Nimal Naser
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Nimal Naser has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Subram Mani Sarathy
Clean Energy Research Platform, Physical Sciences and Engineering (PSE) Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Saudi Arabia
19 shared publications - Suk Ho Chung
King Abdullah Univ Sci & Technol, Clean Combust Res Ctr, Thuwal, Saudi Arabia
11 shared publications - Robert L. McCormick
National Renewable Energy Laboratory
9 shared publications - Gina M. Fioroni
National Laboratory of the Rockies, Golden, CO (United States)
6 shared publications - Samah Y. Mohamed
National Renewable Energy Laboratory, Golden, Colorado 80401, United States
5 shared publications - Abdul Gani Abdul Jameel
Department of Chemical Engineering, King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia
4 shared publications
Latest Publications
- Open Access
- 7 May 2026
- Published by Office of Scientific and Technical Information (OSTI)
An Overview of Potential Future Aviation Energy Carriers
Global jet fuel demand is projected to grow to 165 billion gallons by 2050 and there is growing interest in the aviation industry to understand the capabilities of alternative energy carriers. This report considers several potential energy carriers, reviewing their production potential, operational considerations, and economic implications to inform potential next steps in aeronautics research. The following energy carriers (i.e., fuels) were evaluated in this study for future use in aviation: sustainable aviation fuel (SAF) - both biomass-based and power-to-liquids (PtL) - based SAF - cryogenic hydrogen (LH2) - also known as liquid hydrogen - liquefied natural gas (LNG), liquefied ethane (LE), and Jet X. The barriers and opportunities for the evaluated energy carriers vary. SAF is a commercially available drop-in fuel compatible with existing aircraft and infrastructure. SAF is limited by both higher prices and slow commercialization of multiple pathways using different feedstocks necessary to significantly grow supply. Cryogenic fuels, in contrast, have very different thermal, physical, and chemical properties than SAF and Jet A, requiring the construction of new airport storage and dispensing infrastructure and the design of new aircraft energy systems capable of mitigating heat transfer and boil-off. Cryogenic fuels offer an opportunity to diversify aviation fuel carriers from domestic energy relevant for both energy security and resilience. This means cryogenic fuels are more of a longer-term solution for aircraft but are worth exploring for potential future cost savings and emissions benefits. Jet X refers to non-drop-in liquid hydrocarbon fuels in the early stages of investigation seeking favorable properties. There are substantial barriers to non-drop-in liquid aviation fuels that are not compatible with existing aircraft and fuel infrastructure.
- 7 May 2026
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAn Overview of Potential Future Aviation Energy Carriers
Global jet fuel demand is projected to grow to 165 billion gallons by 2050 and there is growing interest in the aviation industry to understand the capabilities of alternative energy carriers. This report considers several potential energy carriers, reviewing their production potential, operational considerations, and economic implications to inform potential next steps in aeronautics research. The following energy carriers (i.e., fuels) were evaluated in this study for future use in aviation: sustainable aviation fuel (SAF) - both biomass-based and power-to-liquids (PtL) - based SAF - cryogenic hydrogen (LH2) - also known as liquid hydrogen - liquefied natural gas (LNG), liquefied ethane (LE), and Jet X. The barriers and opportunities for the evaluated energy carriers vary. SAF is a commercially available drop-in fuel compatible with existing aircraft and infrastructure. SAF is limited by both higher prices and slow commercialization of multiple pathways using different feedstocks necessary to significantly grow supply. Cryogenic fuels, in contrast, have very different thermal, physical, and chemical properties than SAF and Jet A, requiring the construction of new airport storage and dispensing infrastructure and the design of new aircraft energy systems capable of mitigating heat transfer and boil-off. Cryogenic fuels offer an opportunity to diversify aviation fuel carriers from domestic energy relevant for both energy security and resilience. This means cryogenic fuels are more of a longer-term solution for aircraft but are worth exploring for potential future cost savings and emissions benefits. Jet X refers to non-drop-in liquid hydrocarbon fuels in the early stages of investigation seeking favorable properties. There are substantial barriers to non-drop-in liquid aviation fuels that are not compatible with existing aircraft and fuel infrastructure.
- Open Access
- 15 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Flow Reactor Study and Kinetic Model Development of HEFA-SPK and its Surrogate
In this work, we formulate a two-component surrogate for HEFA-SPK, incorporating aromatic or cycloalkane components, and develop reduced kinetic models for the surrogates to be used in high-performance computing simulations. The HEFA-SPK surrogate was selected and optimized based on the fuel's physical and combustion properties, including ignition delay times and flame speeds. The resulting surrogate consists of 40% n-undecane and 60% 2-methylnonane. The surrogate was confirmed by flow reactor experiments for both the HEFA-SPK fuel and the suggested two-component surrogates, where excellent agreement was observed. To meet aromatic requirements, 1,2,4-trimethylbenzene (8%) was selected, and we determined that incorporating 30% propylcyclohexane into the HEFA-SPK will achieve a volume swell equivalent to 8% aromatics. The properties of the surrogates were measured, and a new reduced kinetic model was developed based on the semi-decoupling methodology, using a reduced CH4 chemistry from NUIG 1.0 as base chemistry. Kinetic models will be employed in combustor simulations to enable a comprehensive understanding of the effect of SAF fuel properties on aviation combustor performance.
