopy, optical and luminescent properties using spectroscopic methods. As a result of heat treatment at 550 °С, dispersed powders of nanocomposites were obtained, consisting of particles several micrometers in size, including hexagonal ZnO nanocrystals with an average size about16 nm and ZnCr2O4 spinel crystals. In the luminescence spectrum of the Cu/ZnO-ZnCr2O4 composite in the visible region, fluorescence bands are observed characteristic of ZnCr2O4 crystals and structural defects of ZnO crystals. It was found that the intensity of singlet oxygen photogeneration by the Cu/ZnO-ZnCr2O4 nanocomposite linearly depends on the power density of the exciting radiation (the wavelength is 405 nm). Antibacterial activity of the Cu/ZnO-ZnCr2O4 nanocomposite against Staphylococcus aureus ATCC 209P bacteria was also revealed. The obtained nanocomposite powders can be used in water and air purification and disinfection systems.


  • Open Access

    Organic-inorganic light-absorbing composites for near infrared part of spectrum

    by Sergei K. Evstropiev, Valery M. Volynkin, D.V. Bulyga, V.A. Ostrovskii, K.N. Makarov, K.V. Dukelskii, G.S. Polishchuk

    Synthesis and study on structure and properties of organic-inorganic composites based on epoxy resin, CuO and Fe3O4 absorbing light in infrared part of spectrum was performed. The composites synthesis was performed by introduction of CuO and Fe3O4 micropowders into liquid epoxy composition with subsequent homogenization of the mixture and polymerization. The study on structure and properties of organic-inorganic composites was performed by methods of optical microscopy, infrared and visible spectroscopy, study on microhardness. According to the IR spectroscopy data, introduction of oxide particles leads to decrease in epoxy polymer degree of calcification. The composites containing Fe3O4 show relatively low light reflection until 4.2 % in the spectral range of 1000–1100 nm that corresponds to the theoretical estimation data. Incorporation of CuO and Fe3O4 micropowders into the epoxy polymer leads to an increase in microhardness from 120 to 160 MPa. Obtained experimental data can serve as the base for development of IR-absorbing organic-inorganic composites for laser technology.


  • Open Access

    Polymer-salt synthesis and study on structure of vanadium-doped yttrium-aluminum garnet

    by Sergei K. Evstropiev, V.A. Ostrovskii, K.N. Makarov, D.V. Bulyga, Valery M. Volynkin, A.V. Sandulenko, K.V. Dukelskii, G.S. Polishchuk

    Nanoscaled YAG:V powders were synthesized using low-temperature polymer-salt method. A comparison of their structure with monocrystals structure was performed. Structure, morphology and chemical composition of materials were studied using XRD, SEM and energy-dispersive X-ray spectroscopy. Estimation of average sizes of nanocrystals and crystal cell parameters was performed based on XRD data. The results were compared with the results obtained earlier for YAG:V monocrystals. Nanopowders synthesized at 1000 °C consist from microscopic aggregates of YAG:V nanocrystals with average size of 43 nm and crystal structure characteristic for YAG monocrystals. It was found that V3+ incorporation and their substitution of aluminum ions leads to distortion of crystal cell. It was shown that this phenomenon is observed both in YAG:V monocrystals and nanopowders synthesized using low-temperature polymer-salt method. The infrared spectroscopy data shows the similarity of the monocrystal and nanopowders structure. Obtained powders can be applied for fabrication of light-absorbing optical ceramics and organo-inorganic composites.

  • Thin photocatalytic and bactericidal coatings based on carbon or metal oxide nanoparticles

    by S.K. Evstropiev, A.V. Karavaeva, K.V. Dukelskii, K.S. Evstropyev, E.V. Kolobkova, I.M. Belousova, V.M. Kiselev, N.V. Nikonorov

    The application of liquid polymer-salt method allows to form transparent oxide coatings on the glass surface. Prepared coatings are thin (200-250 nm) and uniform and fully cover the glass surface. Experimental data show that these coatings consist of small (10-20 nm) nanocrystals. Transparent nanocoatings demonstrate high bactericidal properties and the ability to generate singlet oxygen under UV irradiation.

  • NONLINEAR OPTICAL TRANSFORMATION OF PICOSECOND LASER PULSES IN MULTIMODE MICROSTRUCTURED FIBERS WITH LIMITED NONLINEARITY

    by Research and production association S.I. Vavilov State Optical Institute, V. Demidov, K. Dukelskii, The Bonch-Bruevich State University of Telecommunications, S. Leonov, Bauman Moscow State Technical University, A. Matrosova


  • Photocatalytic transparent coatings on the surface of the tips of medical fibre-optic bundles

    by S Konstantinovich Evstrop'Ev, V M Volynkin, V M Kiselev, K V Dukel'Skii, Kirill Sergeevich Evstrop'Ev, Viktor Vladimirovich Demidov, Yu A Gatchin


  • 2-Fold inner cladding symmetry design for actualizing 100μm-core class double-clad large-pitch fibers with the preferential fundamental mode amplification property

    by Vladimir V. Demidov, Konstantin V. Dukelskii, Sergey K. Evstropiev, Yuri A. Gatchin, Egishe V. Ter-Nersesyants, Pavel V. Bezborodkin

    Silica/air large-pitch photonic crystal fibers, known simply as large-pitch fibers (LPFs) due to their hole-to-hole spacing 10 times larger than the wavelength, performing mode-field diameters (MFDs) about 50 μm along with nearly diffraction-limited output beam quality provide a versatile platform for realizing compact and stable multi-kW average power and multi-mJ pulse energy ultrashort pulse fiber laser systems [1]. Major efforts have been devoted to improving mode delocalization phenomena in Yb-doped double-cladding LPFs with a view to reduce the spatial overlap of higher-order modes (HOMs) with the doped area [2]. However, the thermo-optic effect which changes the refractive index profile and reconfines a group of the most competitive HOMs (TE01, HE21, TM01) in the gain region jeopardizes the acceptable conditions for the practical fundamental mode (FM) operation and consequently power scaling capabilities of such fibers [3]. For this reason, development of new double-clad LPF designs providing extended HOMs delocalization properties under the extreme heat load is an urgent challenge in the field of fiber laser technologies.