Gina M. Fioroni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gina M. Fioroni has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Robert L. McCormick
National Renewable Energy Laboratory
14 shared publications - Nimal Naser
National Renewable Energy Laboratory
6 shared publications - Samah Y. Mohamed
National Renewable Energy Laboratory, Golden, Colorado 80401, United States
6 shared publications - Seonah Kim
Department of Chemistry, Colorado State University, Fort Collins, CO 80523, USA
6 shared publications - Charles Stewart Mcenally
Department of Chemical & Environmental Engineering, Yale University, New Haven, CT 06520, USA
5 shared publications Jon Luecke
4 shared publications
Latest Publications
- Open Access
- 16 February 2026
- Published byĀ Office of Scientific and Technical Information (OSTI)
Opportunities and Challenges for Hydrotreating of Catalytic Fast Pyrolysis Oil to Fuels
Catalytic fast pyrolysis (CFP) provides a versatile platform for producing fuels to combat climate change and meet decarbonizing targets. In this contribution, we will discuss the hydroprocessing of CFP oils to a variety of fuels, including sustainable aviation fuel (SAF), diesel, and marine fuel. Both standalone and co-hydroprocessing with petroleum streams will be covered. Hydrotreating CFP oil at temperatures around 400 Degrees Celsius can produce a highly deoxygenated product with oxygen contents below the detection limit. However, the quality of fuel fractions produced has been a problem, manifesting as low octane numbers for the gasoline-range fraction and low cetane numbers for the diesel-range fraction. Incorporating an initial transition zone for hydrogenation during hydrotreating was shown to dramatically increase the diesel fraction cetane number from 24 to 45. A similar approach enabled the production of a cycloalkane-rich SAF fraction meeting key ASTM 4054 guidelines with respect to density, viscosity, heating value, volatility, freeze and flash point. Over 400 hours of hydrotreating for SAF was demonstrated with no signs of catalyst bed fouling, measured by pressure drop over the catalyst bed. Compared to other fuels, marine fuel is unique in that it does not require complete deoxygenation. We investigated the minimum hydrotreating requirements to produce fuel compatible with very low sulfur fuel oil, and the results suggested 30% reduction in hydrotreating costs for this approach. Co-hydroprocessing offers an opportunity to take advantage of refinery infrastructure and economies of scale although the operation is less flexible with respect to operating conditions. Co-hydroprocessing CFP oil with petroleum streams gave efficient deoxygenation at milder conditions (e.g. at temperatures of 320 Degrees Celsius) than required for standalone hydrotreating. Over 90% incorporation of biogenic carbon in the CFP oil was confirmed by carbon-14 analysis. Hydrotreating of CFP oil, whether by standalone or co-processing, can produce a variety of fuel cuts, whose quality can be tailored by changing process conditions. Challenges remain, including long-term catalyst performance and determining CFP oil quality requirements.
- 16 February 2026
- Published byĀ Office of Scientific and Technical Information (OSTI)
Open AccessOpportunities and Challenges for Hydrotreating of Catalytic Fast Pyrolysis Oil to Fuels
Catalytic fast pyrolysis (CFP) provides a versatile platform for producing fuels to combat climate change and meet decarbonizing targets. In this contribution, we will discuss the hydroprocessing of CFP oils to a variety of fuels, including sustainable aviation fuel (SAF), diesel, and marine fuel. Both standalone and co-hydroprocessing with petroleum streams will be covered. Hydrotreating CFP oil at temperatures around 400 Degrees Celsius can produce a highly deoxygenated product with oxygen contents below the detection limit. However, the quality of fuel fractions produced has been a problem, manifesting as low octane numbers for the gasoline-range fraction and low cetane numbers for the diesel-range fraction. Incorporating an initial transition zone for hydrogenation during hydrotreating was shown to dramatically increase the diesel fraction cetane number from 24 to 45. A similar approach enabled the production of a cycloalkane-rich SAF fraction meeting key ASTM 4054 guidelines with respect to density, viscosity, heating value, volatility, freeze and flash point. Over 400 hours of hydrotreating for SAF was demonstrated with no signs of catalyst bed fouling, measured by pressure drop over the catalyst bed. Compared to other fuels, marine fuel is unique in that it does not require complete deoxygenation. We investigated the minimum hydrotreating requirements to produce fuel compatible with very low sulfur fuel oil, and the results suggested 30% reduction in hydrotreating costs for this approach. Co-hydroprocessing offers an opportunity to take advantage of refinery infrastructure and economies of scale although the operation is less flexible with respect to operating conditions. Co-hydroprocessing CFP oil with petroleum streams gave efficient deoxygenation at milder conditions (e.g. at temperatures of 320 Degrees Celsius) than required for standalone hydrotreating. Over 90% incorporation of biogenic carbon in the CFP oil was confirmed by carbon-14 analysis. Hydrotreating of CFP oil, whether by standalone or co-processing, can produce a variety of fuel cuts, whose quality can be tailored by changing process conditions. Challenges remain, including long-term catalyst performance and determining CFP oil quality requirements.