- 15 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessFlow Reactor Study and Kinetic Model Development of HEFA-SPK and its Surrogate
In this work, we formulate a two-component surrogate for HEFA-SPK, incorporating aromatic or cycloalkane components, and develop reduced kinetic models for the surrogates to be used in high-performance computing simulations. The HEFA-SPK surrogate was selected and optimized based on the fuel's physical and combustion properties, including ignition delay times and flame speeds. The resulting surrogate consists of 40% n-undecane and 60% 2-methylnonane. The surrogate was confirmed by flow reactor experiments for both the HEFA-SPK fuel and the suggested two-component surrogates, where excellent agreement was observed. To meet aromatic requirements, 1,2,4-trimethylbenzene (8%) was selected, and we determined that incorporating 30% propylcyclohexane into the HEFA-SPK will achieve a volume swell equivalent to 8% aromatics. The properties of the surrogates were measured, and a new reduced kinetic model was developed based on the semi-decoupling methodology, using a reduced CH4 chemistry from NUIG 1.0 as base chemistry. Kinetic models will be employed in combustor simulations to enable a comprehensive understanding of the effect of SAF fuel properties on aviation combustor performance.
- 1 January 2026
- Published by National Laboratory of the Rockies
Evaluation of Ethanol Use in Marine Shipping
- 1 January 2026
- Published by National Laboratory of the Rockies
Evaluation of Ethanol Use in Marine Shipping
- Open Access
- 24 November 2025
- Published by Office of Scientific and Technical Information (OSTI)
Storage Stability of 50% Biodiesel Blends and Neat Biodiesel Produced in North America
This study investigated aging of two petroleum diesel, seven B100, three B20 blends, and 14 B50 blends representing the full range of fuels in the North American market for 12-weeks at 43 degrees Celsius under the ASTM D4625 accelerated aging protocol. Twelve-weeks under D4625 aging represents approximately 12 months of storage time in clean, dry conditions. Samples were taken every two weeks for measurement of Rancimat induction period (IP), peroxide content, and TAN; and total insoluble were measured at the end of the 12-week test. The petroleum diesel samples showed no evidence of oxidation over the 12-week test. B100 samples slowly oxidized over the 12-week test to have reduced IP, below 2 h for the least stable samples. The three mid-range stability samples (initial IP 5-6 h) showed increased levels of peroxide but did not enter exponential growth (remained in Phase 1). One sample with an initial induction period of roughly 3 h, showed levels of insoluble over the method reproducibility at the end of the test. These results show B100 samples with initial IP greater than 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage. B20 made from biodiesel 31980 exhibited some peroxide formation over 12 weeks, as was also the case for this biodiesel when aged as B100. Neither of the other B20 samples evaluated showed peroxide formation and none of the samples showed increased TAN. None of these samples had measurable insoluble at the end of the test (<2 mg/100 mL). Consistent with our previous work, B20 blends with IP greater than 6 h are stable in D4625 storage for more than 12 weeks, indicating that real fuels can be stored in a clean dry environment for at least 12 months. For B50 blends, while initial IP values are slightly higher for blends into one of the petroleum diesel fuels, the results for the two petroleum blendstocks are very similar. IP values decreased slowly over time, but in all cases remained above 2 h. Corresponding roughly to the B100 results, there was some growth in peroxides the B50 samples made with lower IP B100, but no significant change in acid number over time. One B50 sample showed insoluble formation at a value of 5.4 +/- 1 mg/100 mL, slightly above the repeatability of the test method. The B100 used for this B50 sample also produced a similar amount of insoluble when aged as B100. These results show B50 blends with initial IP greater than 6 h and made with an initial B100 IP of over 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage.
- 24 November 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessStorage Stability of 50% Biodiesel Blends and Neat Biodiesel Produced in North America
This study investigated aging of two petroleum diesel, seven B100, three B20 blends, and 14 B50 blends representing the full range of fuels in the North American market for 12-weeks at 43 degrees Celsius under the ASTM D4625 accelerated aging protocol. Twelve-weeks under D4625 aging represents approximately 12 months of storage time in clean, dry conditions. Samples were taken every two weeks for measurement of Rancimat induction period (IP), peroxide content, and TAN; and total insoluble were measured at the end of the 12-week test. The petroleum diesel samples showed no evidence of oxidation over the 12-week test. B100 samples slowly oxidized over the 12-week test to have reduced IP, below 2 h for the least stable samples. The three mid-range stability samples (initial IP 5-6 h) showed increased levels of peroxide but did not enter exponential growth (remained in Phase 1). One sample with an initial induction period of roughly 3 h, showed levels of insoluble over the method reproducibility at the end of the test. These results show B100 samples with initial IP greater than 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage. B20 made from biodiesel 31980 exhibited some peroxide formation over 12 weeks, as was also the case for this biodiesel when aged as B100. Neither of the other B20 samples evaluated showed peroxide formation and none of the samples showed increased TAN. None of these samples had measurable insoluble at the end of the test (<2 mg/100 mL). Consistent with our previous work, B20 blends with IP greater than 6 h are stable in D4625 storage for more than 12 weeks, indicating that real fuels can be stored in a clean dry environment for at least 12 months. For B50 blends, while initial IP values are slightly higher for blends into one of the petroleum diesel fuels, the results for the two petroleum blendstocks are very similar. IP values decreased slowly over time, but in all cases remained above 2 h. Corresponding roughly to the B100 results, there was some growth in peroxides the B50 samples made with lower IP B100, but no significant change in acid number over time. One B50 sample showed insoluble formation at a value of 5.4 +/- 1 mg/100 mL, slightly above the repeatability of the test method. The B100 used for this B50 sample also produced a similar amount of insoluble when aged as B100. These results show B50 blends with initial IP greater than 6 h and made with an initial B100 IP of over 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage.
