Abolfazl Abedi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Abolfazl Abedi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Javad Sharifi
Shahid Beheshti University
4 shared publications - Gholam-Mohammad Parsanasab
Integrated Photonics Laboratory, Faculty of Electrical Engineering, Shahid Beheshti University, Tehran, Iran
2 shared publications - Hamed Nikbakht
VU University Amsterdam
2 shared publications - Hamid Latifi
Department of Physics, Laser and Plasma Research Institute, Shahid Beheshti University, Tehran, Iran
2 shared publications - Majid Taghavi
Shahid Beheshti Univ. (Iran, Islamic Republic of)
2 shared publications - Christopher John Pastras
School of Engineering, Macquarie University, Sydney, Australia
1 shared publication
Latest Publications
- Open Access
- 8 December 2021
- Published by The Royal Society in Journal of The Royal Society Interface
- Vol. 18 (185)
Polymeric piezoresistive airflow sensor to monitor respiratory patterns
Monitoring human respiratory patterns is of great importance as it gives essential information for various medical conditions, e.g. sleep apnoea syndrome and chronic obstructive pulmonary disease and asthma, etc. Herein, we have developed a polymeric airflow sensor based on nanocomposites of vertically grown graphene nanosheets (VGNs) with polydimethylsiloxane (PDMS) and explored their applications in monitoring human respiration. The sensing performance of the VGNs/PDMS nanocomposite was characterized by exposing to a range of airflow rates (20–130 l min −1 ), and a linear performance with high sensitivity and low response time (mostly below 1 s) was observed. To evaluate the experimental results, finite-element simulation models were developed in the COMSOL Multiphysics package. The piezoresistive properties of VGNs/PDMS thin film and fluid–solid interaction were thoroughly studied. Laser Doppler vibrometry measures of sensor tip displacement closely approximated simulated deflection results and validated the dynamic response of the sensor. By comparing the proposed sensor and some other airflow sensors in the literature, it is concluded that the VGNs/PDMS airflow sensor has excellent features in terms of sensor height, detection range and sensitivity. The potential application of the VGNs/PDMS airflow sensor in detecting the respiration pattern of human exercises like walking, jogging and running has been demonstrated.
- 8 December 2021
- Published by The Royal Society in Journal of The Royal Society Interface
- Vol. 18 (185)
Open AccessPolymeric piezoresistive airflow sensor to monitor respiratory patterns
Monitoring human respiratory patterns is of great importance as it gives essential information for various medical conditions, e.g. sleep apnoea syndrome and chronic obstructive pulmonary disease and asthma, etc. Herein, we have developed a polymeric airflow sensor based on nanocomposites of vertically grown graphene nanosheets (VGNs) with polydimethylsiloxane (PDMS) and explored their applications in monitoring human respiration. The sensing performance of the VGNs/PDMS nanocomposite was characterized by exposing to a range of airflow rates (20–130 l min −1 ), and a linear performance with high sensitivity and low response time (mostly below 1 s) was observed. To evaluate the experimental results, finite-element simulation models were developed in the COMSOL Multiphysics package. The piezoresistive properties of VGNs/PDMS thin film and fluid–solid interaction were thoroughly studied. Laser Doppler vibrometry measures of sensor tip displacement closely approximated simulated deflection results and validated the dynamic response of the sensor. By comparing the proposed sensor and some other airflow sensors in the literature, it is concluded that the VGNs/PDMS airflow sensor has excellent features in terms of sensor height, detection range and sensitivity. The potential application of the VGNs/PDMS airflow sensor in detecting the respiration pattern of human exercises like walking, jogging and running has been demonstrated.
- 9 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (12) , 13156-13164
A Dual-Axis MOEMS Accelerometer
This paper is a report on the design and fabrication of a dual-axis micro-opto-electro-mechanical system (MOEMS) accelerometer. The device consists of a proof mass (PM) suspended by four L-shaped springs. Two Fabry-Pérot (FP) cavities are formed between the cross-sections of the PM and the ends of two cleaved optical fibers in perpendicular directions (the X and Y axes). The acceleration causes the proof mass to move in the reverse direction relative to the applied acceleration. The sensor is fabricated by a silicon-on-insulator wafer. The fabricated sensor is characterized both by spectral monitoring and power measurements in the range of ±1 g. The results of spectral measurements show 3.23 nm/g (g=9.81 m/s2: gravity constant) and 3.19 nm/g to the applied acceleration along the X and Y axes, respectively. Moreover, the obtained resolutions for the two directions of X and Y are 309 μg and 313 μg, respectively. Besides, the sensitivity of the sensor in power measurements is 550 mV/g and 528 mV/g in the X and Y directions, respectively. The sensor also possesses the resonant frequencies of 1382.5 Hz and 1398.6 Hz in the X and Y axes, respectively, in the range of ±1 g. The maximum cross-axis sensitivities obtained for this sensor are below 0.19% for each pair of X, Y, and Z axes. This value is fewer than the cross-axis sensitivity of most micro electro-mechanical systems without any post processing. This small value is a result of insensitivity of the FP spectrum to the lateral displacements of the PM.