- Open Access
- 15 January 2026
- Published byĀ Office of Scientific and Technical Information (OSTI)
Flow Reactor Study and Kinetic Model Development of HEFA-SPK and its Surrogate
In this work, we formulate a two-component surrogate for HEFA-SPK, incorporating aromatic or cycloalkane components, and develop reduced kinetic models for the surrogates to be used in high-performance computing simulations. The HEFA-SPK surrogate was selected and optimized based on the fuel's physical and combustion properties, including ignition delay times and flame speeds. The resulting surrogate consists of 40% n-undecane and 60% 2-methylnonane. The surrogate was confirmed by flow reactor experiments for both the HEFA-SPK fuel and the suggested two-component surrogates, where excellent agreement was observed. To meet aromatic requirements, 1,2,4-trimethylbenzene (8%) was selected, and we determined that incorporating 30% propylcyclohexane into the HEFA-SPK will achieve a volume swell equivalent to 8% aromatics. The properties of the surrogates were measured, and a new reduced kinetic model was developed based on the semi-decoupling methodology, using a reduced CH4 chemistry from NUIG 1.0 as base chemistry. Kinetic models will be employed in combustor simulations to enable a comprehensive understanding of the effect of SAF fuel properties on aviation combustor performance.
- 15 January 2026
- Published byĀ Office of Scientific and Technical Information (OSTI)
Open AccessFlow Reactor Study and Kinetic Model Development of HEFA-SPK and its Surrogate
In this work, we formulate a two-component surrogate for HEFA-SPK, incorporating aromatic or cycloalkane components, and develop reduced kinetic models for the surrogates to be used in high-performance computing simulations. The HEFA-SPK surrogate was selected and optimized based on the fuel's physical and combustion properties, including ignition delay times and flame speeds. The resulting surrogate consists of 40% n-undecane and 60% 2-methylnonane. The surrogate was confirmed by flow reactor experiments for both the HEFA-SPK fuel and the suggested two-component surrogates, where excellent agreement was observed. To meet aromatic requirements, 1,2,4-trimethylbenzene (8%) was selected, and we determined that incorporating 30% propylcyclohexane into the HEFA-SPK will achieve a volume swell equivalent to 8% aromatics. The properties of the surrogates were measured, and a new reduced kinetic model was developed based on the semi-decoupling methodology, using a reduced CH4 chemistry from NUIG 1.0 as base chemistry. Kinetic models will be employed in combustor simulations to enable a comprehensive understanding of the effect of SAF fuel properties on aviation combustor performance.