- Open Access
- 30 October 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (45) , 22048-22060
Flow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane
Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM International’s SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI) produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.
- 30 October 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (45) , 22048-22060
Open AccessFlow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane
Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM International’s SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI) produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.
- Open Access
- 26 May 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (22) , 10479-10487
Measurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels
Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.
- 26 May 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (22) , 10479-10487
Open AccessMeasurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels
Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.
- Open Access
- 22 December 2024
- Published by Elsevier in Fuel Communications
- Vol. 22
Properties and Autoignition reactivity of diesel boiling range ethers produced from Guerbet alcohols
- 22 December 2024
- Published by Elsevier in Fuel Communications
- Vol. 22
Open AccessProperties and Autoignition reactivity of diesel boiling range ethers produced from Guerbet alcohols
- Open Access
- 31 October 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (22) , 22501-22515
Chemical Kinetics Investigations of Dibutyl Ether Isomers Oxidation in a Laminar Flow Reactor
The combustion kinetics of three symmetric diesel-boiling-range ether isomers were investigated experimentally using a plug flow reactor. The isomers were di-n-butyl ether (DNBE), diisobutyl ether (DIBE), and di-sec-butyl ether (DSBE). The flow reactor experiments employed oxygen as the oxidizer and helium as the diluent, with oxidation carried out at atmospheric and elevated pressure conditions and temperatures from 400 to 1000 at 20 K intervals. The fuel, oxidizer, and diluent flow rates were varied at different temperatures to maintain a constant initial fuel mole fraction of 1000 ppm under stoichiometric conditions and a residence time of 2 s. Reaction products were analyzed by gas chromatography (GC). Depending on the structure, ethers showed different degrees of negative temperature coefficient (NTC) behavior. Speciation results from the GC analysis were then compared to simulations using existing and newly developed chemical kinetic models. Most of the simulated product concentrations showed reasonable agreement with the experimental data. The chemical kinetic models were utilized to elucidate key features of the reactivity and NTC behavior of the different isomers. The chemical kinetic analysis indicates that the combustion behaviors of the three isomers are influenced by the key species formed at the low-temperature reaction regime. The key species identified for DNBE, DIBE, and DSBE at atmospheric pressure are n-butanal, isobutanal, and sec-butanol, respectively.
- 31 October 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (22) , 22501-22515
Open AccessChemical Kinetics Investigations of Dibutyl Ether Isomers Oxidation in a Laminar Flow Reactor
The combustion kinetics of three symmetric diesel-boiling-range ether isomers were investigated experimentally using a plug flow reactor. The isomers were di-n-butyl ether (DNBE), diisobutyl ether (DIBE), and di-sec-butyl ether (DSBE). The flow reactor experiments employed oxygen as the oxidizer and helium as the diluent, with oxidation carried out at atmospheric and elevated pressure conditions and temperatures from 400 to 1000 at 20 K intervals. The fuel, oxidizer, and diluent flow rates were varied at different temperatures to maintain a constant initial fuel mole fraction of 1000 ppm under stoichiometric conditions and a residence time of 2 s. Reaction products were analyzed by gas chromatography (GC). Depending on the structure, ethers showed different degrees of negative temperature coefficient (NTC) behavior. Speciation results from the GC analysis were then compared to simulations using existing and newly developed chemical kinetic models. Most of the simulated product concentrations showed reasonable agreement with the experimental data. The chemical kinetic models were utilized to elucidate key features of the reactivity and NTC behavior of the different isomers. The chemical kinetic analysis indicates that the combustion behaviors of the three isomers are influenced by the key species formed at the low-temperature reaction regime. The key species identified for DNBE, DIBE, and DSBE at atmospheric pressure are n-butanal, isobutanal, and sec-butanol, respectively.
- 21 June 2024
- Published by Elsevier in Combustion and Flame
- Vol. 267
An experimental and chemical kinetic modeling study of 4-butoxyheptane combustion
- 21 June 2024
- Published by Elsevier in Combustion and Flame
- Vol. 267
An experimental and chemical kinetic modeling study of 4-butoxyheptane combustion