- 9 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (12) , 13156-13164
A Dual-Axis MOEMS Accelerometer
This paper is a report on the design and fabrication of a dual-axis micro-opto-electro-mechanical system (MOEMS) accelerometer. The device consists of a proof mass (PM) suspended by four L-shaped springs. Two Fabry-Pérot (FP) cavities are formed between the cross-sections of the PM and the ends of two cleaved optical fibers in perpendicular directions (the X and Y axes). The acceleration causes the proof mass to move in the reverse direction relative to the applied acceleration. The sensor is fabricated by a silicon-on-insulator wafer. The fabricated sensor is characterized both by spectral monitoring and power measurements in the range of ±1 g. The results of spectral measurements show 3.23 nm/g (g=9.81 m/s2: gravity constant) and 3.19 nm/g to the applied acceleration along the X and Y axes, respectively. Moreover, the obtained resolutions for the two directions of X and Y are 309 μg and 313 μg, respectively. Besides, the sensitivity of the sensor in power measurements is 550 mV/g and 528 mV/g in the X and Y directions, respectively. The sensor also possesses the resonant frequencies of 1382.5 Hz and 1398.6 Hz in the X and Y axes, respectively, in the range of ±1 g. The maximum cross-axis sensitivities obtained for this sensor are below 0.19% for each pair of X, Y, and Z axes. This value is fewer than the cross-axis sensitivity of most micro electro-mechanical systems without any post processing. This small value is a result of insensitivity of the FP spectrum to the lateral displacements of the PM.
- 1 March 2020
- Published by Elsevier in Superlattices and Microstructures
- Vol. 139, 106383
Time-dependent quantum transport in the presence of elastic scattering
- 1 March 2020
- Published by Elsevier in Superlattices and Microstructures
- Vol. 139, 106383
Time-dependent quantum transport in the presence of elastic scattering
- 23 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (9) , 1893-1902
Simulation, Fabrication, and Characterization of a Sensitive SU-8-Based Fabry-Pérot MOEMS Accelerometer
This paper presents the design, fabrication, and characterization of a SU-8 four L-shaped beams optical MEMS (MOEMS) accelerometer based on a Fabry-Perot(FP) interferometer. An applied acceleration causes a displacement of the proof mass and changes the cavity of FP resonator. Fabrication process has been simplified such that only two photolithography steps are required and SU-8 is used for both the structural body and the sacrificial layer. To prevent the sacrificial layer from being exposed to UV light, a thin copper layer is coated by physical vapor deposition technique between the two SU-8 layers. The sensor chip consists of a proof mass which is suspended by four L-shaped springs. The movement of the proof mass in response to acceleration is detected by a FP cavity formed between the proof mass and the cleaved end of a single mode optical fiber. The fabricated sensor has a sensitivity of 12.5 μW/g and resonant frequency of 1872 Hz in the range of ±1g.
- 23 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (9) , 1893-1902
Simulation, Fabrication, and Characterization of a Sensitive SU-8-Based Fabry-Pérot MOEMS Accelerometer
This paper presents the design, fabrication, and characterization of a SU-8 four L-shaped beams optical MEMS (MOEMS) accelerometer based on a Fabry-Perot(FP) interferometer. An applied acceleration causes a displacement of the proof mass and changes the cavity of FP resonator. Fabrication process has been simplified such that only two photolithography steps are required and SU-8 is used for both the structural body and the sacrificial layer. To prevent the sacrificial layer from being exposed to UV light, a thin copper layer is coated by physical vapor deposition technique between the two SU-8 layers. The sensor chip consists of a proof mass which is suspended by four L-shaped springs. The movement of the proof mass in response to acceleration is detected by a FP cavity formed between the proof mass and the cleaved end of a single mode optical fiber. The fabricated sensor has a sensitivity of 12.5 μW/g and resonant frequency of 1872 Hz in the range of ±1g.
- 30 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (7) , 3033-3037
Impact of Phonon Scattering on the Negative-Differential-Resistance Behavior in Graphene Nanoribbon p-n Junctions
In this paper, the effect of electron-phonon scattering on the negative differential resistance of graphene nanoribbon p-n junctions is investigated. The results show that the optical phonon scattering, due to inelasticity, significantly increases the valley current such that the peak-to-valley ratio decreases several orders of magnitude compared to ballistic approximation. It also shifts up the valley voltage. The former effect manifests itself more in structures with a smaller band gap and better ballistic characteristics. We show that it remains remarkable in different lengths of the transition region and severely affects the performance of the device. The results also show that phonon scattering plays a significant role even in ultrascaled nanodevices.
- 30 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (7) , 3033-3037
Impact of Phonon Scattering on the Negative-Differential-Resistance Behavior in Graphene Nanoribbon p-n Junctions
In this paper, the effect of electron-phonon scattering on the negative differential resistance of graphene nanoribbon p-n junctions is investigated. The results show that the optical phonon scattering, due to inelasticity, significantly increases the valley current such that the peak-to-valley ratio decreases several orders of magnitude compared to ballistic approximation. It also shifts up the valley voltage. The former effect manifests itself more in structures with a smaller band gap and better ballistic characteristics. We show that it remains remarkable in different lengths of the transition region and severely affects the performance of the device. The results also show that phonon scattering plays a significant role even in ultrascaled nanodevices.
- 14 December 2017
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 17 (1) , 68-75
Quantum Monte Carlo simulation of dissipative transport using Bohmian trajectories
- 14 December 2017
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 17 (1) , 68-75
Quantum Monte Carlo simulation of dissipative transport using Bohmian trajectories