- Open Access
- 24 November 2025
- Published byĀ Office of Scientific and Technical Information (OSTI)
Storage Stability of 50% Biodiesel Blends and Neat Biodiesel Produced in North America
This study investigated aging of two petroleum diesel, seven B100, three B20 blends, and 14 B50 blends representing the full range of fuels in the North American market for 12-weeks at 43 degrees Celsius under the ASTM D4625 accelerated aging protocol. Twelve-weeks under D4625 aging represents approximately 12 months of storage time in clean, dry conditions. Samples were taken every two weeks for measurement of Rancimat induction period (IP), peroxide content, and TAN; and total insoluble were measured at the end of the 12-week test. The petroleum diesel samples showed no evidence of oxidation over the 12-week test. B100 samples slowly oxidized over the 12-week test to have reduced IP, below 2 h for the least stable samples. The three mid-range stability samples (initial IP 5-6 h) showed increased levels of peroxide but did not enter exponential growth (remained in Phase 1). One sample with an initial induction period of roughly 3 h, showed levels of insoluble over the method reproducibility at the end of the test. These results show B100 samples with initial IP greater than 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage. B20 made from biodiesel 31980 exhibited some peroxide formation over 12 weeks, as was also the case for this biodiesel when aged as B100. Neither of the other B20 samples evaluated showed peroxide formation and none of the samples showed increased TAN. None of these samples had measurable insoluble at the end of the test (<2 mg/100 mL). Consistent with our previous work, B20 blends with IP greater than 6 h are stable in D4625 storage for more than 12 weeks, indicating that real fuels can be stored in a clean dry environment for at least 12 months. For B50 blends, while initial IP values are slightly higher for blends into one of the petroleum diesel fuels, the results for the two petroleum blendstocks are very similar. IP values decreased slowly over time, but in all cases remained above 2 h. Corresponding roughly to the B100 results, there was some growth in peroxides the B50 samples made with lower IP B100, but no significant change in acid number over time. One B50 sample showed insoluble formation at a value of 5.4 +/- 1 mg/100 mL, slightly above the repeatability of the test method. The B100 used for this B50 sample also produced a similar amount of insoluble when aged as B100. These results show B50 blends with initial IP greater than 6 h and made with an initial B100 IP of over 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage.
- 24 November 2025
- Published byĀ Office of Scientific and Technical Information (OSTI)
Open AccessStorage Stability of 50% Biodiesel Blends and Neat Biodiesel Produced in North America
This study investigated aging of two petroleum diesel, seven B100, three B20 blends, and 14 B50 blends representing the full range of fuels in the North American market for 12-weeks at 43 degrees Celsius under the ASTM D4625 accelerated aging protocol. Twelve-weeks under D4625 aging represents approximately 12 months of storage time in clean, dry conditions. Samples were taken every two weeks for measurement of Rancimat induction period (IP), peroxide content, and TAN; and total insoluble were measured at the end of the 12-week test. The petroleum diesel samples showed no evidence of oxidation over the 12-week test. B100 samples slowly oxidized over the 12-week test to have reduced IP, below 2 h for the least stable samples. The three mid-range stability samples (initial IP 5-6 h) showed increased levels of peroxide but did not enter exponential growth (remained in Phase 1). One sample with an initial induction period of roughly 3 h, showed levels of insoluble over the method reproducibility at the end of the test. These results show B100 samples with initial IP greater than 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage. B20 made from biodiesel 31980 exhibited some peroxide formation over 12 weeks, as was also the case for this biodiesel when aged as B100. Neither of the other B20 samples evaluated showed peroxide formation and none of the samples showed increased TAN. None of these samples had measurable insoluble at the end of the test (<2 mg/100 mL). Consistent with our previous work, B20 blends with IP greater than 6 h are stable in D4625 storage for more than 12 weeks, indicating that real fuels can be stored in a clean dry environment for at least 12 months. For B50 blends, while initial IP values are slightly higher for blends into one of the petroleum diesel fuels, the results for the two petroleum blendstocks are very similar. IP values decreased slowly over time, but in all cases remained above 2 h. Corresponding roughly to the B100 results, there was some growth in peroxides the B50 samples made with lower IP B100, but no significant change in acid number over time. One B50 sample showed insoluble formation at a value of 5.4 +/- 1 mg/100 mL, slightly above the repeatability of the test method. The B100 used for this B50 sample also produced a similar amount of insoluble when aged as B100. These results show B50 blends with initial IP greater than 6 h and made with an initial B100 IP of over 6 h do not exhibit significant acid number or insoluble formation under D4625 conditions which represent 12 months in clean, dry storage.
