Ping Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ping Zhou has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Elmar Beeh
DLR Institut für Fahrzeugkonzepte
3 shared publications - Horst E. Friedrich
Institute of Vehicle Concepts, German Aerospace Center (DLR), Stuttgart, Germany
3 shared publications Bo Liu
2 shared publicationsElmar Beeh
German Aerospace Centre (DLR), Institute of Vehicle Concepts, Stuttgart, Germany
2 shared publicationsGundolf Kopp
German Aerospace Centre (DLR), Institute of Vehicle Concepts, Stuttgart, Germany
2 shared publicationsHorst E. Friedrich
German Aerospace Centre (DLR), Institute of Vehicle Concepts, Stuttgart, Germany
2 shared publications
Latest Publications
- Open Access
- 16 April 2026
- Published by Elsevier in SSRN Electronic Journal
Failure analysis of pore-controlled ductile fracture in die-cast AM60 magnesium alloy under tensile and bulge loading
High-pressure die casting (HPDC) magnesium alloys often contain internal defects, such as pores and shrinkage cavities, which significantly degrade ductility and fracture resistance. In this study, AM60 die-cast magnesium alloy was investigated to elucidate the mechanisms of defect-controlled ductile fracture. Room-temperature uniaxial tensile tests, in situ SEM tensile tests, and bulge tests were performed to characterize pore evolution and its influence on fracture behavior. In situ SEM observations revealed a typical damage sequence of pore nucleation, growth, and coalescence, with pores preferentially forming at the interfaces between inclusions and the α-Mg matrix or near initial defects. Ligament necking promoted pore coalescence and subsequent crack propagation, indicating a local plasticity-controlled fracture mechanism. A Gurson–Tvergaard–Needleman (GTN) damage model was employed to establish a quantitative link between pore evolution and macroscopic fracture behavior. The model parameters were calibrated and validated against uniaxial tensile and bulge experiments. The results demonstrated good agreement in terms of crack initiation, crack morphology, limiting dome height, and regional pore evolution. In addition, zone-based SEM observations and pore area fraction statistics revealed a clear radial gradient of damage evolution in the bulged specimens, providing microscopic support for the GTN-predicted void evolution stages. This study provides mechanistic insight into defect-controlled fracture in die-cast magnesium alloys and quantitative support for failure assessment and defect-tolerant design of thin-walled HPDC magnesium components.
- 16 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFailure analysis of pore-controlled ductile fracture in die-cast AM60 magnesium alloy under tensile and bulge loading
High-pressure die casting (HPDC) magnesium alloys often contain internal defects, such as pores and shrinkage cavities, which significantly degrade ductility and fracture resistance. In this study, AM60 die-cast magnesium alloy was investigated to elucidate the mechanisms of defect-controlled ductile fracture. Room-temperature uniaxial tensile tests, in situ SEM tensile tests, and bulge tests were performed to characterize pore evolution and its influence on fracture behavior. In situ SEM observations revealed a typical damage sequence of pore nucleation, growth, and coalescence, with pores preferentially forming at the interfaces between inclusions and the α-Mg matrix or near initial defects. Ligament necking promoted pore coalescence and subsequent crack propagation, indicating a local plasticity-controlled fracture mechanism. A Gurson–Tvergaard–Needleman (GTN) damage model was employed to establish a quantitative link between pore evolution and macroscopic fracture behavior. The model parameters were calibrated and validated against uniaxial tensile and bulge experiments. The results demonstrated good agreement in terms of crack initiation, crack morphology, limiting dome height, and regional pore evolution. In addition, zone-based SEM observations and pore area fraction statistics revealed a clear radial gradient of damage evolution in the bulged specimens, providing microscopic support for the GTN-predicted void evolution stages. This study provides mechanistic insight into defect-controlled fracture in die-cast magnesium alloys and quantitative support for failure assessment and defect-tolerant design of thin-walled HPDC magnesium components.
