Research of parameters of fusion splices of telecommunication multimode optical fibers and silica microstructured fiber lightguides with hexagonal configuration
Authors:
- A. V. BourdineA. V. Bourdine
- V. G. NesterovVNV. G. Nesterov
- M. A. OrlovMOM. A. Orlov
- A. S. EvtushenkoAEA. S. Evtushenko
- S. S. PashinSPS. S. Pashin
- E. S. ZaitsevaEZE. S. Zaitseva
- A. A. BelyaevABA. A. Belyaev
- D. N. ShurupovDSD. N. Shurupov
- V. V. DemidovVDV. V. Demidov
- E. V. Ter-NersesyantsETE. V. Ter-Nersesyants
- К. В. ДукельскийКДК. В. Дукельский
- G. S. PolishchukGPG. S. Polishchuk
Open Access
- 25 February 2026
- journal article
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 26 (1) , 1-14
Abstract
This work presents the results of experimental approbation of the ability to fuse telecommunication graded index multimode optical fibers of ISO/IEC Category OM2+/OM3 and silica microstructured optical fibers by using a commercially available field fusion splicer kit Fujikura-36S (Fujikura Ltd., Japan). We tested silica microstructured optical fiber with a hexagonal configuration that provides quasi-singlemode operation over an extended spectral band up to short wavelengths (λ = 800–1700 nm) in comparison with conventional singlemode optical fiber of ratified ITU-T Recommendations. The potential possibilities were explored for reducing of attenuation by selection and combination of fusion program parameters (arc current and arc time) to find a compromise between quality fusion splicing without any defects and minimization of insertion loss. About 1.5 m long short segment of researched microstructured optical fiber was spliced between two spools with multimode fibers, while each one of them was also spliced with two pigtailed spools with singlemode optical fibers. Fiber length of each spool was at the least 1 km long in order to provide insertion loss measurements by using optical time domain reflectometer EXFO AXS-110 (EXFO, Canad a). Based on a series of experiment, we have identified an optimal combination of arc current (STD-30 a.u.) and arc time (1100 ms) which provides desired compromise between reducing the fusion program parameters to prevent the MOF air hole collapsing under the quality splice without defects, and decreased insertion loss. As a result, the total insertion loss has been reduced to 0.8–1.0 dB and more in comparison with the reference value. For instance, mentioned above program settings gave the loss 5.721 dB under the reference value 6.722 dB. Therefore, the experimental results confirm ability of fusion splicing microstructured and multimode optical fibers with an acceptable insertion loss by using commercially available field fusion splicer kits. This provides to utilize proposed microstructured optical fibers with extended singlemode operation wavelength range in various applications of laser technology, optical devices and short-range high bit rate optical networks.Keywords
This publication has 29 references indexed in Scilit:
- Practical experience in joining of silica microstructured and telecommunication optical fibers by using field arc fusion splicer kits2025
- Low-Loss, Low-Back-Reflection Fusion Splicing of Large-Mode-Area Fibers With Nested Hollow-Core Antiresonant Fibers for All-Fiber High-Power, Single-Frequency Fiber Laser TransmissionJournal of Lightwave Technology, 2025
- (INVITED) Advances in photonic crystal fiber: sensing and supercontinuum generation applicationsOptical Fiber Technology, 2022
- Functionalized Micro Structured Optical Fibers and Devices for Sensing Applications: A ReviewJournal of Lightwave Technology, 2020
- Optimum splicing of high-index core microstructured optical fibers and traditional single-mode fibers using improved field modelOptics & Laser Technology, 2019
- High strength fusion splicing of hollow core photonic crystal fiber and single-mode fiber by large offset reheatingOptical Fiber Technology, 2016
- Extremely small-core photonic crystal fiber fusion splicing with a single-mode fiber2013
- Characterization and fusion splicing of single-mode photonic crystal fibers2013
- Fusion splicing small-core photonic crystal fibers and single-mode fibers by controlled air hole collapseOptics Communications, 2012
- Fusion Splicing Photonic Crystal Fibers and Conventional Single-Mode Fibers: Microhole Collapse EffectJournal of Lightwave Technology, 2007