- Open Access
- 30 October 2025
- Published byĀ American Chemical Society (ACS)Ā inĀ Energy & Fuels
- Vol.Ā 39 Ā (45) , 22048-22060
Flow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane
Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM Internationalās SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI)īø produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.
- 30 October 2025
- Published byĀ American Chemical Society (ACS)Ā inĀ Energy & Fuels
- Vol.Ā 39 Ā (45) , 22048-22060
Open AccessFlow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane
Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM Internationalās SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI)īø produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.
- Open Access
- 22 December 2024
- Published byĀ ElsevierĀ inĀ Fuel Communications
- Vol.Ā 22
Properties and Autoignition reactivity of diesel boiling range ethers produced from Guerbet alcohols
- 22 December 2024
- Published byĀ ElsevierĀ inĀ Fuel Communications
- Vol.Ā 22
Open AccessProperties and Autoignition reactivity of diesel boiling range ethers produced from Guerbet alcohols
- Open Access
- 31 October 2024
- Published byĀ American Chemical Society (ACS)Ā inĀ Energy & Fuels
- Vol.Ā 38 Ā (22) , 22501-22515
Chemical Kinetics Investigations of Dibutyl Ether Isomers Oxidation in a Laminar Flow Reactor
The combustion kinetics of three symmetric diesel-boiling-range ether isomers were investigated experimentally using a plug flow reactor. The isomers were di-n-butyl ether (DNBE), diisobutyl ether (DIBE), and di-sec-butyl ether (DSBE). The flow reactor experiments employed oxygen as the oxidizer and helium as the diluent, with oxidation carried out at atmospheric and elevated pressure conditions and temperatures from 400 to 1000 at 20 K intervals. The fuel, oxidizer, and diluent flow rates were varied at different temperatures to maintain a constant initial fuel mole fraction of 1000 ppm under stoichiometric conditions and a residence time of 2 s. Reaction products were analyzed by gas chromatography (GC). Depending on the structure, ethers showed different degrees of negative temperature coefficient (NTC) behavior. Speciation results from the GC analysis were then compared to simulations using existing and newly developed chemical kinetic models. Most of the simulated product concentrations showed reasonable agreement with the experimental data. The chemical kinetic models were utilized to elucidate key features of the reactivity and NTC behavior of the different isomers. The chemical kinetic analysis indicates that the combustion behaviors of the three isomers are influenced by the key species formed at the low-temperature reaction regime. The key species identified for DNBE, DIBE, and DSBE at atmospheric pressure are n-butanal, isobutanal, and sec-butanol, respectively.
- 31 October 2024
- Published byĀ American Chemical Society (ACS)Ā inĀ Energy & Fuels
- Vol.Ā 38 Ā (22) , 22501-22515
Open AccessChemical Kinetics Investigations of Dibutyl Ether Isomers Oxidation in a Laminar Flow Reactor
The combustion kinetics of three symmetric diesel-boiling-range ether isomers were investigated experimentally using a plug flow reactor. The isomers were di-n-butyl ether (DNBE), diisobutyl ether (DIBE), and di-sec-butyl ether (DSBE). The flow reactor experiments employed oxygen as the oxidizer and helium as the diluent, with oxidation carried out at atmospheric and elevated pressure conditions and temperatures from 400 to 1000 at 20 K intervals. The fuel, oxidizer, and diluent flow rates were varied at different temperatures to maintain a constant initial fuel mole fraction of 1000 ppm under stoichiometric conditions and a residence time of 2 s. Reaction products were analyzed by gas chromatography (GC). Depending on the structure, ethers showed different degrees of negative temperature coefficient (NTC) behavior. Speciation results from the GC analysis were then compared to simulations using existing and newly developed chemical kinetic models. Most of the simulated product concentrations showed reasonable agreement with the experimental data. The chemical kinetic models were utilized to elucidate key features of the reactivity and NTC behavior of the different isomers. The chemical kinetic analysis indicates that the combustion behaviors of the three isomers are influenced by the key species formed at the low-temperature reaction regime. The key species identified for DNBE, DIBE, and DSBE at atmospheric pressure are n-butanal, isobutanal, and sec-butanol, respectively.