- 22 November 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 205
Modeling of fatigue damage evolution and life prediction of aluminum adhesive joints subjected to hygrothermal aging
- 22 November 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 205
Modeling of fatigue damage evolution and life prediction of aluminum adhesive joints subjected to hygrothermal aging
- 22 July 2016
- Published by Taylor & Francis in International Journal of Crashworthiness
- Vol. 21 (6) , 597-613
Dynamic bending behaviour of magnesium alloy rectangular thin-wall beams filled with polyurethane foam
This study proposes a hybrid structural design concept of polyurethane foam-filled magnesium alloy AZ31B rectangular thin-walled beams which serve as energy absorbing components in automotive applications. Uniaxial tensile and compressive tests, and fracture tests were performed to investigate the material mechanical properties. Dynamic three-point bending tests were performed to study the deformation/fracture modes and energy absorption capacity for the foam-filled AZ31B beams, and to compare these mechanical properties with those for mild steel DC04 beams. Different AZ31B beams were filled with a variation of foam density (0.05, 0.20 and 0.30 g/cm3). It was found that the AZ31B beam filled with 0.20 g/cm3 foam reached the highest specific energy absorption; moreover, it absorbed more energy and reached much higher specific energy absorption than the foam-filled DC04 beam filled with the same foam, although the former one was nearly 54% lighter. The potential advantage of the foam-filled AZ31B beams is possibly associated with the high work hardening rate of AZ31B sheet in compression, which may involve more material in plastic deformation compared with the foam-filled DC04 beams. It has therefore been demonstrated that the hybrid structural design concept of the polyurethane foam-filled AZ31B beam has potential applications in auto-body structures.
- 22 July 2016
- Published by Taylor & Francis in International Journal of Crashworthiness
- Vol. 21 (6) , 597-613
Dynamic bending behaviour of magnesium alloy rectangular thin-wall beams filled with polyurethane foam
This study proposes a hybrid structural design concept of polyurethane foam-filled magnesium alloy AZ31B rectangular thin-walled beams which serve as energy absorbing components in automotive applications. Uniaxial tensile and compressive tests, and fracture tests were performed to investigate the material mechanical properties. Dynamic three-point bending tests were performed to study the deformation/fracture modes and energy absorption capacity for the foam-filled AZ31B beams, and to compare these mechanical properties with those for mild steel DC04 beams. Different AZ31B beams were filled with a variation of foam density (0.05, 0.20 and 0.30 g/cm3). It was found that the AZ31B beam filled with 0.20 g/cm3 foam reached the highest specific energy absorption; moreover, it absorbed more energy and reached much higher specific energy absorption than the foam-filled DC04 beam filled with the same foam, although the former one was nearly 54% lighter. The potential advantage of the foam-filled AZ31B beams is possibly associated with the high work hardening rate of AZ31B sheet in compression, which may involve more material in plastic deformation compared with the foam-filled DC04 beams. It has therefore been demonstrated that the hybrid structural design concept of the polyurethane foam-filled AZ31B beam has potential applications in auto-body structures.
- 31 May 2016
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 25 (7) , 2866-2877
Mechanical Behavior and Microstructural Analysis of Extruded AZ31B Magnesium Alloy Processed by Backward Extrusion
- 31 May 2016
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 25 (7) , 2866-2877
Mechanical Behavior and Microstructural Analysis of Extruded AZ31B Magnesium Alloy Processed by Backward Extrusion
- 18 February 2016
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 25 (3) , 853-865
Influence of Tension-Compression Asymmetry on the Mechanical Behavior of AZ31B Magnesium Alloy Sheets in Bending
- 18 February 2016
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 25 (3) , 853-865
Influence of Tension-Compression Asymmetry on the Mechanical Behavior of AZ31B Magnesium Alloy Sheets in Bending
- Open Access
- 1 January 2016
- Published by Springer Nature in Strength of Materials
- Vol. 48 (1) , 69-76
Coupled Effects of Strain Rate and Temperature on Deformation Twinning in Cu-Zn Alloy
- 1 January 2016
- Published by Springer Nature in Strength of Materials
- Vol. 48 (1) , 69-76
Open AccessCoupled Effects of Strain Rate and Temperature on Deformation Twinning in Cu-Zn Alloy
- 27 October 2015
- Published by Springer Nature in Experimental Mechanics
- Vol. 56 (3) , 513-519
A Novel Testing Method for Uniaxial Compression of Thin-Sheet Magnesium Alloys
- 27 October 2015
- Published by Springer Nature in Experimental Mechanics
- Vol. 56 (3) , 513-519
A Novel Testing Method for Uniaxial Compression of Thin-Sheet Magnesium Alloys