- Open Access
- 17 September 2024
- Published byĀ American Chemical Society (ACS)Ā inĀ The Journal of Physical Chemistry A
- Vol.Ā 128 Ā (38) , 8220-8231
High-Pressure Rate Rules for Ether Alkylperoxy Radical Isomerization
The first isomerization reaction of an alkylperoxy (RO2) radical holds significant importance in low-temperature oxidation, as it governs the branching ratios of the hydroperoxyalkyl (QOOH) radicals, which influence the competition between the chain-propagation and chain-branching reactions. In this study, we systematically calculated high-pressure rate rules for the RO2 isomerization reaction of monoethers, exploring 5-, 6-, 7-, and 8-membered ring transition states. Primary, secondary, and tertiary carbon sites, where both the abstracting peroxy group and the abstracted hydrogen are located, were considered, with particular emphasis on distinguishing between secondary carbons adjacent (alpha) and nonadjacent to the ether functional group. Using the G4//B3LYP/6-311++G(2df,2pd) level of theory and the transition state theory, we estimated the rate constants and the Arrhenius coefficient for over 120 possible isomerization reactions. We examined the effect of ring size and ring atoms, revealing that 6- and 7-membered ring isomerizations were generally the fastest. The impact of the ether functional group on transition states was investigated by comparing reactions with identical ring size, peroxy, and radical positions, but with the ether functional group positioned either outside (i.e., out) or inside (i.e., in) the transition state ring, leading to differences in the rate constants. When comparing to analogous alkane rate constants, differences of up to an order of magnitude were observed, underscoring the need for caution when assigning rate rules by analogy. We applied our rate constants in the di-iso-butyl ether kinetic model and evaluated their influence on low-temperature chemistry finding that they altered the branching ratios by up to a factor of 9, highlighting the significance of site-specific rate constants for more accurate low-temperature modeling.
- 17 September 2024
- Published byĀ American Chemical Society (ACS)Ā inĀ The Journal of Physical Chemistry A
- Vol.Ā 128 Ā (38) , 8220-8231
Open AccessHigh-Pressure Rate Rules for Ether Alkylperoxy Radical Isomerization
The first isomerization reaction of an alkylperoxy (RO2) radical holds significant importance in low-temperature oxidation, as it governs the branching ratios of the hydroperoxyalkyl (QOOH) radicals, which influence the competition between the chain-propagation and chain-branching reactions. In this study, we systematically calculated high-pressure rate rules for the RO2 isomerization reaction of monoethers, exploring 5-, 6-, 7-, and 8-membered ring transition states. Primary, secondary, and tertiary carbon sites, where both the abstracting peroxy group and the abstracted hydrogen are located, were considered, with particular emphasis on distinguishing between secondary carbons adjacent (alpha) and nonadjacent to the ether functional group. Using the G4//B3LYP/6-311++G(2df,2pd) level of theory and the transition state theory, we estimated the rate constants and the Arrhenius coefficient for over 120 possible isomerization reactions. We examined the effect of ring size and ring atoms, revealing that 6- and 7-membered ring isomerizations were generally the fastest. The impact of the ether functional group on transition states was investigated by comparing reactions with identical ring size, peroxy, and radical positions, but with the ether functional group positioned either outside (i.e., out) or inside (i.e., in) the transition state ring, leading to differences in the rate constants. When comparing to analogous alkane rate constants, differences of up to an order of magnitude were observed, underscoring the need for caution when assigning rate rules by analogy. We applied our rate constants in the di-iso-butyl ether kinetic model and evaluated their influence on low-temperature chemistry finding that they altered the branching ratios by up to a factor of 9, highlighting the significance of site-specific rate constants for more accurate low-temperature modeling.